The Compact Linear Collider (CLIC) - 2018 Summary Report

The Compact Linear Collider (CLIC) is a TeV-scale high-luminosity linear $e^+e^-$ collider under development at CERN. Following the CLIC conceptual design published in 2012, this report provides an overview of the CLIC project, its current status, and future developments. It presents the CLIC physics potential and reports on design, technology, and implementation aspects of the accelerator and the detector. CLIC is foreseen to be built and operated in stages, at centre-of-mass energies of 380 GeV, 1.5 TeV and 3 TeV, respectively. CLIC uses a two-beam acceleration scheme, in which 12 GHz accelerating structures are powered via a high-current drive beam. For the first stage, an alternative with X-band klystron powering is also considered. CLIC accelerator optimisation, technical developments and system tests have resulted in an increased energy efficiency (power around 170 MW) for the 380 GeV stage, together with a reduced cost estimate at the level of 6 billion CHF. The detector concept has been refined using improved software tools. Significant progress has been made on detector technology developments for the tracking and calorimetry systems. A wide range of CLIC physics studies has been conducted, both through full detector simulations and parametric studies, together providing a broad overview of the CLIC physics potential. Each of the three energy stages adds cornerstones of the full CLIC physics programme, such as Higgs width and couplings, top-quark properties, Higgs self-coupling, direct searches, and many precision electroweak measurements. The interpretation of the combined results gives crucial and accurate insight into new physics, largely complementary to LHC and HL-LHC. The construction of the first CLIC energy stage could start by 2026. First beams would be available by 2035, marking the beginning of a broad CLIC physics programme spanning 25-30 years

Performance simulations of a phase stabilization system prototype for CTF3

The CLIC drive beam provides RF power for acceleration of the main beam, and hence thedrive beam's longitudinal phase tolerances are very tight. A feedforward chicane consistingof four electromagnetic kickers is proposed as a correction system for the phase errors,which should allow loosening of the tolerances. A prototype of such a chicane systemdeveloped by CERN, INFN and the University of Oxford, is planned to be installed at CTF3 in2012. The present paper summarizes the parameters of the planned phase correction systemand presents simulations, which are used to make predictions of the performance of such afeedforward system at CTF3. Copyright © 2012 by IEEE

The Drive Beam Phase Stability in CTF3 and its Relation to the Bunch Compression Factor

The proposed Compact Linear Collider (CLIC) is based on a two-beam acceleration scheme. The energy needed to accelerate a low intensity “main” beam is provided by a high intensity, low energy “drive” beam. The precision and stability of the phase relation between two beams is crucial for the performance of the scheme. The tolerable phase jitter is 0.2 deg rms at 12 GHz. For this reason it is fundamental to understand the main possible causes of the drive beam timing jitter. Experimental work aimed at such understanding was done in the CLIC Test Facility (CTF3) where a drive beam with characteristics similar to the CLIC one is produced. Several phase measurements allowed us to conclude that the main source of phase jitter is energy jitter of the beam transformed and amplified into phase jitter when passing through a magnetic chicane. This conclusion is supported by measurements done with different momentum compaction values in the chicane. In this paper the results of these several phase measurements will be presented and compared with expectations

Design of phase feed forward system in CTF3 and performance of fast beam phase monitors

The CLIC two beam acceleration technology requires a drive beam phase stability better than 0.3 deg rms at 12 GHz, corresponding to a timing stability below 50 fs rms. For this reason the CLIC design includes a phase stabilization feed-forward system. It relies on precise beam phase measurements and their subsequent correction in a chicane with the help of fast kickers. A prototype of such a system is being installed in the CLIC Test Facility CTF3. In this paper its design and implementation is described in detail. Additionally, the performance of the precision phase monitor prototypes installed at the end of the CTF3 linac, as measured with the drive beam, is presented. Copyright © 2013 by JACoW

Experimental Verification of the CLIC Two-Beam Acceleration Technology in CTF3

The Compact Linear Collider international collaboration is pursuing an extensive R&D program towards a multi- TeV electron-positron collider. In particular, the development of two-beam acceleration technology is the focus of the CLIC test facility CTF3. In this paper we summarise the most recent results obtained at CTF3: The results of the studies on the drive beam generation are presented, the achieved two beam acceleration performance is reported and the measured breakdown rates and related observations are summarised. The stability of the deceleration process performed over 12 subsequent modules and a comparison of the obtained results with the theoretical expectations are discussed. We also outline the future experimental program

Updated baseline for a staged Compact Linear Collider

The Compact Linear Collider (CLIC) is a multi-TeV high-luminosity linear e+e- collider under development. For an optimal exploitation of its physics potential, CLIC is foreseen to be built and operated in a staged approach with three centre-of-mass energy stages ranging from a few hundred GeV up to 3 TeV. The first stage will focus on precision Standard Model physics, in particular Higgs and top-quark measurements. Subsequent stages will focus on measurements of rare Higgs processes, as well as searches for new physics processes and precision measurements of new states, e.g. states previously discovered at LHC or at CLIC itself. In the 2012 CLIC Conceptual Design Report, a fully optimised 3 TeV collider was presented, while the proposed lower energy stages were not studied to the same level of detail. This report presents an updated baseline staging scenario for CLIC. The scenario is the result of a comprehensive study addressing the performance, cost and power of the CLIC accelerator complex as a function of centre-of-mass energy and it targets optimal physics output based on the current physics landscape. The optimised staging scenario foresees three main centre-of-mass energy stages at 380 GeV, 1.5 TeV and 3 TeV for a full CLIC programme spanning 22 years. For the first stage, an alternative to the CLIC drive beam scheme is presented in which the main linac power is produced using X-band klystrons