A new technique to measure the true contact area using nanoindentation testing

Nanoindentation technique requires the determination of projected contact area under load for calculation of modulus and hardness of materials. This projected contact area is usually calculated by models which take into account the pile-up or sink-in phenomena around the tip. The most commonly used model was developed by Oliver and Pharr [1] which can precisely model the sink-in around the tip, but cannot account for pile-up. Another model developed by Loubet et al can be used [2]. It can take into account the pile-up and the sink-in phenomena and can precisely measure the projected contact area for a large range of materials, except for materials with high strain hardening exponent. Other techniques, like post mortem measurements, can be used. However these measurements do not take into account the elastic recovery during unloading. A new technique to estimate the true projected contact area will be presented. It consists of combining two models (The Dao et al. model and the Kermouche et al. model) that are used normally to calculate the representative stress and the representative strain in indentation. Consequently, the projected contact area calculation does not depend on any contact area model. Moreover, it can account for the pile-up or sink-in phenomenon and the strain hardening of the material, which is not possible with the actual models used. This new technique requires measuring indentations parameters like the maximum load, the contact stiffness and the loading curvature. It requires also the use of two tetrahedral indenters: a Berkovich tip and a tetrahedral tip where the included semi-angle is 50°. The method was tested on three different samples: glass, PMMA and 100C6 steel. For indentations on glass and PMMA samples, the projected contact area was precisely measured. For indentations on 100C6 steel sample, the method was adapted to take into account the Indentation Size Effect observed at small indentation depths. The projected contact area values measured with this new technique will be presented and compared to the values calculated with classical literature models. Also, the limits of the technique will be discusse

Is the second harmonic method applicable for thin films mechanical properties characterization by nanoindentation? Is the second harmonic method applicable for thin films mechanical properties characterization by nanoindentation?

The second harmonic method is a dynamic indentation technique independent of the direct indentation depth measurement. It can be used to determine near-surface mechanical properties of bulk materials more precisely than classical dynamic nano-indentation. In this paper, the second harmonic method is extended to the measurement of the mechanical properties of thin PMMA layers deposited onto silicon wafers. It is shown that this new technique gives precise results at small depths (less than 100nm), even for films with a thickness lower than 500nm, which was not possible to achieve with the classical CSM method. However, experimental and numerical results obtained both with classical nanoindentation and second harmonic methods differ at high indentation depth. Using FE simulations and AFM measurements, it is shown that the contact depth calculation with classical models can explain this difference

Europium retention onto clay minerals from 25 to 150 °C: Experimental measurements, spectroscopic features and sorption modelling

The sorption of Eu(III) onto kaolinite and montmorillonite was investigated up to 150 °C. The clays were purified samples, saturated with Na in the case of montmorillonite. Batch experiments were conducted at 25, 40, 80 and 150 °C in 0.5 M NaClO4 solutions to measure the distribution coefficients (Kd) of Eu as a trace element (<10−6 mol/L) between the solution and kaolinite. For the Na-montmorillonite, we used Kd results from a previous study [Tertre, E., Berger, G., Castet, S., Loubet, M., Giffaut, E., 2005. Experimental study of adsorption of Ni2+, Cs+ and Ln3+ onto Na-montmorillonite up to 150 °C. Geochim. Cosmochim. Acta 69, 4937–4948] obtained under exactly the same conditions. The number and nature of the Eu species sorbed onto both clay minerals were investigated by time resolved laser fluorescence spectroscopy (TRLFS) in specific experiments in the same temperature range. We identified a unique inner-sphere complex linked to the aluminol sites in both clays, assumed to be double bond; length as m-dashAlOEu2+ at the edge of the particles, and a second exchangeable outer-sphere complex for montmorillonite, probably in an interlayer position. The Kd values were used to adjust the parameters of a surface complexation model (DLM: diffuse layer model) from 25 to 150 °C. The number of Eu complexes and the stoichiometry of reactions were constrained by TRLFS. The acidity constants of the amphoteric aluminol sites were taken from another study [Tertre, E., Castet, S., Berger, G., Loubet, M., Giffaut, E. Acid/base surface chemistry of kaolinite and Na-montmorillonite at 25 and 60 °C: experimental study and modelling. Geochim. Cosmochim. Acta, in press], which integrates the influence of the negative structural charge of clays on the acid/base properties of edge sites as a function of temperature and ionic strength. The results of the modelling show that the observed shift of the sorption edge towards low pH with increasing temperature results solely from the contribution of the double bond; length as m-dashAlOEu2+ edge complexes. Finally, we successfully tested the performance of our model by confronting the predictions with experimental Kd data. We used our own data obtained at lower ionic strength (previous study) or higher suspension density and higher starting concentration (TRLFS runs, this study), as well as published data from other experimental studies [Bradbury, M.H., Baeyens, B., 2002. Sorption of Eu on Na and Ca-montmorillonite: experimental investigations and modeling with cation exchange and surface complexation. Geochim. Cosmochim. Acta 66, 2325–2334; Kowal-Fouchard, A., 2002. Etude des mécanismes de rétention des ions U(IV) et Eu(III) sur les argiles: influence des silicates. Ph.D. Thesis, Université Paris Sud, France, 330p]

