Synthesis of Bulk Zr48Cu36Al8Ag8 Metallic Glass by Hot Pressing of Amorphous Powders

The critical cooling rate necessary for glass formation via melt solidification poses inherent constraints on sample size using conventional casting techniques. This drawback can be overcome by pressure-assisted sintering of metallic glass powders at temperatures above the glass transition, where the material shows viscous-flow behavior. Partial crystallization during sintering usually exacerbates the inherent brittleness of metallic glasses and thus needs to be avoided. In order to achieve high density of the bulk specimens while avoiding (or minimizing) crystallization, the optimal combination between low viscosity and long incubation time for crystallization must be identified. Here, by carefully selecting the time–temperature window for powder consolidation, we synthesized highly dense Zr48Cu36Ag8Al8 bulk metallic glass (BMG) with mechanical properties comparable with its cast counterpart. The larger ZrCu-based BMG specimens fabricated in this work could then be post-processed by flash-annealing, offering the possibility to fabricate monolithic metallic glasses and glass–matrix composites with enhanced room-temperature plastic deformation

Microstructure, mechanical properties and machinability of particulate reinforced Al matrix composites: a comparative study between SiC particles and high-entropy alloy particles

In this study, 2024Al matrix composites reinforced by SiC particles (SiC-2024Al) and nanocrystalline high-entropy alloy particles (HEA-2024Al) fabricated by powder metallurgy were systematically compared for the first time. There is a significant difference in microstructure and mechanical properties as well as machinability between two kinds of composites. In term of microstructure, when the volume fraction of reinforcements was 10%, both SiC-2024Al and HEA-2024Al composites showed a homogeneous particle distribution in the matrix. With the increase of reinforcement content, HEA-2024Al composites presented denser microstructure than that of SiC-2024Al composites. The composites with 10, 20 and 30 vol.% HEA reinforcements all showed better plasticity than that of the SiC-2024Al composites with same volume fraction of reinforcements, which was related with better particle distribution and interface bonding. However, the strength showed the opposite tendency in the two kinds of composites. Selecting 10SiC-2024Al and 10HEA-2024Al composites as examples to explore the difference in the yield strength of two kinds of composites, it is ascribed to the dislocation punched zones around interface between the Al matrix and reinforcements, which was analyzed in detail by a combination of calculation, nanoindentation tests and finite element analysis. Additionally, HEA-2024Al composites showed better machinability than those of SiC-2024Al composites. This work provides insight into the application of particulate reinforced Al matrix composites

A Voted Regularized Dual Averaging Method for Large-Scale Discriminative Training in Natural Language Processing

Abstract We propose a new algorithm based on the dual averaging method for large-scale discriminative training in natural language processing (NLP), as an alternative to the perceptron algorithms or stochastic gradient descent (SGD). The new algorithm estimates parameters of linear models by minimizing 1 regularized objectives and are effective in obtaining sparse solutions, which is particularly desirable for large scale NLP tasks. We then give the mistake bound of the algorithm, and show how the bound is affected by the additional 1 regularization term. Evaluations on the tasks of parse reranking and statistical machine translation attest the success of the new algorithm

Powder metallurgy of shape memory bulk metallic glass composites: synthesis, properties and deformation mechanism

