Control of Mammalian Cell Behaviour Through Mimicry of the Extracellular Matrix Environment

This chapter looks at the control of mammalian cell behaviour through mimicry of the extracellular matrix enviromen

Discovering Novel Small Molecule Compound for Prevention of Monoclonal Antibody Self-Association

Designing an antibody with the desired affinity to the antigen is challenging, often achieved by lengthening the hydrophobic CDRs, which can lead to aggregation and cause major hindrance to the development of successful biopharmaceutical products. Aggregation can cause immunogenicity, viscosity and stability issues affecting both the safety and quality of the product. As the hydrophobic residues on the CDR are required for direct binding to antigens, it is not always possible to substitute these residues for aggregation-reduction purposes. Therefore, discovery of specific excipients to prevent aggregation is highly desirable for formulation development. Here, we used a combination of in silico screening methods to identify aggregation-prone regions on an aggregation-prone therapeutic antibody. The most aggregation-prone region on the antibody was selected to conduct virtual screening of compounds that can bind to such regions and act as an aggregation breaker. The most promising excipient candidate was further studied alongside plain buffer formulations and formulations with trehalose using coarse-grained molecular dynamics (CGMD) simulations with MARTINI force field. Mean interaction value between two antibody molecules in each formulation was calculated based on 1024 replicates of 512 ns of such CGMD simulations. Corresponding formulations with an excipient:antibody ratio of 1:5 were compared experimentally by measuring the diffusion interaction parameter kD and accelerated stability studies. Although the compound with the highest affinity score did not show any additional protective effects compared with trehalose, this study proved using a combination of in silico tools can aid excipient design and formulation development

Evaluation of aggregate and silicone-oil counts in pre-filled siliconized syringes: An orthogonal study characterising the entire subvisible size range.

Characterisation of particulates in therapeutic monoclonal antibody (mAb) formulations is routinely extended to the sub-visible size-range (0.1–10 μm). Additionally, with the increased use of pre-filled syringes (PFS), particle differentiation is required between proteinaceous and non-proteinaceous particles such as silicone-oil droplets. Here, three orthogonal techniques: Raster Image Correlation Spectroscopy (RICS), Resonance Mass Measurements (RMM) and Micro-Flow Imaging (MFI), were evaluated with respect to their sub-visible particle measurement and characterisation capabilities. Particle formation in mAb PFS solutions was evaluated with increasing polysorbate-20 (PS-20) concentrations. All three techniques provided complementary but distinct information on protein aggregate and silicone-oil droplet presence. PS-20 limited the generation of mAb aggregates during agitation, while increasing the number of silicone-oil droplets (PS-20 concentration dependant). MFI and RMM revealed PS-20 lead to the formation of larger micron-sized droplets, with RICS revealing an increase in smaller sub-micron droplets. Subtle differences in data sets complicate the apparent correlation between silicone-oil sloughing and mAb aggregates’ generation. RICS (though the use of a specific dye) demonstrates an improved selectivity for mAb aggregates, a broader measurement size-range and smaller sample volume requirement. Thus, RICS is proposed to add value to the currently available particle measurement techniques and enable informed decisions during mAb formulation development

Insights into the influence of the cooling profile on the reconstitution times of amorphous lyophilized protein formulations

Lyophilized protein formulations must be reconstituted back into solution prior to patient administration and in this regard long reconstitution times are not ideal. The factors that govern reconstitution time remain poorly understood. The aim of this research was to understand the influence of the lyophilization cooling profile (including annealing) on the resulting cake structure and reconstitution time. Three protein formulations (BSA 50 mg/ml, BSA 200 mg/ml and IgG1 40 mg/ml, all in 7% w/v sucrose) were investigated after cooling at either 0.5 °C/min, or quench cooling with liquid nitrogen with/without annealing. Significantly longer reconstitution times were observed for the lower protein concentration formulations following quench cool. Porosity measurements found concomitant increases in the surface area of the porous cake structure but a reduction in total pore volume. We propose that slow reconstitution results from either closed pores or small pores impeding the penetration of water into the lyophilized cake

PLGA microcapsules with novel dimpled surfaces for pulmonary delivery of DNA

We describe the fabrication of DNA-loaded poly(lactic-co-glycolic acid) (PLGA) microcapsules with novel surface morphologies that will be of use in pulmonary delivery. Our approach was to examine surface morphology and DNA encapsulation efficiency as a function of primary emulsion stability; using two surfactant series based on hydrophile–lipophile balance and hydrophobe molecular weight. Hydrophilic non-ionic surfactants yielded the most stable water-in-dichloromethane emulsions (HLB values >8). These surfactants normally favor convex (o/w) interfacial curvatures and therefore this atypical behavior suggested a relatively high surfactant solvation in the dichloromethane ‘oil’ phase. This was consistent with the large fall in the glass transition temperature for microspheres prepared with Tween 20, which therefore efficiently penetrated the PLGA matrix and acted as a plasiticizer. Blends of Pluronic triblock copolymers performed poorly as water-in-dichloromethane emulsifiers, and were therefore used to generate hollow microspheres (‘microcapsules’) with low densities (0.24 g/cm3). Although the Pluronic-stabilized emulsions resulted in lower DNA loading (15–28%), microspheres (∼8�m) with novel dimpled surfaces were fabricated. The depth and definition of the dimples was greatest for triblock copolymers with high MW hydrophobe blocks. By cascade impaction, the geometric mean weight diameter of the microcapsules was 3.43�m, suggesting that they will be of interest as biodegradable pulmonary delivery vehicles

Engineering biodegradable polyester particles with specific drug targeting and drug release properties

Poly(lactic acid) (PLA) and poly(lactic-co-glycolic acid) (PLGA) microspheres and nanoparticles remain the focus of intensive research effort directed to the controlled release and in vivo localization of drugs. In recent years engineering approaches have been devised to create novel micro- and nano-particles which provide greater control over the drug release profile and present opportunities for drug targeting at the tissue and cellular levels. This has been possible with better understanding and manipulation of the fabrication and degradation processes, particularly emulsion-solvent extraction, and conjugation of polyesters with ligands or other polymers before or after particle formation. As a result, particle surface and internal porosity have been designed to meet criteria-facilitating passive targeting (e.g., for pulmonary delivery), modification of the drug release profile (e.g., attenuation of the burst release) and active targeting via ligand binding to specific cell receptors. It is now possible to envisage adventurous applications for polyester microparticles beyond their inherent role as biodegradable, controlled drug delivery vehicles. These may include drug delivery vehicles for the treatment of cerebral disease and tumor targeting, and codelivery of drugs in a pulsatile and/or time-delayed fashio