Nouvelles séquences binaires et quaternaires pour l'étalement de spectre par séquence directe obtenues via les méthodes de Recuit Simulé et de Recherche Taboue

Cet article présente l'application de méthodes combinatoires à l'optimisation de séquences pseudo-aléatoires pour l'étalement de spectre par séquence directe. Cette approche permet pour la première fois la prise en compte des corrélations impaires. Les familles de séquences obtenues, dans les cas binaire et quaternaire, sont comparées à celles de la littérature

Direct sequence spread spectrum sequences

DS-CDMA (for Direct-Sequence Code-Division Multiple-Access, in english, or AMRC, for Accès Multiple à Répartition par les Codes, in french) receivers are significantly performance degraded by the non-orthogonality of the classicaly used spreading sequences, mainly because of the odd correlation functions . The "Tabu Search" algorithm enables sequence generation optimising various criteria . The obtained performance are better than those of the Litterature . Moreover, the proposed method enables the optimisation of sequence sets of any desired length and cardinal, what is not the case for the previous mathematically constructed sequences .Les récepteurs DS-CDMA (pour Direct-Sequence Code-Division Multiple-Access, en anglais, ou AMRC, pour Accès Multiple à Répartition par les Codes, en français) voient leur performance être dégradée de manière significative par la non-orthogonalité des séquences d'étalement classiquement utilisées et principalement à cause des fonctions de corrélation impaires. L'algorithme dit de « Recherche Taboue » (ou Tabu Search, en anglais) permet la génération de séquences optimisant différents critères. Les performances obtenues sont meilleures que celles des séquences de la littérature. De plus, la démarche exposée permet d'optimiser des jeux de séquences de longueur et de cardinal quelconques, ce qui n'est pas le cas des séquences construites de manière mathématique

Influence of Dynamic Ozone Dry Deposition on Ozone Pollution

Identifying the contributions of chemistry and transport to observed ozone pollution using regional-to-global models relies on accurate representation of ozone dry deposition. We use a recently developed configuration of the NOAA GFDL chemistry-climate model - in which the atmosphere and land are coupled through dry deposition-to investigate the influence of ozone dry deposition on ozone pollution over northern midlatitudes. In our model, deposition pathways are tied to dynamic terrestrial processes, such as photosynthesis and water cycling through the canopy and soil. Small increases in winter deposition due to more process-based representation of snow and deposition to surfaces reduce hemispheric-scale ozone throughout the lower troposphere by 5-12 ppb, improving agreement with observations relative to a simulation with the standard configuration for ozone dry deposition. Declining snow cover by the end of the 21st-century tempers the previously identified influence of rising methane on winter ozone. Dynamic dry deposition changes summer surface ozone by -4 to +7 ppb. While previous studies emphasize the importance of uptake by plant stomata, new diagnostic tracking of depositional pathways reveals a widespread impact of nonstomatal deposition on ozone pollution. Daily variability in both stomatal and nonstomatal deposition contribute to daily variability in ozone pollution. Twenty-first century changes in summer deposition result from a balance among changes in individual pathways, reflecting differing responses to both high carbon dioxide (through plant physiology versus biomass accumulation) and water availability. Our findings highlight a need for constraints on the processes driving ozone dry deposition to test representation in regional-to-global models.Peer reviewe