The synthesis of in-situ bulk metallic glass composites (BMGCs) with crystals that undergo a martensitic transformation under loading is possibly the most effective method to improve the plasticity of metallic glasses at room temperature. These martensitic or shape memory BMGCs are typically fabricated via solidification of glass-forming melts, which requires the meticulous selection of the chemical composition and the proper choice of the processing parameters (particularly the cooling rate) in order to ensure that the glassy matrix coexists with the desired amount of austenitic phase having suitable morphology and characteristics. Unfortunately, a relatively limited number of alloy systems, where austenite and glassy matrix coexist over a wide range of compositions, is available. Additionally, the necessity for rapid heat extraction and the corresponding high cooling rates essential for glass formation by melt solidification set an inherent limit to the achievable dimensions of BMGs and BMGCs specimens. The aim of this thesis is to study the effectiveness of powder metallurgy as an alternative to solidification for the synthesis of shape memory BMGCs. Ni50.6Ti49.4 and Zr48Cu36Al8Ag8 metallic glass powders were selected as the constituents of the composites because they have been extensively investigated and represent well the characteristic behavior of metallic glass and shape memory phases. BMGCs with different volume fractions of NiTi phase were fabricated using pressure-assisted sintering via hot pressing and their microstructure, mechanical properties and deformation mechanism were investigated. Particular focus was placed upon identifying the individual contributions of the martensitic transformation and shear band formation to plasticity as well as their mutual interaction at different length scales using a multidisciplinary approach involving experiments and simulations. BMG composites were synthesized by hot pressing of powder mixtures consisting of Zr48Cu36Al8Ag8 metallic glass and different amounts of Ni50.6Ti49.4 particles (10, 20, 40 and 60 vol.%) using the optimized consolidation parameters (temperature-time-pressure) determined for the monolithic BMG. All composites are characterized by a relatively uniform particle distribution and good interface bonding without any sign of reaction between the metallic glass and NiTi. The NiTi particles are progressively less isolated with increasing volume fraction of NiTi up to 40 % and, for the BMGC with 60 vol.% NiTi, the glassy particles are no longer connected and the NiTi phase becomes the continuous matrix. This is not a trivial achievement as the change of matrix while maintaining the structure of the constituent phases would not be easily obtained by solidification of melts with such different compositions. The size of the samples (10 mm diameter and 9 - 11 mm height) is larger than the characteristic BMGCs synthesized by casting and can, in principle, be scaled up to larger dimensions, demonstrating the effectiveness of this approach for overcoming the size limitation inherent to glass formation via solidification. In contrast to the monolithic BMG, which does not show any sign of plasticity, the BMGCs exhibit macroscopic plastic deformation that progressively increases with increasing NiTi content along with distinct strain-hardening. The BMG composites have similar fracture strength, which is comparable with the monolithic BMG, and exhibit a distinct double yield behavior, similar to shape memory BMGCs fabricated by casting. The deformed BMGCs exhibit a high density of shear bands, again in agreement with what observed for similar BMGCs fabricated by casting. These findings not only demonstrate that BMGCs with tunable microstructures and thus with optimized deformability can be synthesized by pressure-assisted sintering but, thanks to the phase stability of the components across such a wide range of compositions, also offer an excellent platform to examine fundamental aspects in the field of martensitic BMGCs. The confining stress exerted by the surrounding glassy matrix was quantified at the macroscale via a hybrid Voigt-Reuss mixture, which considers intermediate weighted combinations of stiff and compliant behaviors. In this way, the macroscopic stress required to initiate the martensitic transformation from B2 to B19´ can be described with rather good accuracy. The confining effect was further investigated by in-situ high-energy X-ray diffraction to have access to the strain tensor of the B2 phase as a function of loading. The results indicate that the confining stress along the direction perpendicular to the loading axis is particularly strong because the expansion of the B2 phase is constrained by the elastic matrix. A mechanism responsible for shear band formation in shape memory BMGCs is proposed. The stress field generated by the martensitic transformation in the contiguous glass would activate the