Implementation of a X-mode multichannel edge density profile reflectometer for the new ICRH antenna on ASDEX Upgrade

Ion cyclotron resonance heating (ICRH) is one of the main heating mechanisms for nuclear fusion plas- mas. However, studying the effects of ICRH operation, such as power coupling efficiency and convective transport, requires the measurement of the local edge plasma density profiles. Two new three-strap an- tennas were designed to reduce tungsten impurity release during operation, and installed on ASDEX Upgrade. One of these ICRH antennas embedded ten pairs of small microwave pyramidal horn anten- nas. In this thesis, a new multichannel X-mode microwave reflectometry diagnostic was developed to use these embedded antennas to simultaneously measure the edge electron density profiles in front of the bottom, middle and top regions of the radiating surface of the ICRH antenna. Microwave reflectome- try is a radar technique that measures the round trip delay of probing waves that are reflected at specific cutoff layers, depending on the probing wave frequency, plasma density and local magnetic field. This diagnostic uses a coherent heterodyne quadrature detection architecture and probes the plasma in the range 40-68 GHz to measure plasma edge electron densities up to 2×1019 m-3, with magnetic fields between 1.85 T and 2.7 T, and a repetition interval as low as 25 μs. This work details the implementa- tion and commissioning of the diagnostic, including the calibration of the microwave hardware and the analysis of the raw reflectometry measurements. We study the automatic initialization of the X-mode upper cutoff measurement, which is the main source of error in X-mode density profile reconstruction. Two first fringe estimation algorithms were developed: one based on amplitude and spectral information and another using a neural network model to recognize the first fringe location from spectrogram data. Kalman filters are used to improve radial measurement uncertainty to less than 1 cm. To validate the diagnostic, we compared the density profile measurements with other electron density diagnostics on ASDEX Upgrade, and observed typical plasma phenomena like the L-H transition and ELM activity. The experimental density profile results were used to corroborate ICRH power coupling simulations under different gas puffing conditions and to observe poloidal convective transport during ICRH operation

Progress from ASDEX Upgrade experiments in preparing the physics basis of ITER operation and DEMO scenario development

