Velocity-space sensitivity of the time-of-flight neutron spectrometer at JET

The velocity-space sensitivities of fast-ion diagnostics are often described by so-called weight functions. Recently, we formulated weight functions showing the velocity-space sensitivity of the often dominant beam-target part of neutron energy spectra. These weight functions for neutron emission spectrometry (NES) are independent of the particular NES diagnostic. Here we apply these NES weight functions to the time-of-flight spectrometer TOFOR at JET. By taking the instrumental response function of TOFOR into account, we calculate time-of-flight NES weight functions that enable us to directly determine the velocity-space sensitivity of a given part of a measured time-of-flight spectrum from TOFOR

Relationship of edge localized mode burst times with divertor flux loop signal phase in JET

A phase relationship is identified between sequential edge localized modes (ELMs) occurrence times in a set of H-mode tokamak plasmas to the voltage measured in full flux azimuthal loops in the divertor region. We focus on plasmas in the Joint European Torus where a steady H-mode is sustained over several seconds, during which ELMs are observed in the Be II emission at the divertor. The ELMs analysed arise from intrinsic ELMing, in that there is no deliberate intent to control the ELMing process by external means. We use ELM timings derived from the Be II signal to perform direct time domain analysis of the full flux loop VLD2 and VLD3 signals, which provide a high cadence global measurement proportional to the voltage induced by changes in poloidal magnetic flux. Specifically, we examine how the time interval between pairs of successive ELMs is linked to the time-evolving phase of the full flux loop signals. Each ELM produces a clear early pulse in the full flux loop signals, whose peak time is used to condition our analysis. The arrival time of the following ELM, relative to this pulse, is found to fall into one of two categories: (i) prompt ELMs, which are directly paced by the initial response seen in the flux loop signals; and (ii) all other ELMs, which occur after the initial response of the full flux loop signals has decayed in amplitude. The times at which ELMs in category (ii) occur, relative to the first ELM of the pair, are clustered at times when the instantaneous phase of the full flux loop signal is close to its value at the time of the first ELM

Experimental raw data from FLIR A655CS thermographic camera

The upload data contents the thermal image video files from thermographic camera Flir A655SC. These data were used to measure and calculate temperature of sample according to suggested method.Name of data files / Front side temperature of the sample (thermocouple) , Celsius degree 1681 / 6101682 / 7551685 / 8961686 / 10161689 / 11331690 / 12521691 / 1351 1692 / 1473It is required to use FLIR ResearchIR software to observe and analyse data.THIS DATASET IS ARCHIVED AT DANS/EASY, BUT NOT ACCESSIBLE HERE. TO VIEW A LIST OF FILES AND ACCESS THE FILES IN THIS DATASET CLICK ON THE DOI-LINK ABOV

Data for: Test Results of Active Thermography Method for Plasma-Wall Interaction Studies on the КТМ Tokamak

File contains processed data from conducted experiment on the test bench for testing the suggested thermographic method.THIS DATASET IS ARCHIVED AT DANS/EASY, BUT NOT ACCESSIBLE HERE. TO VIEW A LIST OF FILES AND ACCESS THE FILES IN THIS DATASET CLICK ON THE DOI-LINK ABOV

First spectroscopic studies in the plasma-beam installation

This paper presents the results of spectroscopic measurements of plasma in a linear simulator of a plasma-beam installation (PBI) for conducting materials science research. For the first time, non-contact optical diagnostic methods were employed to measure the plasma parameters in the PBI. These measurements were allowed for the clarification of the PBI plasma parameters and the identification of transition zones in different operational modes. Analysis of the plasma emission spectrum enabled the identification of impurity spectral lines and the estimation of key plasma parameters under varying experimental conditions. The spectra were recorded using two optical spectrometers covering a wavelength range of 200–800 nm. The experimental conditions varied in terms of electron beam accelerating voltage (1–5 kV), working gas pressure (1–6 mTorr), and target bias voltage (from −500 to −100 V). The Boltzmann plot method and Stark broadening of the Balmer lines were used to estimate electron temperature and density. Based on the obtained spectroscopic data, the electron density and the electron temperature were determined. The methods described in this study are applicable to linear plasma devices

Impact of nitrogen seeding on confinement and power load control of a high-triangularity JET ELMy H-mode plasma with a metal wall

This paper reports the impact on confinement and power load of the high-shape 2.5MA ELMy H-mode scenario at JET of a change from an all carbon plasma facing components to an all metal wall. In preparation to this change, systematic studies of power load reduction and impact on confinement as a result of fuelling in combination with nitrogen seeding were carried out in JET-C and are compared to their counterpart in JET with a metallic wall. An unexpected and significant change is reported on the decrease of the pedestal confinement but is partially recovered with the injection of nitrogen.Comment: 30 pages, 16 figure