adjacent shear transformation zone (STZ, the elementary units of plasticity in BMGs). The stress field induced by the activated STZ in the surrounding material then triggers the activation of the following STZs along the path of a potential shear band, in an autocatalytic process resembling the domino effect. The shear band formed in this way propagates through the glassy phase and, when impinging a B2 particle, the associated stress field would locally trigger the martensitic transformation, starting again the process. Molecular dynamics (MD) simulations of a martensitic BMGC show that the structural perturbation generated by the martensitic transformation is indeed transmitted to the adjacent glassy matrix and, in turn, to the developing shear band, in agreement with the proposed mechanism. The individual contribution of the glassy phase to the residual strain after each loading-unloading cycle was quantified assuming that the NiTi phase behaves in the same manner across the different specimens. The glass contribution was then correlated to the shear band density to obtain the plastic strain resulting from shear banding for a given amount of NiTi phase, a quantity that could be effectively used in the design of plastically-deformable BMGCs with shape memory particles. The martensitic transformation in the composites becomes progressively more irreversible with increasing strain. A large contribution to the martensite stabilization may come from the residual stress induced by the shear bands, in accordance with the finite element method (FEM) simulations, showing that residual stresses in the composites suppress the reverse transformation after unloading. These finding corroborates the hypothesis that the residual elastic stress field generated by the shear bands may be fundamental for stabilizing the martensitic phase by restraining the atoms at the glass-crystal interface from rearranging back to form austenite. This process can be reversed by proper heat treatment. The findings presented in this thesis offer the opportunity to synthesize shape memory BMG composites with enhanced plasticity and strain-hardening capability along with larger dimensions than those typically achieved by solidification. The powder metallurgy approach provides the necessary versatility in materials design and resulting properties of the composites via the control over the fundamental microstructural features, such as volume fraction, size, morphology and distribution of the second phase. Additionally, materials processing in the solid state gives a virtually infinite choice among the possible composite components, a degree of freedom not usually given when processing via solidification.:Abstract iii Kurzfassung vii Motivation and objectives xi 1 Theoretical background and state-of-the-art 1 1.1 Bulk metallic glasses (BMGs) 1 1.1.1 Formation of metallic glasses 2 1.1.2 Mechanical properties of BMGs 5 1.1.3 Shear bands in metallic glasses 8 1.2 Bulk metallic glass matrix composites 19 1.2.1 Fabrication of BMG composites 20 1.2.2 In-situ BMG composites 27 1.2.3 Ex-situ BMG composites 43 2 Experiments and simulations 57 2.1 Sample preparation 57 2.1.1 Starting materials 57 2.1.2 Powder mixing 59 2.1.3 Powder consolidation 60 2.2 Materials characterization 61 2.2.1 Composition analysis 61 2.2.2 Laboratory X-ray diffraction 61 2.2.3 High-energy X-ray diffraction and strain analysis 62 2.2.4 Viscosity measurements 63 2.2.5 Differential scanning calorimetry 64 2.2.6 Density measurements 64 2.2.7 X-ray computed tomography 65 2.2.8 Optical microscopy and scanning electron microscopy 65 2.2.9 Transmission electron microscopy 66 2.2.10 Elastic constants measurements 66 2.2.11 Mechanical tests 67 2.3 Molecular dynamic simulations 67 2.4 Finite element simulations 68 3 Pressure-assisted sintering of single-phase Zr48Cu36Al8Ag8 metallic glass and Ni50.6Ti49.4 powders 73 3.1 Synthesis and properties of single-phase Zr48Cu36Al8Ag8 bulk metallic glass 73 3.2 Synthesis and properties of single-phase Ni50.6Ti49.4 shape memory alloy 80 4 Pressure-assisted sintering of BMG composites with shape memory crystals: Microstructure and mechanical properties 87 4.1 Microstructure of BMG composites 87 4.2 Effect of NiTi volume fraction on mechanical properties 90 4.3 Effect of confinement of the glassy phase on the martensitic transformation 95 5 Deformation mechanism of shape memory BMG composites 101 5.1 Martensitic transformation and shear band formation 101 5.2 Mechanism of shear band formation in shape memory BMG composites 107 6 Reversibility of the martensitic transformation in shape memory BMG composites 113 6.1 Martensite stabilization in NiTi alloy and BMG composites 113 6.2 Simulation of the martensite stabilization effect in BMG composites 119 6.3 Effect of heat treatment on the martensitic reverse transformation 121 7 Summary and outlook 125 References 131 Acknowledgements 155 Publications 157 Erklärung 15

