73,280 research outputs found
TumorML: Concept and requirements of an in silico cancer modelling markup language
This paper describes the initial groundwork carried out as part of the European Commission funded Transatlantic Tumor Model Repositories project, to develop a new markup language for computational cancer modelling, TumorML. In this paper we describe the motivations for such a language, arguing that current state-of-the-art biomodelling languages are not suited to the cancer modelling domain. We go on to describe the work that needs to be done to develop TumorML, the conceptual design, and a description of what existing markup languages will be used to compose the language specification
Effect of Deflagration-to-Detonation Transition on Pulse Detonation Engine Impulse
A detonation tube was built to study the deflagration-to-detonation transition (DDT) process and the impulse generated when combustion products exhaust into the atmosphere. The reactants used were stoichiometric ethylene and oxygen mixture with varying amounts of nitrogen present as diluent. The effects of varying the initial pressure from 30 kPa to 100 kPa were studied, as were the effects of varying the diluent concentration from 0% to 73.8% of the total mixture. Measurements were carried out with the tube free of obstacles and with three different obstacle configurations. Each obstacle configuration had a blockage ratio of 0.43.
It was found that the inclusion of obstacles dramatically lowered the DDT times and distances as compared to the no obstacle configuration. The obstacles were found to be particularly effective at inducing DDT in mixtures with low pressures and with high amounts of diluent. At the lowest pressures tested (30 kPa), obstacles reduced the DDT time and distance to approximately 12.5% of the no obstacle configuration values. The obstacles also allowed DDT to occur in mixture compositions of up to 60% diluent, while DDT was not achieved with more than 30% diluent in the no obstacle configuration.
A ballistic pendulum arrangement was utilized, enabling direct measurement of the impulse by measuring the tube's deflection. Additional means of impulse comparison consisted of integrating the pressure over the front wall of the tube. Impulse measurements were then compared with a theoretical model and were found to fit well cases that did not contain internal obstacles.
The inclusion of obstacles allowed DDT to occur in mixtures with high amounts of diluent where DDT was not observed to occur in the cases without obstacles. Roughly 100% more impulse was produced in the obstacle configurations as compared to the no obstacle configuration under these conditions. In instances where DDT occurred in the no obstacle configuration, the use of obstacle configurations lowered the impulse produced by an average of 25%. For cases where no obstacles were used and DDT occurred, the pressure derived impulses (pressure impulse) and impulses determined from the ballistic pendulum (ballistic impulses) are similar. For cases were obstacle configurations were tested, pressure impulses were more than 100% higher on average than ballistic impulses. This difference exists because the pressure model neglects drag due to the obstacle configurations
Recommended from our members
Application of thermoelectric aging models to polymeric insulation in cable geometry
The life expressions of models of insulation ageing are functions of temperature and field as well as material parameters. A methodology is presented that allows these models to be applied to a cable geometry in which there is a radial variation of both field and temperature. In this way material parameters can be extracted from cable data. The methodology is illustrated using one such model and the parameters deduced from cable failure distributions are compared with those obtained for thin films. This comparison allows conclusions to be drawn about how the ageing process affects specimens of the same material with different volumes
Patient safety indicators for England from hospital administrative data: case-control analysis and comparison with US data
This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.The Healthcare Commission received a small grant from the Health and Social Care Information Centre to support the initial recoding work
Recommended from our members
Application of polymer ageing models to power cables
Ageing models have been developed to predict the lifetime of polymeric insulation subject to electro-thermal stresses. We present here a method for applying the models to situations in which the field is not constant over the whole specimen, as for cable geometry. The method has been applied to characteristic lifetime data from AC ageing experiments on cables. The results are presented, and the effect of insulation volume upon the model parameters is discussed
Evaluation of Deep Learning based Pose Estimation for Sign Language Recognition
Human body pose estimation and hand detection are two important tasks for
systems that perform computer vision-based sign language recognition(SLR).
However, both tasks are challenging, especially when the input is color videos,
with no depth information. Many algorithms have been proposed in the literature
for these tasks, and some of the most successful recent algorithms are based on
deep learning. In this paper, we introduce a dataset for human pose estimation
for SLR domain. We evaluate the performance of two deep learning based pose
estimation methods, by performing user-independent experiments on our dataset.
We also perform transfer learning, and we obtain results that demonstrate that
transfer learning can improve pose estimation accuracy. The dataset and results
from these methods can create a useful baseline for future works
- ā¦