246 research outputs found
Dissolution influences on gypsum rock under short and long-term loading: Implications for dams
Dissolution of soluble substrates such as gypsum presents a major hazard to dams in many parts of the world. This research simulates hypothesised conditions beneath the Mosul Dam, northwest Iraq, where collapse of a karstic system associated with continuous fresh water supply from its reservoir is a recognised problem. Gypsum rocks from northern Iraq and similar rocks from Bantycock gypsum mine, UK, were analysed for short-term mechanical response following immersion (5 to 50 weeks) and long-term loading during immersion (maximum 50 weeks). New experimental devices were developed from a conventional oedometer. Cylinder samples provided a proxy for massive gypsum strata. Samples were permanently submerged at atmospheric water pressure, with groundwater recharge, flow and dissolution simulated by regular changes of water. Stress on each sample was progressively increased to a maximum of 2688 kPa. Small increases in strain were recorded by the end of each test but no failures occurred within 60 days. However, notable failure due to atmospheric water pressure and axial stress occurred over long time periods. Visible physical changes included a
decrease in sample mass and volume. Similar change was recorded in ultrasonic
velocities. These indicate that gypsum collapse risk beneath dams requires prolonged
exposure to dissolution. The modified device performed well and was robust, and demonstrates that such a modification can provide a simple low cost system for conducting laboratory creep tests on weak rocks
Influence of Sample Height-to-Width Ratios on Failure Mode for Rectangular Prism Samples of Hard Rock Loaded In Uniaxial Compression
Geohazards analysis of Pisa tunnel in a fractured incompetent rocks in Zagros Mountains, Iran.
The Pisa 2 tunnel with 740 m in length and 20° N trend is located along the Kazerun fault zone in Simply Folded Belt of Zagros, Iran. This tunnel has been excavated in the fractured incompetent marl layers with high expansive pressure of up to 2 kg/cm2. In this study, the geological hazards along the tunnel have been recognized and categorized. This study revealed that, in the long-term usage of the tunnel, the lining did not endure against the loading and the secondary leakages. It is mainly attributed due to the non-efficiencies of drainage and isolation systems in the tunnel site. Therefore, it caused asphalt damage, drainage damage, and wall distortion. FLAC3D software has been used in this research. We conducted various analyses for pre-excavation stress states, syn-excavation, and post-excavation strain states. The results showed no indication of instability and critical deformations during the excavation time. It also revealed that due to the non-efficiencies of drainage and isolation systems against secondary leakages and consequently marl expansion, the volumetric and shear strains (i.e., expansions and displacements) have exceeded from the critical states of strain along the tunnel. For various remedy purpose, this paper attempted several measures that can be taken in order to modify the drainage and isolation systems along the tunnel area. The reconstruction of drainage systems with suitable reinforced concrete and adequate slope has been proposed. The width of channel and isolation of backside of lining and implementation of multi-order outlets (i.e., backside of lining) for draining of groundwater into where the main drainage systems are located in the tunnel gallery were suggested
A Criterion for Brittle Failure of Rocks Using the Theory of Critical Distances
This paper presents a new analytical criterion for brittle failure of rocks and heavily overconsolidated soils. Griffith’s model of a randomly oriented defect under a biaxial stress state is used to keep the criterion simple. The Griffith’s criterion is improved because the maximum tensile strength is not evaluated at the boundary of the defect but at a certain distance from the boundary, known as the critical distance. This fracture
criterion is known as the Point Method, and is part of the Theory of Critical Distances, which is utilized in fracture mechanics. The proposed failure criterion has two parameters: the inherent tensile strength, ó0, and the ratio of the half-length of the initial crack/flaw to the critical distance, a/L. These parameters are difficult to measure but they may be correlated with the uniaxial compressive and tensile strengths, óc and ót.
The proposed criterion is able to reproduce the common range of strength ratios for rocks and heavily overconsolidated soils (óc/ót=3-50) and the influence of several microstructural rock properties, such as texture and porosity. Good agreement with laboratory tests reported in the literature is found for tensile and low confining stresses.The work presented was initiated during a research project on “Structural integrity
assessments of notch-type defects", for the Spanish Ministry of Science and Innovation
(Ref.: MAT2010-15721)
Rock Mass Quality Rating (RMQR) System and Its Application to the Estimation of Geomechanical Characteristics of Rock Masses
Influence of Fracture Systems and Weathering on the Sustainability of Rock Excavation Made for the Purpose of Infrastructure Construction
Rock mass assessment along the right bank of river Sutlej, Luhri, Himachal Pradesh, India
Rock quality designation (RQD): time to rest in peace
Rock quality designation (RQD) was introduced by Don Deere in the mid-1960s as a means of using diamond core to classify rock for engineering purposes. Subsequently, it was incorporated into the rock mass rating (RMR) and Q-system classification methods that, worldwide, now play substantial roles in rock mechanics design, whether for tunnels, foundations, rock slopes or rock excavation. It is shown that a key facet of the definition of RQD is ignored in many parts of the world, and it is noted that there are several inherent limitations to the use of RQD. Based on mapping of rock formations by 17 independent professionals at different locations in Australia and South Africa, it is shown that differences in assessed RQD values result in significant errors in computed RMR and Q ratings, and also in geological strength index (GSI) and mining rock mass rating (MRMR). The introduction of a look-up chart for assessing GSI has effectively removed the need to measure, or estimate, RQD. It has been found that GSI values derived from the look-up chart are as valid as those derived by calculation from the original component parameters, and are satisfactorily consistent between professionals from diverse backgrounds. The look-up charts provide a quick and appropriate means of assessing GSI from exposures. GSI is, in turn, a useful rock mass strength index; one new application is presented for assessing potential erosion of unlined spillways in rock. Incorporation of RQD within the RMR and Q classification systems was a matter of historical development, and its incorporation into rock mass classifications is no longer necessary
- …