Powder metallurgy of shape memory bulk metallic glass composites: synthesis, properties and deformation mechanism

The synthesis of in-situ bulk metallic glass composites (BMGCs) with crystals that undergo a martensitic transformation under loading is possibly the most effective method to improve the plasticity of metallic glasses at room temperature. These martensitic or shape memory BMGCs are typically fabricated via solidification of glass-forming melts, which requires the meticulous selection of the chemical composition and the proper choice of the processing parameters (particularly the cooling rate) in order to ensure that the glassy matrix coexists with the desired amount of austenitic phase having suitable morphology and characteristics. Unfortunately, a relatively limited number of alloy systems, where austenite and glassy matrix coexist over a wide range of compositions, is available. Additionally, the necessity for rapid heat extraction and the corresponding high cooling rates essential for glass formation by melt solidification set an inherent limit to the achievable dimensions of BMGs and BMGCs specimens. The aim of this thesis is to study the effectiveness of powder metallurgy as an alternative to solidification for the synthesis of shape memory BMGCs. Ni50.6Ti49.4 and Zr48Cu36Al8Ag8 metallic glass powders were selected as the constituents of the composites because they have been extensively investigated and represent well the characteristic behavior of metallic glass and shape memory phases. BMGCs with different volume fractions of NiTi phase were fabricated using pressure-assisted sintering via hot pressing and their microstructure, mechanical properties and deformation mechanism were investigated. Particular focus was placed upon identifying the individual contributions of the martensitic transformation and shear band formation to plasticity as well as their mutual interaction at different length scales using a multidisciplinary approach involving experiments and simulations. BMG composites were synthesized by hot pressing of powder mixtures consisting of Zr48Cu36Al8Ag8 metallic glass and different amounts of Ni50.6Ti49.4 particles (10, 20, 40 and 60 vol.%) using the optimized consolidation parameters (temperature-time-pressure) determined for the monolithic BMG. All composites are characterized by a relatively uniform particle distribution and good interface bonding without any sign of reaction between the metallic glass and NiTi. The NiTi particles are progressively less isolated with increasing volume fraction of NiTi up to 40 % and, for the BMGC with 60 vol.% NiTi, the glassy particles are no longer connected and the NiTi phase becomes the continuous matrix. This is not a trivial achievement as the change of matrix while maintaining the structure of the constituent phases would not be easily obtained by solidification of melts with such different compositions. The size of the samples (10 mm diameter and 9 - 11 mm height) is larger than the characteristic BMGCs synthesized by casting and can, in principle, be scaled up to larger dimensions, demonstrating the effectiveness of this approach for overcoming the size limitation inherent to glass formation via solidification. In contrast to the monolithic BMG, which does not show any sign of plasticity, the BMGCs exhibit macroscopic plastic deformation that progressively increases with increasing NiTi content along with distinct strain-hardening. The BMG composites have similar fracture strength, which is comparable with the monolithic BMG, and exhibit a distinct double yield behavior, similar to shape memory BMGCs fabricated by casting. The deformed BMGCs exhibit a high density of shear bands, again in agreement with what observed for similar BMGCs fabricated by casting. These findings not only demonstrate that BMGCs with tunable microstructures and thus with optimized deformability can be synthesized by pressure-assisted sintering but, thanks to the phase stability of the components across such a wide range of compositions, also offer an excellent platform to examine fundamental aspects in the field of martensitic BMGCs. The confining stress exerted by the surrounding glassy matrix was quantified at the macroscale via a hybrid Voigt-Reuss mixture, which considers intermediate weighted combinations of stiff and compliant behaviors. In this way, the macroscopic stress required to initiate the martensitic transformation from B2 to B19´ can be described with rather good accuracy. The confining effect was further investigated by in-situ high-energy X-ray diffraction to have access to the strain tensor of the B2 phase as a function of loading. The results indicate that the confining stress along the direction perpendicular to the loading axis is particularly strong because the expansion of the B2 phase is constrained by the elastic matrix. A mechanism responsible for shear band formation in shape memory BMGCs is proposed. The stress field generated by the martensitic