Morphological analysis of glass, carbon and glass/carbon fiber posts and bonding to self or dual-cured resin luting agents

OBJECTIVE: The aim of this study was to evaluate the morphology of glass (GF), carbon (CF) and glass/carbon (G/CF) fiber posts and their bond strength to self or dual-cured resin luting agents. MATERIAL AND METHODS: Morphological analysis of each post type was conducted under scanning electron microscopy (SEM). Bond strength was evaluated by microtensile test after bisecting the posts and re-bonding the two halves with the luting agents. Data were subjected to two-way ANOVA and Tukey's test (&#945;=0.05). Failure modes were evaluated under optical microscopy and SEM. RESULTS: GF presented wider fibers and higher amount of matrix than CF, and G/CF presented carbon fibers surrounded by glass fibers, and both involved by matrix. For CF and GF, the dual-cured material presented significantly higher (p<0.05) bond strength than the self-cured agent. For the dual agent, CF presented similar bond strength to GF (p>0.05), but higher than that of G/CF (p<0.05). For the self-cured agent, no significant differences (p>0.05) were detected, irrespective of the post type. For GF and G/CF, all failures were considered mixed, while a predominance of adhesive failures was detected for CF. CONCLUSION: The bonding between fiber posts and luting agents was affected by the type of fibers and polymerization mode of the cement. When no surface treatment of the post is performed, the bonding between glass fiber post and dual-cured agent seems to be more reliable

Pino de fibra de vidro anatômico: relato de caso

Introdução: Pinos pré-fabricados de fibra de vidro possuem boas propriedades mecânicas e estéticas. Porém, estes podem não se adaptar bem em canais amplos ou excessivamente cônicos, prejudicando sua retenção ao canal radicular. Uma alternativa para esta desvantagem é a utilização da técnica de pino anatômico. Objetivo: O objetivo do relato de caso foi apresentar a técnica de confecção de um pino fibra de vidro anatômico em dente anterior, com reduzido remanescente coronário e ampla embocadura do canal radicular. Relato de Caso: Paciente masculino, 49 anos, procurou atendimento odontológico com queixa da aparência estética de seus dentes anteriores superiores. Após remoção de uma coroa metalocerâmica e um pino-núcleo metálico fundido do elemento 12, foram confeccionados um pino de fibra de vidro anatômico, núcleo de preenchimento e coroa provisória. Foram realizadas as facetas em resina composta nos elementos 13, 11, 21, 22 e 23. Uma coroa de cerâmica reforçada por dissilicato de lítio (IPS e.max CAD, Ivoclar Vivadent) foi cimentada no elemento 12. Conclusões: Através da técnica pino de fibra de vidro anatômico, é possível reabilitar dentes anteriores tratados endodonticamente sem a utilização de pinos metálicos, apresentando bons resultados estéticos. Entretanto, uma condição oclusal dentro dos princípios de uma oclusão mutuamente protegida deve ser almejada para garantir longevidade da restauração

Influence of glass fiber posts and class III direct restorations on the resistance of anterior teeth

This study objectives to evaluate the fracture strength of upper central incisors (UCI) restored with composite resin (CR) in Class III cavities and endodontically treated teeth with or without glass fiber post (GFP), analyzing their failure mode. Sixty human UCI were randomly divided into four experimental groups: endodontically treated teeth without GFP (G1), endodontically treated teeth with GFP (G2), teeth with mesial/distal Class III cavities restored with CR without GFP (G3), and teeth with mesial/distal Class III cavities restored with CR with GFP (G4). The samples were submitted to the fracture strength test in a universal testing machine with a compression shear load applied at speed of 1.0 mm/min until fracture occurred. The data were submitted to one-way ANOVA (α=0.05) and the samples were analyzed for failure mode. The analysis did not show a significant statistical difference in fracture strength between the groups (p>0.05). The results showed that only endodontically treated teeth (G1) (753.4N) presented behavior similar to teeth with GFP (G2) (702.1N). The same occurred when comparing teeth with Class III cavities without GFP (G3) (670.2 N) and with GFP (G4) (746.1N). It can be concluded that glass fiber posts do not change the fracture strength of incisors with endodontic treatment and Class III cavities