The ALFAM2 database on ammonia emission from field-applied manure: Description and illustrative analysis

peer-reviewedAmmonia (NH3) emission from animal manure contributes to air pollution and ecosystem degradation, and the loss of reactive nitrogen (N) from agricultural systems. Estimates of NH3 emission are necessary for national inventories and nutrient management, and NH3 emission from field-applied manure has been measured in many studies over the past few decades. In this work, we facilitate the use of these data by collecting and organizing them in the ALFAM2 database. In this paper we describe the development of the database and summarise its contents, quantify effects of application methods and other variables on emission using a data subset, and discuss challenges for data analysis and model development. The database contains measurements of emission, manure and soil properties, weather, application technique, and other variables for 1895 plots from 22 research institutes in 12 countries. Data on five manure types (cattle, pig, mink, poultry, mixed, as well as sludge and “other”) applied to three types of crops (grass, small grains, maize, as well as stubble and bare soil) are included. Application methods represented in the database include broadcast, trailing hose, trailing shoe (narrow band application), and open slot injection. Cattle manure application to grassland was the most common combination, and analysis of this subset (with dry matter (DM) limited to <15%) was carried out using mixed- and fixed-effects models in order to quantify effects of management and environment on ammonia emission, and to highlight challenges for use of the database. Measured emission in this subset ranged from <1% to 130% of applied ammonia after 48 h. Results showed clear, albeit variable, reductions in NH3 emission due to trailing hose, trailing shoe, and open slot injection of slurry compared to broadcast application. There was evidence of positive effects of air temperature and wind speed on NH3 emission, and limited evidence of effects of slurry DM. However, random-effects coefficients for differences among research institutes were among the largest model coefficients, and showed a deviation from the mean response by more than 100% in some cases. The source of these institute differences could not be determined with certainty, but there is some evidence that they are related to differences in soils, or differences in application or measurement methods. The ALFAM2 database should be useful for development and evaluation of both emission factors and emission models, but users need to recognize the limitations caused by confounding variables, imbalance in the dataset, and dependence among observations from the same institute. Variation among measurements and in reported variables highlights the importance of international agreement on how NH3 emission should be measured, along with necessary types of supporting data and standard protocols for their measurement. Both are needed in order to produce more accurate and useful ammonia emission measurements. Expansion of the ALFAM2 database will continue, and readers are invited to contact the corresponding author for information on data submission. The latest version of the database is available at http://www.alfam.dk

Reference procedures for the measurement of gaseous emissions from livestock houses and stores of animal manure.

In the ten years before the EMILI 2012 symposium, gaseous losses from animal farms became increasingly important in the m edia. The paradox of this tendency was the great number of publications, scientific or not, even though the emissions of most animal farms had never been measured. Therefor e, the development of reference tools to measure greenhouse gas and ammonia emissio ns was important. Such tools allow recognition and remuneration of the best pract ices and equipment. Accordingly, ADEME funded an international project associating several research and development organizations involved with the animal production chain. The project proposed an initial set of 18 procedures to measure ammonia and greenho use gas emissions from animal houses and manure stores. These were adapted to the diversity of animal farms found throughout the world. Some methods were compared duri ng a ?building? and a ?liquid manure? experiment. Results showed a high difference among methods (ca. 80%), much higher than the estimated uncertainty. Associat ing independent emission measurements, together with a mass balance of the system, is necessary for the reliability of further results. However, previously published references lack uncertainty estimates of measurements that conform to GUM 2008. In the coming years, this is one of the major concerns for measuring emission factor s. Uncertainty estimates should depend on the measurand (temporal: hourly, per batch, yearly; spatial: animal, house, national) and include the uncertainties associated with system representativity and temporal interpolation.Edited by Mélynda Hassouna and Nadine Guingand

Tensions in the periphery: Dependence and the trajectory of a low-cost productive model in the Central and Eastern European automotive industry

This article analyses the productive strategy adopted by Renault for its Dacia plant in Romania. It proposes a detailed analysis of the conditions for the success of the Logan project – Renault’s radical approach to the concept of the low-cost automobile. We look into both market- and production-related aspects that have made the Logan work and highlight the tensions sparked by Renault’s drive to capitalize on its favourable market situation as well as the success achieved by Dacia’s workers in defending their interests. In particular, we emphasize the company governance compromises that have shaped industrial relations at Dacia over the past decades and show how in recent years the maintaining of such a compromise has come increasingly into question due to threats by automation and relocation in a context of constantly rising wages and improving working conditions. Finally, we discuss the strategic dilemmas facing both management and labour and their possible resolutions, as well as the relevance of the Dacia case for understanding the future of Central and Eastern Europe as a peripheral region attracting automotive foreign direct investments