transformation in the contiguous glass would activate the adjacent shear transformation zone (STZ, the elementary units of plasticity in BMGs). The stress field induced by the activated STZ in the surrounding material then triggers the activation of the following STZs along the path of a potential shear band, in an autocatalytic process resembling the domino effect. The shear band formed in this way propagates through the glassy phase and, when impinging a B2 particle, the associated stress field would locally trigger the martensitic transformation, starting again the process. Molecular dynamics (MD) simulations of a martensitic BMGC show that the structural perturbation generated by the martensitic transformation is indeed transmitted to the adjacent glassy matrix and, in turn, to the developing shear band, in agreement with the proposed mechanism. The individual contribution of the glassy phase to the residual strain after each loading-unloading cycle was quantified assuming that the NiTi phase behaves in the same manner across the different specimens. The glass contribution was then correlated to the shear band density to obtain the plastic strain resulting from shear banding for a given amount of NiTi phase, a quantity that could be effectively used in the design of plastically-deformable BMGCs with shape memory particles. The martensitic transformation in the composites becomes progressively more irreversible with increasing strain. A large contribution to the martensite stabilization may come from the residual stress induced by the shear bands, in accordance with the finite element method (FEM) simulations, showing that residual stresses in the composites suppress the reverse transformation after unloading. These finding corroborates the hypothesis that the residual elastic stress field generated by the shear bands may be fundamental for stabilizing the martensitic phase by restraining the atoms at the glass-crystal interface from rearranging back to form austenite. This process can be reversed by proper heat treatment. The findings presented in this thesis offer the opportunity to synthesize shape memory BMG composites with enhanced plasticity and strain-hardening capability along with larger dimensions than those typically achieved by solidification. The powder metallurgy approach provides the necessary versatility in materials design and resulting properties of the composites via the control over the fundamental microstructural features, such as volume fraction, size, morphology and distribution of the second phase. Additionally, materials processing in the solid state gives a virtually infinite choice among the possible composite components, a degree of freedom not usually given when processing via solidification.:Abstract iii Kurzfassung vii Motivation and objectives xi 1 Theoretical background and state-of-the-art 1 1.1 Bulk metallic glasses (BMGs) 1 1.1.1 Formation of metallic glasses 2 1.1.2 Mechanical properties of BMGs 5 1.1.3 Shear bands in metallic glasses 8 1.2 Bulk metallic glass matrix composites 19 1.2.1 Fabrication of BMG composites 20 1.2.2 In-situ BMG composites 27 1.2.3 Ex-situ BMG composites 43 2 Experiments and simulations 57 2.1 Sample preparation 57 2.1.1 Starting materials 57 2.1.2 Powder mixing 59 2.1.3 Powder consolidation 60 2.2 Materials characterization 61 2.2.1 Composition analysis 61 2.2.2 Laboratory X-ray diffraction 61 2.2.3 High-energy X-ray diffraction and strain analysis 62 2.2.4 Viscosity measurements 63 2.2.5 Differential scanning calorimetry 64 2.2.6 Density measurements 64 2.2.7 X-ray computed tomography 65 2.2.8 Optical microscopy and scanning electron microscopy 65 2.2.9 Transmission electron microscopy 66 2.2.10 Elastic constants measurements 66 2.2.11 Mechanical tests 67 2.3 Molecular dynamic simulations 67 2.4 Finite element simulations 68 3 Pressure-assisted sintering of single-phase Zr48Cu36Al8Ag8 metallic glass and Ni50.6Ti49.4 powders 73 3.1 Synthesis and properties of single-phase Zr48Cu36Al8Ag8 bulk metallic glass 73 3.2 Synthesis and properties of single-phase Ni50.6Ti49.4 shape memory alloy 80 4 Pressure-assisted sintering of BMG composites with shape memory crystals: Microstructure and mechanical properties 87 4.1 Microstructure of BMG composites 87 4.2 Effect of NiTi volume fraction on mechanical properties 90 4.3 Effect of confinement of the glassy phase on the martensitic transformation 95 5 Deformation mechanism of shape memory BMG composites 101 5.1 Martensitic transformation and shear band formation 101 5.2 Mechanism of shear band formation in shape memory BMG composites 107 6 Reversibility of the martensitic transformation in shape memory BMG composites 113 6.1 Martensite stabilization in NiTi alloy and BMG composites 113 6.2 Simulation of the martensite stabilization effect in BMG composites 119 6.3 Effect of heat treatment on the martensitic reverse transformation 121 7 Summary and outlook 125 References 131 Acknowledgements 155 Publications 157 Erklärung 15