Effect of carisolv and papacárie on the resin-dentin bond strength in sound and caries-affected primary molars

is study evaluated the influence of different chemomechanical caries removal techniques on the bond strength of an adhesive system to caries-affected and healthy dentin. Methods: Thirty healthy teeth were randomly divided into three groups: Group 1 (control): no caries removal technique was applied; Group 2: chemomechanical technique using Carisolv®; and Group 3: chemomechanical technique using Papacárie®. Twenty caries-affected teeth were divided into two groups: Group 4: chemomechanical technique using Carisolv; and Group 5: chemomechanical technique using Papacárie. The teeth received the application of an etch-andrinse adhesive system, were restored with composite resin, and then sectioned to obtain 4 hourglassshaped slabs from each specimen, which were subjected to a microtensile bond strength test. Data were analyzed statistically by ANOVA and Tukeys test (a=0.05). Results: G1 (13.387 ± 6.1074), G2 (18.123 ± 3.2611) and G3 (12.781 ± 4.5652) presented statistically significant higher mean bond strength values than the other groups (p0.05). G4 (6.228 ± 5.3435) and G5 (6.482 ± 3.2076) presented the lowest mean bond strength values and were statistically similar to each other (p>0.05). Conclusions: Neither of the chemomechanical caries removal methods interfered in the resin-dentin bond strength. However, lower tensile bond strength was found to caries-affected dentin

Bonding to wet or dry deproteinized dentin: microtensile bond strength and confocal laser micromorphology analysis

Aim: To investigate the influence of deproteinization and moisture condition (wet vs. dry) on the bond strength and micromorphology of resin-dentin bonding interfaces. Methods: Dentin surfaces were etched with 37% phosphoric acid for 15 s and rinsed with water. Four groups (n = 10) were tested: WET: dentin was left visibly moist; DRY: dentin was dried with compressed air; WET-D: dentin was deproteinized for 60 s using 10% NaOCl solution and left moist; DRY-D: dentin was deproteinized and dried. Prime&Bond 2.1 adhesive was applied and the teeth were restored with composite resin. Microtensile test was carried out after 24 h, and failure modes classified under magnification. Data were subjected to two-way ANOVA and Tukey’s test (P 0.05). Adhesive failures were predominant. Analysis of micromorphology showed formation of a collagen-resin hybrid layer only for the non-deproteinized groups. Adhesive penetration into the dentinal tubules was deeper for the DRY-D compared to the WETD group. Conclusion: The bond strength was not dependent on the moisture condition and a more homogeneous hybridization was obtained when dentin was deproteinized

Bonding to wet or dry deproteinized dentin: microtensile bond strength and confocal laser micromorphology analysis

investigate the influence of deproteinization and moisture condition (wet vs. dry) on the bond strength and micromorphology of resin-dentin bonding interfaces. Methods: Dentin surfaces were etched with 37% phosphoric acid for 15 s and rinsed with water. Four groups (n = 10) were tested: WET: dentin was left visibly moist; DRY: dentin was dried with compressed air; WET-D: dentin was deproteinized for 60 s using 10% NaOCl solution and left moist; DRY-D: dentin was deproteinized and dried. Prime&Bond 2.1 adhesive was applied and the teeth were restored with composite resin. Microtensile test was carried out after 24 h, and failure modes classified under magnification. Data were subjected to two-way ANOVA and Tukeys test (P 0.05). Adhesive failures were predominant. Analysis of micromorphology showed formation of a collagen-resin hybrid layer only for the non-deproteinized groups. Adhesive penetration into the dentinal tubules was deeper for the DRY-D compared to the WETD group. Conclusion: The bond strength was not dependent on the moisture condition and a more homogeneous hybridization was obtained when dentin was deproteinized

Task-based approach used on surfaces sampling strategy definition: the case of antineoplastic occupational exposure

