Static internal performance of a single-engine onaxisymmetric-nozzle vaned-thrust-reverser design with thrust modulation capabilities

An investigation has been conducted at wind-off conditions in the stati-test facility of the Langley 16-Foot Transonic Tunnel. The tests were conducted on a single-engine reverser configuration with partial and full reverse-thrust modulation capabilities. The reverser design had four ports with equal areas. These ports were angled outboard 30 deg from the vertical impart of a splay angle to the reverse exhaust flow. This splaying of reverser flow was intended to prevent impingement of exhaust flow on empennage surfaces and to help avoid inlet reingestion of exhaust gas when the reverser is integrated into an actual airplane configuration. External vane boxes were located directly over each of the four ports to provide variation of reverser efflux angle from 140 deg to 26 deg (measured forward from the horizontal reference axis). The reverser model was tested with both a butterfly-type inner door and an internal slider door to provide area control for each individual port. In addition, main nozzle throat area and vector angle were varied to examine various methods of modulating thrust levels. Other model variables included vane box configuration (four or six vanes per box), orientation of external vane boxes with respect to internal port walls (splay angle shims), and vane box sideplates. Nozzle pressure ratio was varied from 2.0 approximately 7.0

High-density support matrices: Key to the deep borehole disposal of spent nuclear fuel

Deep (4–5 km) boreholes are emerging as a safe, secure, environmentally sound and potentially cost-effective option for disposal of high-level radioactive wastes, including plutonium. One reason this option has not been widely accepted for spent fuel is because stacking the containers in a borehole could create load stresses threatening their integrity with potential for releasing highly mobile radionuclides like 129I before the borehole is filled and sealed. This problem can be overcome by using novel high-density support matrices deployed as fine metal shot along with the containers. Temperature distributions in and around the disposal are modelled to show how decay heat from the fuel can melt the shot within weeks of disposal to give a dense liquid in which the containers are almost weightless. Finally, within a few decades, this liquid will cool and solidify, entombing the waste containers in a base metal sarcophagus sealed into the host rock

Experimental and analytical results of tangential blowing applied to a subsonic V/STOL inlet

Engine inlets for subsonic V/STOL aircraft must operate over a wide range of conditions without internal flow separation. Experimental and analytical investigations were conducted to evaluate the effectiveness of tangential blowing to maintain attached flow to high angles of attack. The inlet had a relatively thin lip with a blowing slot located either on the lip or in the diffuser. The height and width of these slots was varied. Experimentally determined flow separation boundaries showed that lip blowing achieved higher angle of attack capability than diffuser blowing. This capability was achieved with the largest slot circumferential extent and either of the two slot heights. Predicted (analytical) separation boundaries showed good agreement except at the highest angles of attack

Fracture of a viscous liquid

When a viscous liquid hits a pool of liquid of same nature, the impact region is hollowed by the shock. Its bottom becomes extremely sharp if increasing the impact velocity, and we report that the curvature at that place increases exponentially with the flow velocity, in agreement with a theory by Jeong and Moffatt. Such a law defines a characteristic velocity for the collapse of the tip, which explains both the cusp-like shape of this region, and the instability of the cusp if increasing (slightly) the impact velocity. Then, a film of the upper phase is entrained inside the pool. We characterize the critical velocity of entrainment of this phase and compare our results with recent predictions by Eggers

Flight Acoustic Testing and For the Rotorcraft Noise Data Acquisition Model (RNM)

Two acoustic flight tests have been conducted on a remote test range at Eglin Air Force Base in the panhandle of Florida. The first was the "Acoustics Week" flight test conducted in September 2003. The second was the NASA Heavy Lift Rotorcraft Acoustics Flight Test conducted in October-November 2005. Benchmark acoustic databases were obtained for a number of rotorcraft and limited fixed wing vehicles for a variety of flight conditions. The databases are important for validation of acoustic prediction programs such as the Rotorcraft Noise Model (RNM), as well as for the development of low noise flight procedures and for environmental impact assessments. An overview of RNM capabilities and a detailed description of the RNM/ART (Acoustic Repropagation Technique) process are presented. The RNM/ART process is demonstrated using measured acoustic data for the MD600N. The RNM predictions for a level flyover speed sweep show the highest SEL noise levels on the flight track centerline occurred at the slowest vehicle speeds. At these slower speeds, broadband noise content is elevated compared to noise levels obtained at the higher speeds. A descent angle sweep shows that, in general, ground noise levels increased with increasing descent rates. Vehicle orientation in addition to vehicle position was found to significantly affect the RNM/ART creation of source noise semi-spheres for vehicles with highly directional noise characteristics and only mildly affect those with weak acoustic directionality. Based on these findings, modifications are proposed for RNM/ART to more accurately define vehicle and rotor orientation