Powder metallurgy of shape memory bulk metallic glass composites: synthesis, properties and deformation mechanism

The synthesis of in-situ bulk metallic glass composites (BMGCs) with crystals that undergo a martensitic transformation under loading is possibly the most effective method to improve the plasticity of metallic glasses at room temperature. These martensitic or shape memory BMGCs are typically fabricated via solidification of glass-forming melts, which requires the meticulous selection of the chemical composition and the proper choice of the processing parameters (particularly the cooling rate) in order to ensure that the glassy matrix coexists with the desired amount of austenitic phase having suitable morphology and characteristics. Unfortunately, a relatively limited number of alloy systems, where austenite and glassy matrix coexist over a wide range of compositions, is available. Additionally, the necessity for rapid heat extraction and the corresponding high cooling rates essential for glass formation by melt solidification set an inherent limit to the achievable dimensions of BMGs and BMGCs specimens. The aim of this thesis is to study the effectiveness of powder metallurgy as an alternative to solidification for the synthesis of shape memory BMGCs. Ni50.6Ti49.4 and Zr48Cu36Al8Ag8 metallic glass powders were selected as the constituents of the composites because they have been extensively investigated and represent well the characteristic behavior of metallic glass and shape memory phases. BMGCs with different volume fractions of NiTi phase were fabricated using pressure-assisted sintering via hot pressing and their microstructure, mechanical properties and deformation mechanism were investigated. Particular focus was placed upon identifying the individual contributions of the martensitic transformation and shear band formation to plasticity as well as their mutual interaction at different length scales using a multidisciplinary approach involving experiments and simulations. BMG composites were synthesized by hot pressing of powder mixtures consisting of Zr48Cu36Al8Ag8 metallic glass and different amounts of Ni50.6Ti49.4 particles (10, 20, 40 and 60 vol.%) using the optimized consolidation parameters (temperature-time-pressure) determined for the monolithic BMG. All composites are characterized by a relatively uniform particle distribution and good interface bonding without any sign of reaction between the metallic glass and NiTi. The NiTi particles are progressively less isolated with increasing volume fraction of NiTi up to 40 % and, for the BMGC with 60 vol.% NiTi, the glassy particles are no longer connected and the NiTi phase becomes the continuous matrix. This is not a trivial achievement as the change of matrix while maintaining the structure of the constituent phases would not be easily obtained by solidification of melts with such different compositions. The size of the samples (10 mm diameter and 9 - 11 mm height) is larger than the characteristic BMGCs synthesized by casting and can, in principle, be scaled up to larger dimensions, demonstrating the effectiveness of this approach for overcoming the size limitation inherent to glass formation via solidification. In contrast to the monolithic BMG, which does not show any sign of plasticity, the BMGCs exhibit macroscopic plastic deformation that progressively increases with increasing NiTi content along with distinct strain-hardening. The BMG composites have similar fracture strength, which is comparable with the monolithic BMG, and exhibit a distinct double yield behavior, similar to shape memory BMGCs fabricated by casting. The deformed BMGCs exhibit a high density of shear bands, again in agreement with what observed for similar BMGCs fabricated by casting. These findings not only demonstrate that BMGCs with tunable microstructures and thus with optimized deformability can be synthesized by pressure-assisted sintering but, thanks to the phase stability of the components across such a wide range of compositions, also offer an excellent platform to examine fundamental aspects in the field of martensitic BMGCs. The confining stress exerted by the surrounding glassy matrix was quantified at the macroscale via a hybrid Voigt-Reuss mixture, which considers intermediate weighted combinations of stiff and compliant behaviors. In this way, the macroscopic stress required to initiate the martensitic transformation from B2 to B19´ can be described with rather good accuracy. The confining effect was further investigated by in-situ high-energy X-ray diffraction to have access to the strain tensor of the B2 phase as a function of loading. The results indicate that the confining stress along the direction perpendicular to the loading axis is particularly strong because the expansion of the B2 phase is constrained by the elastic matrix. A mechanism responsible for shear band formation in shape memory BMGCs is proposed. The stress field generated by the martensitic