An overview of recent results obtained at the tokamak ASDEX Upgrade (AUG) is given. A work flow for predictive profile modelling of AUG discharges was established which is able to reproduce experimental H-mode plasma profiles based on engineering parameters only. In the plasma center, theoretical predictions on plasma current redistribution by a dynamo effect were confirmed experimentally. For core transport, the stabilizing effect of fast ion distributions on turbulent transport is shown to be important to explain the core isotope effect and improves the description of hollow low-Z impurity profiles. The L–H power threshold of hydrogen plasmas is not affected by small helium admixtures and it increases continuously from the deuterium to the hydrogen level when the hydrogen concentration is raised from 0 to 100%. One focus of recent campaigns was the search for a fusion relevant integrated plasma scenario without large edge localised modes (ELMs). Results from six different ELM-free confinement regimes are compared with respect to reactor relevance: ELM suppression by magnetic perturbation coils could be attributed to toroidally asymmetric turbulent fluctuations in the vicinity of the separatrix. Stable improved confinement mode plasma phases with a detached inner divertor were obtained using a feedback control of the plasma β. The enhanced Dα H-mode regime was extended to higher heating power by feedback controlled radiative cooling with argon. The quasi-coherent exhaust regime was developed into an integrated scenario at high heating power and energy confinement, with a detached divertor and without large ELMs. Small ELMs close to the separatrix lead to peeling-ballooning stability and quasi continuous power exhaust. Helium beam density fluctuation measurements confirm that transport close to the separatrix is important to achieve the different ELM-free regimes. Based on separatrix plasma parameters and interchange-drift-Alfvén turbulence, an analytic model was derived that reproduces the experimentally found important operational boundaries of the density limit and between L- and H-mode confinement. Feedback control for the X-point radiator (XPR) position was established as an important element for divertor detachment control. Stable and detached ELM-free phases with H-mode confinement quality were obtained when the XPR was moved 10 cm above the X-point. Investigations of the plasma in the future flexible snow-flake divertor of AUG by means of first SOLPS-ITER simulations with drifts activated predict beneficial detachment properties and the activation of an additional strike point by the drifts.This work has been carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014–2018 and 2019–2020 under Grant Agreement No. 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission.Peer Reviewed"Article signat per més de 50 autors/es: U. Stroth, D. Aguiam, E. Alessi, C. Angioni, N. Arden, R. Arredondo Parra, V. Artigues, O. Asunta, M. Balden, V. Bandaru, A. Banon-Navarro, K. Behler, A. Bergmann, M. Bergmann, J. Bernardo, M. Bernert, A. Biancalani, R. Bielajew, R. Bilato, G. Birkenmeier, T. Blanken, V. Bobkov, A. Bock, T. Body, T. Bolzonella, N. Bonanomi, A. Bortolon, B. Böswirth, C. Bottereau, A. Bottino, H. van den Brand, M. Brenzke, S. Brezinsek, D. Brida, F. Brochard, C. Bruhn, J. Buchanan, A. Buhler, A. Burckhart, Y. Camenen, B. Cannas, P. Cano Megias, D. Carlton, M. Carr, P. Carvalho, C. Castaldo, M. Cavedon, C. Cazzaniga, C. Challis, A. Chankin, C. Cianfarani, F. Clairet, S. Coda, R. Coelho, J.W. Coenen, L. Colas, G. Conway, S. Costea, D. Coster, T. Cote, A.J. Creely, G. Croci, D.J. Cruz Zabala, G. Cseh, A. Czarnecka, I. Cziegler, O. D'Arcangelo, A. Dal Molin, P. David, C. Day, M. de Baar, P. de Marné, R. Delogu, S. Denk, P. Denner, A. Di Siena, J.J. Dominguez Palacios Durán, D. Dunai, A. Drenik, M. Dreval, R. Drube, M. Dunne, B.P. Duval, R. Dux, T. Eich, S. Elgeti, A. Encheva, K. Engelhardt, B. Erdös, I. Erofeev, B. Esposito, E. Fable, M. Faitsch, U. Fantz, M. Farnik, H. Faugel, F. Felici, O. Ficker, S. Fietz, A. Figueredo, R. Fischer, O. Ford, L. Frassinetti, M. Fröschle, G. Fuchert, J.C. Fuchs, H. Fünfgelder, S. Futatani, K. Galazka, J. Galdon-Quiroga, D. Gallart Escolà, A. Gallo10, Y. Gao11, S. Garavaglia3, M. Garcia Muñoz16, B. Geiger21, L. Giannone1, S. Gibson32, L. Gil2, E. Giovannozzi18, S. Glöggler1, M. Gobbin8, J. Gonzalez Martin, T. Goodman, G. Gorini, T. Görler, D. Gradic, G. Granucci, A. Gräter, H. Greuner, M. Griener, M. Groth, A. Gude, L. Guimarais, S. Günter, G. Haas, A.H. Hakola, C. Ham, T. Happel, N. den Harder, G. Harrer, J. Harrison, V. Hauer, T. Hayward-Schneider, B. Heinemann, T. Hellsten, S. Henderson, P. Hennequin, A. Herrmann, E. Heyn, F. Hitzler, J. Hobirk, K. Höfler, J.H. Holm, M. Hölzl, C. Hopf, L. Horvath, T. Höschen, A. Houben, A. Hubbard, A. Huber, K. Hunger, V. Igochine, M. Iliasova, T. Ilkei, K. Insulander Björk, C. Ionita-Schrittwieser, I. Ivanova-Stanik, W. Jacob, N. Jaksic, F. Janky, A. Jansen van Vuuren, A. Jardin, F. Jaulmes, F. Jenko, T. Jensen, E. Joffrin, A. Kallenbach, S. Kálvin, M. Kantor, A. Kappatou, O. Kardaun, J. Karhunen4, C.-P. Käsemann, S. Kasilov, A. Kendl, W. Kernbichler, E. Khilkevitch, A. Kirk, S. Kjer Hansen, V. Klevarova, G. Kocsis, M. Koleva, M. Komm, M. Kong, A. Krämer-Flecken, K. Krieger, A. Krivska, O. Kudlacek, T. Kurki-Suonio, B. Kurzan, B. Labit, K. Lackner, F. Laggner, A. Lahtinen, P.T. Lang, P. Lauber, N. Leuthold, L. Li, J. Likonen, O. Linder, B. Lipschultz, Y. Liu, A. Lohs, Z. Lu, T. Luda di Cortemiglia, N.C. Luhmann, T. Lunt, A. Lyssoivan, T. Maceina, J. Madsen, A. Magnanimo, H. Maier, J. Mailloux, R. Maingi, O. Maj, E. Maljaars, P. Manas, A. Mancini, A. Manhard, P. Mantica, M. Mantsinen, P. Manz, M. Maraschek, C. Marchetto, L. Marrelli, P. Martin, A. Martitsch, F. Matos, M. Mayer, M.-L. Mayoral, D. Mazon, P.J. McCarthy, R. McDermott, R. Merkel, A. Merle, D. Meshcheriakov, H. Meyer, D. Milanesio, P. Molina Cabrera, F. Monaco, M. Muraca, F. Nabais, V. Naulin, R. Nazikian, R.D. Nem, A. Nemes-Czopf, G. Neu, R. Neu, A.H. Nielsen, S.K. Nielsen, T. Nishizawa, M. Nocente, J.-M. Noterdaeme, I. Novikau, S. Nowak, M. Oberkofler, R. Ochoukov, J. Olsen, F. Orain, F. Palermo, O. Pan, G. Papp, I. Paradela Perez, A. Pau, G. Pautasso, C. Paz-Soldan, P. Petersson, P. Piovesan, C. Piron, U. Plank, B. Plaum, B. Plöck, V. Plyusnin, G. Pokol, E. Poli, L. Porte, T. Pütterich, M. Ramisch, J. Rasmussen, G. Ratta, S. Ratynskaia, G. Raupp, D. Réfy, M. Reich1, F. Reimold, D. Reiser, M. Reisner, D. Reiter, T. Ribeiro, R. Riedl, J. Riesch, D. Rittich, J.F. Rivero Rodriguez, G. Rocchi, P. Rodriguez-Fernandez, M. Rodriguez-Ramos, V. Rohde, G. Ronchi, A. Ross, M. Rott, M. Rubel, D.A. Ryan, F. Ryter, S. Saarelma, M. Salewski, A. Salmi, O. Samoylov, L. Sanchis Sanchez, J. Santos, O. Sauter, G. Schall, K. Schlüter, K. Schmid, O. Schmitz, P.A. Schneider, R. Schrittwieser, M. Schubert, C. Schuster, T. Schwarz-Selinger, J. Schweinzer, E. Seliunin, A. Shabbir, A. Shalpegin, S. Sharapov, U. Sheikh, A. Shevelev, G. Sias, M. Siccinio, B. Sieglin, A. Sigalov, A. Silva, C. Silva, D. Silvagni, J. Simpson, S. Sipilä, E. Smigelskis, A. Snicker, E. Solano, C. Sommariva, C. Sozzi, G. Spizzo, M. Spolaore, A. Stegmeir, M. Stejner, J. Stober, E. Strumberge1, G. Suarez Lopez, H.-J. Sun, W. Suttrop, E. Sytova, T. Szepesi, B. Tál, T. Tala, G. Tardini, M. Tardocchi, D. Terranova, M. Teschke, E. Thorén, W. Tierens, D. Told, W. Treutterer, G. Trevisan, E. Trier, M. Tripský, M. Usoltceva, M. Valisa, M. Valovic, M. van Zeeland, F. Vannini, B. Vanovac, P. Varela, S. Varoutis, N. Vianello, J. Vicente, G. Verdoolaege, T. Vierle, E. Viezzer, I. Voitsekhovitch, U. von Toussaint, D. Wagner, X. Wang, M. Weiland, A.E. White, M. Willensdorfer, B. Wiringer, M. Wischmeier, R. Wolf, E. Wolfrum, Q. Yang, Q. Yu, R. Zagórski, I. Zammuto, T. Zehetbauer, W. Zhang, W. Zholobenko, M. Zilker, A. Zito, H. Zohm, S. Zoletnik and the EUROfusion MST1 Team "Postprint (published version

