815 research outputs found

    Raman excitation spectroscopy of carbon nanotubes: effects of pressure medium and pressure

    Full text link
    Raman excitation and emission spectra for the radial breathing mode (RBM) are reported, together with a preliminary analysis. From the position of the peaks on the two-dimensional plot of excitation resonance energy against Raman shift, the chiral indices (m, n) for each peak are identified. Peaks shift from their positions in air when different pressure media are added - water, hexane, sulphuric acid - and when the nanotubes are unbundled in water with surfactant and sonication. The shift is about 2 - 3 cm-1 in RBM frequency, but unexpectedly large in resonance energy, being spread over up to 100meV for a given peak. This contrasts with the effect of pressure. The shift of the peaks of semiconducting nanotubes in water under pressure is orthogonal to the shift from air to water. This permits the separation of the effects of the pressure medium and the pressure, and will enable the true pressure coefficients of the RBM and the other Raman peaks for each (m, n) to be established unambiguously.Comment: 6 pages, 3 Figures, Proceedings of EHPRG 2011 (Paris

    The surgical assessment unit: A solution to emergency waiting times?

    Get PDF

    Pressure coefficients of Raman modes of carbon nanotubes resolved by chirality: Environmental effect on graphene sheet

    Get PDF
    Studies of the mechanical properties of single-walled carbon nanotubes are hindered by the availability only of ensembles of tubes with a range of diameters. Tunable Raman excitation spectroscopy picks out identifiable tubes. Under high pressure, the radial breathing mode shows a strong environmental effect shown here to be largely independent of the nature of the environment . For the G-mode, the pressure coefficient varies with diameter consistent with the thick-wall tube model. However, results show an unexpectedly strong environmental effect on the pressure coefficients. Reappraisal of data for graphene and graphite gives the G-mode Grueuneisen parameter gamma = 1.34 and the shear deformation parameter beta = 1.34.Comment: Submitted to Physical Review

    Nanomechanics of graphene oxide-bacteriophage based self-assembled porous composites.

    Get PDF
    Graphene oxide, integrated with the filamentous bacteriophage M13, forms a 3D large-scale multifunctional porous structure by self-assembly, with considerable potential for applications. We performed Raman spectroscopy under pressure on this porous composite to understand its fundamental mechanics. The results show that at low applied pressure, the [Formula: see text] bonds of graphene oxide stiffen very little with increasing pressure, suggesting a complicated behaviour of water intercalated between the graphene layers. The key message of this paper is that water in a confined space can have a significant impact on the nanostructure that hosts it. We introduced carbon nanotubes during the self-assembly of graphene oxide and M13, and a similar porous macro-structure was observed. However, in the presence of carbon nanotubes, pressure is transmitted to the [Formula: see text] bonds of graphene oxide straightforwardly as in graphite. The electrical conductivity of the composite containing carbon nanotubes is improved by about 30 times at a bias voltage of 10 V. This observation suggests that the porous structure has potential in applications where good electrical conductivity is desired, such as sensors and batteries

    From dislocation nucleation to dislocation multiplication in ceramic nanoparticle

    Get PDF
    Magnesium oxide nanocubes are compressed along the [001] direction in situ in the transmission electron microscope. Incipient plasticity in the smaller samples is characterized by the nucleation of few 1/2{110} dislocations while a larger number of line defects is observed in larger nanocubes. Yield and flow stresses scattered stochastically above a minimum value varying as the inverse of the sample size. The upper bound is given by the reduced number of dislocation sources. Such size-dependent behaviour is justified by a detailed statistical analysis and is fully explained by the deformation mechanism

    The removal of thermally aged films of triacylglycerides by surfactant solutions

    Get PDF
    Thermal ageing of triacylglycerides (TAG) at high temperatures produces films which resist removal using aqueous surfactant solutions. We used a mass loss method to investigate the removal of thermally aged TAG films from hard surfaces using aqueous solutions of surfactants of different charge types. It was found that cationic surfactants are most effective at high pH, whereas anionics are most effective at low pH and a non-ionic surfactant is most effective at intermediate pH. We showed that the TAG film removal process occurs in several stages. In the first ‘‘lag phase’’ no TAG removal occurs; the surfactant first partitions into the thermally aged film. In the second stage, the TAG film containing surfactant was removed by solubilisation into micelles in the aqueous solution. The effects of pH and surfactant charge on the TAG removal process correlate with the effects of these variables on the extent of surfactant partitioning to the TAG film and on the maximum extent of TAG solubilisation within the micelles. Additionally, we showed how the TAG removal is enhanced by the addition of amphiphilic additives such as alcohols which act as co-surfactants. The study demonstrates that aqueous surfactant solutions provide a viable and more benign alternative to current methods for the removal of thermally aged TAG films

    Towards a best practice methodology for the detection of Phytophthora species in soils

    Get PDF
    The genus Phytophthora contains species that are major pathogens worldwide, affecting a multitude of plant species across agriculture, horticulture, forestry, and natural ecosystems. Here, we concentrate on those species that are dispersed through soil and water, attacking the roots of the plants, causing them to rot and die. The intention of this study was to compare the soil baiting protocol developed by the Centre for Phytophthora Science and Management (CPSM) with two other baiting methods used in Australia. The aim was to demonstrate the effectiveness of each protocol for soil baiting Phytophthora species in different substrates. Three experiments were conducted: the first to test the sensitivity of each method to detect Phytophthora cinnamomi, the second to test the effect of substrate type (sand or loam), and the third to test the detection of species (P. cinnamomi, P. multivora, or P. pseudocryptogea). The specificity of different plant species baits was compared within and between the methods. Substrate type influenced isolation in all methods; however, the CPSM method was superior regardless of substrate, albeit slower than one of the other methods for one substrate. Comparing bait species between the three methods, Quercus ilex was the most attractive bait for P. cinnamomi, particularly in the CPSM method. The choice of protocol affected the isolation associated with each bait type. Overall, the multiple bait system used by CPSM was shown to provide the most sensitive and reliable detection of Phytophthora species from soil samples.info:eu-repo/semantics/publishedVersio
    • …
    corecore