Optimization of modular wiring harnesses by means of regression models for temperature prediction of wire bundles

Automotive wiring harnesses have become heavier and more complex due to their increasing number of electrical components. It is now desired to reduce their mass of copper. For this purpose, experimentation can be partially replaced by simulation, but it is still impossible to exhaustively simulate all of the combinations of modular wiring harness. This proposed approach consists of carrying out simulations using the FEM method and using their results to create regression models. Polynomial formulae can give the same information as simulations within a clearly reduced time and satisfying accuracy. An optimization algorithm introduced in this study will use them to assign new cable cross-sections of harnesses considering their currents and the ambient temperature.Postprint (author's final draft

Custom integer optimization method for wire bundle dimensioning

Automotive wiring harnesses have gained weight and complexity through the last decades due to the increasing number of electrical components, which has raised the interest on its weight optimization. For this purpose, it is essential to know at least the maximum amount of steady current that either single wires or bundles can carry. However, the large amount of combinations of the customer-speci¿c wire harnesses makes it impossible to exhaustively simulate all of the combinations that would allow for a reliable analysis and optimization of the network. The proposed approach consists of achieving accurate predictions of the wire thermal behaviour using fast on-line polynomial functions, which have been created as regression models using data from off-line worst-case ¿nite element sim- ulations. These regression models provide good accuracy for the critical dimensions of wire bundles in a much shorter time than simulations, so that they can be used on-line in optimiza- tion algorithms. Two different approaches of optimization are presented here in order to assign discrete values of available wire cross-section to the wire bundles: The ¿rst one uses integer linear programming, and the second one consists of a recently created custom algorithm whose objective is to reduce the computation time of the integer linear programming approach. This latter objective is satisfactorily accomplished. Results of both optimization approaches are validated by means of ¿nal ¿nite element simulations, and they promisingly ful¿ll the objectives of this study.Peer ReviewedPostprint (author's final draft

Evaluating satisfaction with teaching innovation, its relationship to academic performance and the application of a video-based microlearning

Aim: To develop and validate a questionnaire to assess satisfaction with teaching innovation, assess the student satisfaction with a video-based microlearning intervention in its video-based modality and to verify its impact on academic performance. Design: A descriptive cross-sectional study was conducted. The study used the COSMIN checklist for studies on measurement instruments. Methods: One hundred and ten nursing students from Salus Infirmorum University Centre (Andalusia, Spain) participated in the study. The items of the instrument were designed based on a literature review and its validity and stability were analysed. After that, 6 weeks of video-based microlearning intervention were implemented. Then students were asked to fill the satisfaction questionnaire and then took the subject exam. Results: The resulting questionnaire consisted of 5 items with only one dimension. The questionnaire showed good validity and reliability. A direct correlation was observed between satisfaction with the video-based microlearning intervention and the marks of the subject exam.11 página

RICORS2040 : The need for collaborative research in chronic kidney disease

Chronic kidney disease (CKD) is a silent and poorly known killer. The current concept of CKD is relatively young and uptake by the public, physicians and health authorities is not widespread. Physicians still confuse CKD with chronic kidney insufficiency or failure. For the wider public and health authorities, CKD evokes kidney replacement therapy (KRT). In Spain, the prevalence of KRT is 0.13%. Thus health authorities may consider CKD a non-issue: very few persons eventually need KRT and, for those in whom kidneys fail, the problem is 'solved' by dialysis or kidney transplantation. However, KRT is the tip of the iceberg in the burden of CKD. The main burden of CKD is accelerated ageing and premature death. The cut-off points for kidney function and kidney damage indexes that define CKD also mark an increased risk for all-cause premature death. CKD is the most prevalent risk factor for lethal coronavirus disease 2019 (COVID-19) and the factor that most increases the risk of death in COVID-19, after old age. Men and women undergoing KRT still have an annual mortality that is 10- to 100-fold higher than similar-age peers, and life expectancy is shortened by ~40 years for young persons on dialysis and by 15 years for young persons with a functioning kidney graft. CKD is expected to become the fifth greatest global cause of death by 2040 and the second greatest cause of death in Spain before the end of the century, a time when one in four Spaniards will have CKD. However, by 2022, CKD will become the only top-15 global predicted cause of death that is not supported by a dedicated well-funded Centres for Biomedical Research (CIBER) network structure in Spain. Realizing the underestimation of the CKD burden of disease by health authorities, the Decade of the Kidney initiative for 2020-2030 was launched by the American Association of Kidney Patients and the European Kidney Health Alliance. Leading Spanish kidney researchers grouped in the kidney collaborative research network Red de Investigación Renal have now applied for the Redes de Investigación Cooperativa Orientadas a Resultados en Salud (RICORS) call for collaborative research in Spain with the support of the Spanish Society of Nephrology, Federación Nacional de Asociaciones para la Lucha Contra las Enfermedades del Riñón and ONT: RICORS2040 aims to prevent the dire predictions for the global 2040 burden of CKD from becoming true

Colombian consensus recommendations for diagnosis, management and treatment of the infection by SARS-COV-2/ COVID-19 in health care facilities - Recommendations from expert´s group based and informed on evidence

La Asociación Colombiana de Infectología (ACIN) y el Instituto de Evaluación de Nuevas Tecnologías de la Salud (IETS) conformó un grupo de trabajo para desarrollar recomendaciones informadas y basadas en evidencia, por consenso de expertos para la atención, diagnóstico y manejo de casos de Covid 19. Estas guías son dirigidas al personal de salud y buscar dar recomendaciones en los ámbitos de la atención en salud de los casos de Covid-19, en el contexto nacional de Colombia

Métodos y técnicas de monitoreo y predicción temprana en los escenarios de riesgos socionaturales

Esta obra concentra los métodos y las técnicas fundamentales para el seguimiento y monitoreo de las dinámicas de los escenarios de riesgos socionaturales (geológicos e hidrometeorológicos) y tiene como objetivo general orientar, apoyar y acompañar a los directivos y operativos de protección civil en aterrizar las acciones y políticas públicas enfocadas a la gestión del riesgo local de desastre

Custom integer optimization method for wire bundle dimensioning

Automotive wiring harnesses have gained weight and complexity through the last decades due to the increasing number of electrical components, which has raised the interest on its weight optimization. For this purpose, it is essential to know at least the maximum amount of steady current that either single wires or bundles can carry. However, the large amount of combinations of the customer-speci¿c wire harnesses makes it impossible to exhaustively simulate all of the combinations that would allow for a reliable analysis and optimization of the network. The proposed approach consists of achieving accurate predictions of the wire thermal behaviour using fast on-line polynomial functions, which have been created as regression models using data from off-line worst-case ¿nite element sim- ulations. These regression models provide good accuracy for the critical dimensions of wire bundles in a much shorter time than simulations, so that they can be used on-line in optimiza- tion algorithms. Two different approaches of optimization are presented here in order to assign discrete values of available wire cross-section to the wire bundles: The ¿rst one uses integer linear programming, and the second one consists of a recently created custom algorithm whose objective is to reduce the computation time of the integer linear programming approach. This latter objective is satisfactorily accomplished. Results of both optimization approaches are validated by means of ¿nal ¿nite element simulations, and they promisingly ful¿ll the objectives of this study.Peer Reviewe