Task-based approach implicates identifying all the tasks developed in each workplace aiming to refine the exposure characterization. The starting point of this approach is the recognition that only through a more detailed and comprehensive understanding of tasks is possible to understand, in more detail, the exposure scenario. In addition allows also the most suitable risk management measures identification. This approach can be also used when there is a need of identifying the workplace surfaces for sampling chemicals that have the dermal exposure route as the most important. In this case is possible to identify, through detail observation of tasks performance, the surfaces that involves higher contact (frequency) by the workers and can be contaminated. Identify the surfaces to sample when performing occupational exposure assessment to antineoplasic agents. Surfaces selection done based on the task-based approach

Influence of ferrule preparation with or without glass fiber post on fracture resistance of endodontically treated teeth

OBJECTIVE: This study evaluated the effect of ferrule preparation (Fp) on the fracture resistance of endodontically treated teeth, restored with composite resin cores with or without glass fiber posts. MATERIAL AND METHODS: Forty-four bovine teeth were sectioned 19 or 17 mm (2 mm ferrule) from the apex, endodontically treated and assigned to four groups (n = 11): Group 1: Fp and post; Group 2: Fp and without post; Group 3: without Fp and with post; Group 4: without Fp and without post. All specimens were restored with composite resin core and metal crown. Specimens were subjected to fracture resistance testing in a universal testing machine at a crosshead speed of 0.5 mm/min. The data were analyzed by two-way ANOVA and Tukey's tests (&#945;=0.05). RESULTS: The mean fracture resistance values were as follows: Group 1: 573.3 N; Group 2: 552.5 N; Group 3: 275.3 N; Group 4: 258.6 N. Significantly higher fracture resistance was found for the groups with Fp (p<0.001). CONCLUSION: There was no statistically significant interaction between the "Fp" and "post" factors (p = 0.954). The ferrule preparation increased the fracture resistance of endodontically treated teeth. However, the use of glass fiber post showed no significant influence on the fracture resistance

Evaluation of a quality improvement intervention to reduce anastomotic leak following right colectomy (EAGLE): pragmatic, batched stepped-wedge, cluster-randomized trial in 64 countries

Background Anastomotic leak affects 8 per cent of patients after right colectomy with a 10-fold increased risk of postoperative death. The EAGLE study aimed to develop and test whether an international, standardized quality improvement intervention could reduce anastomotic leaks. Methods The internationally intended protocol, iteratively co-developed by a multistage Delphi process, comprised an online educational module introducing risk stratification, an intraoperative checklist, and harmonized surgical techniques. Clusters (hospital teams) were randomized to one of three arms with varied sequences of intervention/data collection by a derived stepped-wedge batch design (at least 18 hospital teams per batch). Patients were blinded to the study allocation. Low- and middle-income country enrolment was encouraged. The primary outcome (assessed by intention to treat) was anastomotic leak rate, and subgroup analyses by module completion (at least 80 per cent of surgeons, high engagement; less than 50 per cent, low engagement) were preplanned. Results A total 355 hospital teams registered, with 332 from 64 countries (39.2 per cent low and middle income) included in the final analysis. The online modules were completed by half of the surgeons (2143 of 4411). The primary analysis included 3039 of the 3268 patients recruited (206 patients had no anastomosis and 23 were lost to follow-up), with anastomotic leaks arising before and after the intervention in 10.1 and 9.6 per cent respectively (adjusted OR 0.87, 95 per cent c.i. 0.59 to 1.30; P = 0.498). The proportion of surgeons completing the educational modules was an influence: the leak rate decreased from 12.2 per cent (61 of 500) before intervention to 5.1 per cent (24 of 473) after intervention in high-engagement centres (adjusted OR 0.36, 0.20 to 0.64; P &lt; 0.001), but this was not observed in low-engagement hospitals (8.3 per cent (59 of 714) and 13.8 per cent (61 of 443) respectively; adjusted OR 2.09, 1.31 to 3.31). Conclusion Completion of globally available digital training by engaged teams can alter anastomotic leak rates. Registration number: NCT04270721 (http://www.clinicaltrials.gov)