CTQ 839: Candidate for the Smallest Projected Separation Binary Quasar

We report the discovery of the new double quasar CTQ 839. This B = 18.3, radio quiet quasar pair is separated by 2.1" in BRIH filters with magnitude differences of delta m_B = 2.5, delta m_R = delta m_I = 1.9, and delta m_H = 2.3. Spectral observations reveal both components to be z = 2.24 quasars, with relative redshifts that agree at the 100 km/s level, but exhibit pronounced differences in the equivalent widths of related emission features, as well as an enhancement of blue continuum flux in the brighter component longward of the Ly alpha emission feature. In general, similar redshift double quasars can be the result of a physical binary pair, or a single quasar multiply imaged by gravitational lensing. Empirical PSF subtraction of R and H band images of CTQ 839 reveal no indication of a lensing galaxy, and place a detection limit of R = 22.5 and H = 17.4 for a third component in the system. For an Einstein-de Sitter cosmology and SIS model, the R band detection limit constrains the characteristics of any lensing galaxy to z_lens >= 1 with a corresponding luminosity of L >~ 5 L_*, while an analysis based on the redshift probability distribution for the lensing galaxy argues against the existence of a z_lens >~ 1 lens at the 2 sigma level. A similar analysis for a Lambda dominated cosmology, however, does not significantly constrain the existence of any lensing galaxy. The broadband flux differences, spectral dissimilarities, and failure to detect a lensing galaxy make the lensing hypothesis for CTQ 839 unlikely. The similar redshifts of the two components would then argue for a physical quasar binary. At a projected separation of 8.3/h kpc (Omega_matter = 1), CTQ 839 would be the smallest projected separation binary quasar currently known.Comment: Latex, 23 pages including 5 ps figures; accepted for publication in A

Influence of extended dynamics on phase transitions in a driven lattice gas

Monte Carlo simulations and dynamical mean-field approximations are performed to study the phase transition in a driven lattice gas with nearest-neighbor exclusion on a square lattice. A slight extension of the microscopic dynamics with allowing the next-nearest-neighbor hops results in dramatic changes. Instead of the phase separation into high- and low-density regions in the stationary state the system exhibits a continuous transition belonging to the Ising universality class for any driving. The relevant features of phase diagram are reproduced by an improved mean-field analysis.Comment: 3 pages, 3 figure

A Search for Stars of Very Low Metal Abundance. VI. Detailed Abundances of 313 Metal-Poor Stars

We present radial velocities, equivalent widths, model atmosphere parameters, and abundances or upper limits for 53 species of 48 elements derived from high resolution optical spectroscopy of 313 metal-poor stars. A majority of these stars were selected from the metal-poor candidates of the HK Survey of Beers, Preston, and Shectman. We derive detailed abundances for 61% of these stars for the first time. Spectra were obtained during a 10-year observing campaign using the Magellan Inamori Kyocera Echelle spectrograph on the Magellan Telescopes at Las Campanas Observatory, the Robert G. Tull Coude Spectrograph on the Harlan J. Smith Telescope at McDonald Observatory, and the High Resolution Spectrograph on the Hobby-Eberly Telescope at McDonald Observatory. We perform a standard LTE abundance analysis using MARCS model atmospheres, and we apply line-by-line statistical corrections to minimize systematic abundance differences arising when different sets of lines are available for analysis. We identify several abundance correlations with effective temperature. A comparison with previous abundance analyses reveals significant differences in stellar parameters, which we investigate in detail. Our metallicities are, on average, lower by approx. 0.25 dex for red giants and approx. 0.04 dex for subgiants. Our sample contains 19 stars with [Fe/H] < -3.5, 84 stars with [Fe/H] < -3.0, and 210 stars with [Fe/H] < -2.5. Detailed abundances are presented here or elsewhere for 91% of the 209 stars with [Fe/H] < -2.5 as estimated from medium resolution spectroscopy by Beers, Preston, and Shectman. We will discuss the interpretation of these abundances in subsequent papers.Comment: Accepted for publication in the Astronomical Journal. 60 pages, 59 figures, 18 tables. Machine-readable versions of the long tables can be found in the ancillary data file