Fabrication of a MEMS micromirror based on bulk silicon micromachining combined with grayscale lithography

A 1D MEMS (Micro-Electro-Mechanical Systems) mirror for LiDAR applications, based on vertically asymmetric comb-drive electrostatic actuators, is presented in this work employing a novel fabrication process. This novel micromachining process combines typical SOI-based bulk micromachining and grayscale lithography, enabling the fabrication of combs actuators with asymmetric heights using a single lithography step in the active layer. With this technique, the fabrication process is simplified, and the overall costs are reduced since the number of required lithography steps decrease. The fabricated mirrors present self-aligned electrodes with a 2.8 mu m gap and asymmetric heights of the movable and the fixed electrodes of 20 mu m and 50 mu m, respectively. These asymmetric actuators are an essential feature for the operation mode of this device, enabling both in resonant and static mode operation. A mirror field of view (FOV) of 54 degrees at 838 Hz was achieved under low-pressure, when resonantly operated, and a FOV of 0.8 degrees in the static mode.This work was supported by the European Structural and Investment Funds in the FEDER Component through the Operational Competitiveness and Internationalization Programme (COMPETE 2020) under Project 037902 (POCI-01-0247-FEDER-037902). The work of Carlos Ferreira was supported by the Fundacao para a Ciencia e Tecnologia (FCT) under Grant PD/BDE/135102/2017. Subject Editor M. Rais-Zadeh