transformation in the contiguous glass would activate the adjacent shear transformation zone (STZ, the elementary units of plasticity in BMGs). The stress field induced by the activated STZ in the surrounding material then triggers the activation of the following STZs along the path of a potential shear band, in an autocatalytic process resembling the domino effect. The shear band formed in this way propagates through the glassy phase and, when impinging a B2 particle, the associated stress field would locally trigger the martensitic transformation, starting again the process. Molecular dynamics (MD) simulations of a martensitic BMGC show that the structural perturbation generated by the martensitic transformation is indeed transmitted to the adjacent glassy matrix and, in turn, to the developing shear band, in agreement with the proposed mechanism. The individual contribution of the glassy phase to the residual strain after each loading-unloading cycle was quantified assuming that the NiTi phase behaves in the same manner across the different specimens. The glass contribution was then correlated to the shear band density to obtain the plastic strain resulting from shear banding for a given amount of NiTi phase, a quantity that could be effectively used in the design of plastically-deformable BMGCs with shape memory particles. The martensitic transformation in the composites becomes progressively more irreversible with increasing strain. A large contribution to the martensite stabilization may come from the residual stress induced by the shear bands, in accordance with the finite element method (FEM) simulations, showing that residual stresses in the composites suppress the reverse transformation after unloading. These finding corroborates the hypothesis that the residual elastic stress field generated by the shear bands may be fundamental for stabilizing the martensitic phase by restraining the atoms at the glass-crystal interface from rearranging back to form austenite. This process can be reversed by proper heat treatment. The findings presented in this thesis offer the opportunity to synthesize shape memory BMG composites with enhanced plasticity and strain-hardening capability along with larger dimensions than those typically achieved by solidification. The powder metallurgy approach provides the necessary versatility in materials design and resulting properties of the composites via the control over the fundamental microstructural features, such as volume fraction, size, morphology and distribution of the second phase. Additionally, materials processing in the solid state gives a virtually infinite choice among the possible composite components, a degree of freedom not usually given when processing via solidification.:Abstract iii Kurzfassung vii Motivation and objectives xi 1 Theoretical background and state-of-the-art 1 1.1 Bulk metallic glasses (BMGs) 1 1.1.1 Formation of metallic glasses 2 1.1.2 Mechanical properties of BMGs 5 1.1.3 Shear bands in metallic glasses 8 1.2 Bulk metallic glass matrix composites 19 1.2.1 Fabrication of BMG composites 20 1.2.2 In-situ BMG composites 27 1.2.3 Ex-situ BMG composites 43 2 Experiments and simulations 57 2.1 Sample preparation 57 2.1.1 Starting materials 57 2.1.2 Powder mixing 59 2.1.3 Powder consolidation 60 2.2 Materials characterization 61 2.2.1 Composition analysis 61 2.2.2 Laboratory X-ray diffraction 61 2.2.3 High-energy X-ray diffraction and strain analysis 62 2.2.4 Viscosity measurements 63 2.2.5 Differential scanning calorimetry 64 2.2.6 Density measurements 64 2.2.7 X-ray computed tomography 65 2.2.8 Optical microscopy and scanning electron microscopy 65 2.2.9 Transmission electron microscopy 66 2.2.10 Elastic constants measurements 66 2.2.11 Mechanical tests 67 2.3 Molecular dynamic simulations 67 2.4 Finite element simulations 68 3 Pressure-assisted sintering of single-phase Zr48Cu36Al8Ag8 metallic glass and Ni50.6Ti49.4 powders 73 3.1 Synthesis and properties of single-phase Zr48Cu36Al8Ag8 bulk metallic glass 73 3.2 Synthesis and properties of single-phase Ni50.6Ti49.4 shape memory alloy 80 4 Pressure-assisted sintering of BMG composites with shape memory crystals: Microstructure and mechanical properties 87 4.1 Microstructure of BMG composites 87 4.2 Effect of NiTi volume fraction on mechanical properties 90 4.3 Effect of confinement of the glassy phase on the martensitic transformation 95 5 Deformation mechanism of shape memory BMG composites 101 5.1 Martensitic transformation and shear band formation 101 5.2 Mechanism of shear band formation in shape memory BMG composites 107 6 Reversibility of the martensitic transformation in shape memory BMG composites 113 6.1 Martensite stabilization in NiTi alloy and BMG composites 113 6.2 Simulation of the martensite stabilization effect in BMG composites 119 6.3 Effect of heat treatment on the martensitic reverse transformation 121 7 Summary and outlook 125 References 131 Acknowledgements 155 Publications 157 Erklärung 15

