Auger recombination in quantum-well InGaAsP heterostructure lasers

Interband nonradiative Auger recombination in quantum-well InGaAsP/InP heterostructure lasers has been calculated. It is found that the Auger rate is much reduced in the quasi two-dimensional quantum-well lasers. This suggests that the temperature sensitivity of quantum-well InGaAsP lasers is much less than ordinary structures with much higher values of T0at around room temperatures

Analysis And Performance Of A Picosecond Dye Laser Amplifier Chain

Design considerations are discussed for a simple, easy to use and relatively efficient high gain dye laser amplifier chain for CW mode-locked dye lasers. The amplifier boosts the output of a synchronously mode-locked dye laser to obtain ≈005 mj, ≤ 1 psec pulses over a ≈ 400 Å bandwidth. These pulses are suitable for efficient Raman Shifting, frequency mixing and continuum generation to vastly extend the spectral range of the system. Our amplifier is pumped by a frequency doubled Nd:YAG oscillator only, which longitudinally pumps three identical brewster cells with the same flowing dye solution in each. Contrary to popular belief, high small signal gains (≥ 105) are easily attained in a single stage with longitudinal pumping, with better beam homogeneity and easier alignment than transverse pumping. Gain saturation measurements are presented which agree well with calculations. Factors which relax the pump timing sensitivity are examined. The importance of gain saturation for both efficient amplification and for amplitude stability is also discussed. The need for isolated amplifier stages is stressed and optimal amplifier cell areas for a given stage are calculated

On the linewidth enhancement factor alpha in semiconductor injection lasers

A simple model for the linewidth enhancement factor alpha and its frequency dependence in semiconductor lasers is presented. Calculations based on this model are in reasonable agreement with experimental results

A New Layer Casting System for Ceramic Laser Rapid Prototyping Apparatus

In the existing Ceramic Laser Fusion system, slurry is fed on the high temperature surface of the green part; therefore, a part of water infiltrates into the green block and vaporizes before the process of layer casting. As a result, the slurry viscosity rises gradually; the quality of the layer surface is not uniform, and the green part density is uneven. The aim of present study is to develop a new layer casting system which can solve the problems mentioned above to obtain a green part with uniform surface quality and density, and to shorten the time-taken of part fabrication. The first part of the paper illustrates the major requirements and parameters of a slurry distributor; the second part describes the integration of the slurry feeding device and layer casting system. The integrated system can feed slurry and cast thin layer simultaneously; consequently, the drawbacks of the existing system can be eliminated and the time-taken of the layer casting can be shortened. A variable-frequency drive (inverter) is used to control the motor speed. The relation between the frequency and the slurry delivery can be included in the process control program to adjust the quantity in accordance with the layer thickness; hence, the waste of the slurry can be reduced.Mechanical Engineerin

Graded collector heterojunction bipolar transistor

A graded collector heterojunction bipolar transistor is proposed. The graded collector improves device speed performance at high current densities by reducing the influence of the Kirk effect

Effect of spin-orbit interaction on heterojunction band discontinuities

The effect of spin-orbit interaction is included in the linear combination of atomic orbitals calculation of heterojunction band discontinuities. It is found that spin-orbit interaction is not negligible when the atomic number of the constituent atoms exceeds about 40. The effect of spin-orbit interaction as well as some interesting observations and their implications are briefly discussed

Internal photoemission from quantum well heterojunction superlattices by phononless free-carrier absorption

The possibility of phononless free-carrier absorption in quantum well heterojunction superlattices was investigated. Order of magnitude calculation showed that the absorption coefficient was significantly enhanced over the phonon-assisted process. Important aspects of the enhancement in the design of infrared photodetectors are discussed

Studies in upper and lower atmosphere coupling

The theoretical and data-analytic work on upper and lower atmosphere coupling performed under a NASA Headquarters contract during the period April 1978 to March 1979 are summarized. As such, this report is primarily devoted to an overview of various studies published and to be published under this contract. Individual study reports are collected as exhibits. Work performed under the subject contract are in the following four areas of upper-lower atmosphere coupling: (1) Magnetosphere-ionosphere electrodynamic coupling in the aurora; (2) Troposphere-thermosphere coupling; (3) Ionosphere-neutral-atmosphere coupling; and (4) Planetary wave dynamics in the middle atmosphere

The Characteristics and Applications of Ceramic Laser Fusion and Ceramic Laser Sintering

The aim of present study is to investigate the possible application of the ceramic parts which are fabricated with the process of Ceramic Laser Fusion or Ceramic Laser Sintering. The experimental results reveal: (1) CLF can lead to a reduction in the porosity of the ceramic part but also can induce micro-cracks. Therefore, this process cannot produce a part with the required strength by a post-process of infiltration; (2) CLS is capable of fabricating a ceramic part with high porosity. By adjusting the slurry formulation and varying the scanning energy, the open porosity can be over 90vol% of the total porosity. After a post-process of infiltration, the density can be increased to 95%; therefore, CLS can apply to produce a part with high strength. Because the high open porosity leads to a good permeability, the process of CLS is suitable for the fabrication of ceramic shell mold.Mechanical Engineerin