Implementation of the new multichannel X-mode edge density profile reflectometer for the ICRF antenna on ASDEX Upgrade

A new multichannel frequency modulated continuous-wave reflectometry diagnostic has been successfully installed and commissioned on ASDEX Upgrade to measure the plasma edge electron density profile evolution in front of the Ion Cyclotron Range of Frequencies (ICRF) antenna. The design of the new three-strap ICRF antenna integrates ten pairs (sending and receiving) of microwave reflectometry antennas. The multichannel reflectometer can use three of these to measure the edge electron density profiles up to 2 x 10(19) m(-3), at different poloidal locations, allowing the direct study of the local plasma layers in front of the ICRF antenna. ICRF power coupling, operational effects, and poloidal variations of the plasma density profile can be consistently studied for the first time. In this work the diagnostic hardware architecture is described and the obtained density profile measurements were used to track outer radial plasma position and plasma shape

Recent progress on improving ICRF coupling and reducing RF-specific impurities in ASDEX Upgrade

The recent scientific research on ASDEX Upgrade (AUG) has greatly advanced solutions to two issues of Radio Frequency (RF) heating in the Ion Cyclotron Range of Frequencies (ICRF): (a) the coupling of ICRF power to the plasma is significantly improved by density tailoring with local gas puffing; (b) the release of RF-specific impurities is significantly reduced by minimizing the RF near field with 3-strap antennas. This paper summarizes the applied methods and reviews the associated achievements

Testing procedure of Friction Stir Welding defects using an eddy currents planar coil probe

Operation procedure to test Friction Stir Welding defects using the planar probe

Design of Arbitrary Magnetic Patterns on Magnetic Polymer Composite Objects: A Finite Element Modelling Tool

Magnetic sensor systems integrate a sensing element and magnetic field generators to determine their relative position or to measure movement. Typically, the magnetic fields are produced by permanent magnets, which have high intensity but are hard to machine into custom shapes. However, novel solutions using magnetic polymer composites (MPCs) have emerged as field generators due to their low cost, weight and patterning freedom. Here, we present a finite element model developed in COMSOL Multiphysics that allows the design of complex magnetization patterns on these polymer composites, taking into account the geometries of the parts and the magnetic properties of the materials employed. The model, together with the characterization protocol of the materials, has proved to be capable of predicting the magnetization of polymer composites at different temperatures. In addition, the model incorporates the properties of the magnets used during the magnetization process, such as the size, shape and magnetization, as well as the properties of the surrounding elements. This new model facilitates the design of new polymeric parts with complex shapes and magnetization patterns that can be employed as field generators in magnetic sensing systems

Assessing tolerances in direct write laser grayscale lithography and reactive ion etching pattern transfer for fabrication of 2.5D Si master molds

Direct Write Laser (DWL) Grayscale (GS) lithography has gathered attention as a versatile technological solution to fabricate arbitrary and complex 2.5D structures in photoresist (PR). In combination with Reactive Ion Etching (RIE), DWL GS can enable the fabrication of 2.5D micro-structured silicon substrates to be used as molds in high-precision replication processes. To this end, typically, a multilevel pattern is first defined in a low contrast PR and then transferred to the Si substrate via anisotropic RIE. The uniformity and selectivity of the etching process to the PR and substrate materials will define the dimensions of the 2.5D structures in the substrate. However, while there have been numerous examples of etched shapes in Si using this strategy, the wafer scale dimensional variations for etched Si molds fabricated via DWL GS and RIE have not been reported so far. In this work, we present a wafer-scale and wafer-to-wafer analysis of the dimensional variations in the fabrication process of Si molds with 2.5D 100-μm deep cavities using DWL GS lithography and RIE. The dimensional variations and deviations were characterized along each process step over several wafers. The final Si etched shapes consisting of microlens array cavities showed a maximum relative deviation of 10.35% with respect to the intended shape design with a curvature radius variation up to ∼5%, demonstrating this process potential for arbitrary 2.5D Si mold fabrication

Plasma edge modelling with ICRF coupling

The physics of Radio-Frequency (RF) wave heating in the Ion Cyclotron Range of Frequencies (ICRF) in the core plasmas of fusion devices are relatively well understood while those in the Scrape-Off Layer (SOL) remain still unresolved. This paper is dedicated to study the ICRF interactions with the plasma edge, mainly from the theoretical and numerical point of view, in particular with the 3D edge plasma fluid and neutral transport code EMC3-EIRENE and various wave codes. Here emphasis is given to the improvement of ICRF coupling with local gas puffing and to the ICRF induced density convection in the SOL