Effect of heat treatment on microstructure and mechanical properties of Al 2024 matrix composites reinforced with Ni60Nb40 metallic glass particles

Al 2024 matrix composites reinforced with 20 and 40 vol% Ni60Nb40 metallic glass particles were synthesized through powder metallurgy using hot pressing and the effect of heat treatment (solution and artificial aging, T6) on microstructure and mechanical properties was examined. The microstructure of the unreinforced matrix shows the formation of CuAl2 and Al2CuMg precipitates after heat treatment, while the composites show the formation of additional CuNiAl and NbNiAl phases due to the reaction between the matrix and glassy particles. The yield strength is improved by the Ni60Nb40 addition in both as-sintered and heat-treated conditions, whereas the ductility is reduced for the composites with 40 vol% of reinforcement. The microstructural modifications due to the interfacial reactions in heat-treated composites result in a significant strengthening contribution. (C) 2019 Elsevier B.V. All rights reserved

Effect of particle size ratio on microstructure and mechanical properties of aluminum matrix composites reinforced with Zr48Cu36Ag8Al8 metallic glass particles

Aluminum matrix composites reinforced with Zr48Cu36Ag8Al8 glassy particles were synthesized by powder metallurgy using reinforcement particles larger than the matrix. The effect of the matrix to reinforcement particle size ratio (PSR) on the microstructure and mechanical properties was studied. The results show that high densification (relative density > 98%) was achieved and the glassy particles retained the amorphous structure in all the composites. Quantitative particle distribution analysis in the three-dimensional space indicated that the homogeneity distribution index decreases with reducing PSR. The findings suggest that a ratio of 1/3 <= PSR <= 1 can be used to obtain composites with rather homogenous distribution of the reinforcement particles. Both compressive and tensile yield strengths of the composites are not sensitive to the PSR change (in the range of 1/3-1/6), whereas the ultimate tensile strength and the ductility are significantly reduced with decreasing PSR; this behavior is accompanied by the change of the fracture mode. The experimental yield strength was found to be consistent with the quantitative strengthening mechanism calculations, and indicated that the reduced matrix ligament size, the thermal mismatch and load bearing are the main strengthening contributions

Effect of Cryomilling on Microstructure and Mechanical Properties of 7050 Aluminum Alloy

The 7050 aluminum alloy samples were prepared from as-atomized 7050 aluminum alloy powder through cryomilling, hot isostatic pressing, hot extrusion and T6 heat treatment. The influence of cryomilling on morphology, grain size and microscopic strain of aluminum alloy powder were analyzed by SEM and XRD. The influence of cryomilling on microstructure and mechanical property of the sample after heat treatment was analyzed by OM, EBSD, TEM, XRD, microhardness and tensile test. The results show that cryomilling can effectively refine the grain size of the material and increase the number of nano-precipitates in the matrix. Compared to the as-atomized powder, the mechanical properties of the 7050 aluminum alloy sample prepared by cryomillied powder are obviously improved

Siderophore Biosynthesis Governs the Virulence of Uropathogenic Escherichia coli by Coordinately Modulating the Differential Metabolism

Urinary tract infections impose substantial health burdens on women worldwide. Urinary tract infections often incur a high risk of recurrence and antibiotic resistance, and uropathogenic E. coli accounts for approximately 80% of clinically acquired cases. The diagnosis of, treatment of, and drug development for urinary tract infections remain substantial challenges due to the complex pathogenesis of this condition. The clinically isolated UPEC 83972 strain was found to produce four siderophores: yersiniabactin, aerobactin, salmochelin, and enterobactin. The biosyntheses of some of these siderophores implies that the virulence of UPEC is mediated via the targeting of primary metabolism. However, the differential modulatory roles of siderophore biosyntheses on the differential metabolomes of UPEC and non-UPEC strains remain incompletely understood. In the present study, we sought to investigate how the differential metabolomes can be used to distinguish UPEC from non-UPEC strains and to determine the associated regulatory roles of siderophore biosynthesis. Our results are the first to demonstrate that the identified differential metabolomes strongly differentiated UPEC from non-UPEC strains. Furthermore, we performed metabolome assays of mutants with different patterns of siderophore deletions; the data revealed that the mutations of all four siderophores exerted a stronger modulatory role on the differential metabolomes of the UPEC and non-UPEC strains relative to the mutation of any single siderophore and that this modulatory role primarily involved amino acid metabolism, oxidative phosphorylation in the carbon fixation pathway, and purine and pyrimidine metabolism. Surprisingly, the modulatory roles were strongly dependent on the type and number of mutated siderophores. Taken together, these results demonstrated that siderophore biosynthesis coordinately modulated the differential metabolomes and thus may indicate novel targets for virulence-based diagnosis, therapeutics, and drug development related to urinary tract infections