6,749 research outputs found
Morphological evolution of a 3D CME cloud reconstructed from three viewpoints
The propagation properties of coronal mass ejections (CMEs) are crucial to
predict its geomagnetic effect. A newly developed three dimensional (3D) mask
fitting reconstruction method using coronagraph images from three viewpoints
has been described and applied to the CME ejected on August 7, 2010. The CME's
3D localisation, real shape and morphological evolution are presented. Due to
its interaction with the ambient solar wind, the morphology of this CME changed
significantly in the early phase of evolution. Two hours after its initiation,
it was expanding almost self-similarly. CME's 3D localisation is quite helpful
to link remote sensing observations to in situ measurements. The investigated
CME was propagating to Venus with its flank just touching STEREO B. Its
corresponding ICME in the interplanetary space shows a possible signature of a
magnetic cloud with a preceding shock in VEX observations, while from STEREO B
only a shock is observed. We have calculated three principle axes for the
reconstructed 3D CME cloud. The orientation of the major axis is in general
consistent with the orientation of a filament (polarity inversion line)
observed by SDO/AIA and SDO/HMI. The flux rope axis derived by the MVA analysis
from VEX indicates a radial-directed axis orientation. It might be that locally
only the leg of the flux rope passed through VEX. The height and speed profiles
from the Sun to Venus are obtained. We find that the CME speed possibly had
been adjusted to the speed of the ambient solar wind flow after leaving COR2
field of view and before arriving Venus. A southward deflection of the CME from
the source region is found from the trajectory of the CME geometric center. We
attribute it to the influence of the coronal hole where the fast solar wind
emanated from.Comment: ApJ, accepte
Scaling of the time-mean characteristics in the polygonal cylinder near-wake
The near wake of the polygonal cylinder with the side number N = 3 ~ ∞ is systematically studied based on particle image velocimetry (PIV) and load-cell measurements. Each cylinder is examined for two orientations, with either one leading side or leading corner. The Reynolds number Re = (1.0 ∼ 6.0) × 104 , defined by the longitudinally projected cylinder width. The dependence of the wake characteristic parameters on the cylinder orientation and N is discussed, and wake scaling analysis is conducted based on these parameters. It is found that the velocity deficit and half width of the wake scale well with the reverse flow zone length and recirculation bubble width, whilst the Strouhal number, drag and fluctuating lift coefficients scale well with the vortex formation length and wake width. The unveiled scaling relationships cast insight into the intrinsic physical connections between the aerodynamic forces and vortex formation and between the polygonal cylinder wakes of N = 3 ~ ∞, suggesting that the understanding of the time-mean wake behind individual polygonal cylinder can be unified to that of the circular cylinder wake
Multiport Bidirectional SRM Drives for Solar-Assisted Hybrid Electric Bus Powertrain With Flexible Driving and Self-Charging Functions
The hybrid electric bus (HEB) presents an emerging solution to exhaust gas emissions in urban transport. This paper proposes a multiport bidirectional switched reluctance motor (SRM) drive for solar-assisted HEB (SHEB) powertrain, which not only improves the motoring performance, but also achieves flexible charging functions. To extend the driving miles and achieve self-charging ability, photovoltaic (PV) panels are installed on the bus to decrease the reliance on fuelsbatteries and charging stations. A bidirectional front-end circuit with a PV-fed circuit is designed to integrate electrical components into one converter. Six driving and five charging modes are achieved. The dc voltage is boosted by the battery in generator control unit (GCU) driving mode and by the charge capacitor in battery driving mode, where the torque capability is improved. Usually, an extra converter is needed to achieve battery charging. In this paper, the battery can be directly charged by the demagnetization current in GCU or PV driving mode, and can be quickly charged by the PV panels and GCUAC grids at SHEB standstill conditions, by utilizing the traction motor windings and integrated converter circuit, without external charging converters. Experiments on a three-phase 128 SRM confirm the effectiveness of the proposed drive and control scheme
Possible Way to Synthesize Superheavy Element Z=117
Within the framework of the dinuclear system model, the production of
superheavy element Z=117 in possible projectile-target combinations is analyzed
systematically. The calculated results show that the production cross sections
are strongly dependent on the reaction systems. Optimal combinations,
corresponding excitation energies and evaporation channels are proposed in this
letter, such as the isotopes ^{248,249}Bk in ^{48}Ca induced reactions in 3n
evaporation channels and the reactions ^{45}Sc+^{246,248}Cm in 3n and 4n
channels, and the system ^{51}V+^{244}Pu in 3n channel.Comment: 10 pages, 4 figures, 1 tabl
Mobile communication base station antenna measurement using unmanned aerial vehicle
Traditional base station antenna measurement methods conducted with professional worker climbing towers tend to raise safety and inefficiency concerns in practical application. Designed to address the above problems, this paper proposes an intelligent and fully automatic antenna measurement unmanned aerial vehicle (UAV) system for mobile communication base station. Firstly, an antenna database, containing 19,715 images, named UAV-Antenna is constructed by image capturing with the help of UAVs flying around various base stations. Secondly, Mask R-CNN is adopted to train an optimal instance segmentation model on UAV-Antenna. Then, pixel coordinates and threshold are utilized for measuring antenna quantity and separate all antenna data for further measuring. Finally, a least squares method is employed for measuring antenna parameters. Experimental results show that the proposed method can not only satisfy the industry application standards, but also guarantee safety of labors and efficiency of performance
- …