3,049 research outputs found
Hydrodynamic air lubricated compliant surface bearing for an automotive gas turbine engine. 2: Materials and coatings
Material coatings for an air-lubricated, compliant journal bearing for an automotive gas turbine engine were exposed to service test temperatures of 540 C or 650 C for 300 hours, and to 10 temperature cycles from room temperatures to the service test temperatures. Selected coatings were then put on journal and partial-arc foils and tested in start-stop cycle tests at 14 kPa (2 psi) loading for 2000 cycles. Half of the test cycles were performed at a test chamber service temperature of 540 C (1000 F) or 650 C (1200 F); the other half were performed at room temperature. Based on test results, the following combinations and their service temperature limitations are recommended: HL-800 TM (CdO and graphite) on foil versus chrome carbide on journal up to 370 C (700 F); NASA PS 120 (Tribaloy 400, silver and CaF2 on journal versus uncoated foil up to 540 C (1000 F); and Kaman DES on journal and foil up to 640 C (1200 F). Kaman DES coating system was further tested successfully at 35 kPa (5 psi) loading for 2000 start-stop cycles
Friction and morphology of magnetic tapes in sliding contact with nickel-zinc ferrite
Friction and morphological studies were conducted with magnetic tapes containing a Ni-Zn ferrite hemispherical pin in laboratory air at a relative humidity of 40 percent and at 23 C. The results indicate that the binder plays a significant role in the friction properties, morphology, and microstructure of the tape. Comparisons were made with four binders: nitrocellulose; poly (vinyledene) chloride; cellulose acetate; and hydroxyl-terminated, low molecular weight polyester added to the base polymer, polyester-polyurethane. The coefficient of friction was lowest for the tape with the nitrocellulose binder and increased in the order hydroxylterminated, low molecular weight polyester resin; poly (vinyledene) chloride; and cellulose acetate. The degree of enclosure of the oxide particles by the binder was highest for hydroxyl-terminated, low molecular weight polyester and decreased in the order cellulose acetate, poly (vinyledene) chloride, and nitrocellulose. The nature of deformation of the tape was a factor in controlling friction. The coefficient of friction under elastic contact conditions was considerably lower than under conditions that produced plastic contacts
High temperature self-lubricating coatings for air lubricated foil bearings for the automotive gas turbine engine
coating combinations were developed for compliant surface bearings and journals to be used in an automotive gas turbine engine. The coatings were able to withstand the sliding start/stops during rotor liftoff and touchdown and occasional short time, high speed rubs under representative loading of the engine. Some dozen coating variations of CdO-graphite, Cr2O3 (by sputtering) and CaF2 (plasma sprayed) were identified. The coatings were optimized and they were examined for stoichiometry, metallurgical condition, and adhesion. Sputtered Cr2O3 was most adherent when optimum parameters were used and it was applied on an annealed (soft) substrate. Metallic binders and interlayers were used to improve the ductility and the adherence
A Survey of Morphing Techniques
Image morphing provides the tool to generate the flexible and powerful visual effect. Morphing depicts the transformation of one image into another image. The process of image morphing starts with the feature specification phase and then proceeds to warp generation phase, followed by the transition control phase. This paper surveys the various techniques available for all three stages of image morphing
Bending and wrinkling as competing relaxation pathways for strained free-hanging films
An equilibrium phase diagram for the shape of compressively strained
free-hanging films is developed by total strain energy minimization. For small
strain gradients {\Delta}{\epsilon}, the film wrinkles, while for sufficiently
large {\Delta}{\epsilon}, a phase transition from wrinkling to bending occurs.
We consider competing relaxation mechanisms for free-hanging films, which have
rolled up into tube structures, and we provide an upper limit for the maximum
achievable number of tube rotations.Comment: 4 pages, 4 figure
Dynamics of Phononic Dissipation at the Atomic Scale: Dependence on Internal Degrees of Freedom
Dynamics of dissipation of a local phonon distribution to the substrate is a
key issue in friction between sliding surfaces as well as in boundary
lubrication. We consider a model system consisting of an excited nano-particle
which is weakly coupled with a substrate. Using three different methods we
solve the dynamics of energy dissipation for different types of coupling
between the nano-particle and the substrate, where different types of
dimensionality and phonon densities of states were also considered for the
substrate. In this paper, we present our analysis of transient properties of
energy dissipation via phonon discharge in the microscopic level towards the
substrate. Our theoretical analysis can be extended to treat realistic
lubricant molecules or asperities, and also substrates with more complex
densities of states. We found that the decay rate of the nano-particle phonons
increases as the square of the interaction constant in the harmonic
approximation.Comment: 10 pages, 6 figures, submitted to Phys. Rev.
Interval timing in children:effects of auditory and visual pacing stimuli and relationships with reading and attention variables
Motor timing tasks have been employed in studies of neurodevelopmental disorders such as developmental dyslexia and ADHD, where they provide an index of temporal processing ability. Investigations of these disorders have used different stimulus parameters within the motor timing tasks which are likely to affect performance measures. Here we assessed the effect of auditory and visual pacing stimuli on synchronised motor timing performance and its relationship with cognitive and behavioural predictors that are commonly used in the diagnosis of these highly prevalent developmental disorders. Twenty- one children (mean age 9.6 years) completed a finger tapping task in two stimulus conditions, together with additional psychometric measures. As anticipated, synchronisation to the beat (ISI 329 ms) was less accurate in the visually paced condition. Decomposition of timing variance indicated that this effect resulted from differences in the way that visual and auditory paced tasks are processed by central timekeeping and associated peripheral implementation systems. The ability to utilise an efficient processing strategy on the visual task correlated with both reading and sustained attention skills. Dissociations between these patterns of relationship across task modality suggest that not all timing tasks are equivalent
SOLUBILITY AND DISSOLUTION ENHANCEMENT OF PIOGLITAZONE USING SOLID DISPERSION TECHNIQUE
Objective: To design the study to improve the solubility and hence enhance the dissolution of hydrophobic drug Pioglitazone in order to increase its bioavailability.Methods: Solid dispersion of Pioglitazone using carriers Poloxomer 188 and HPβCD was formulated in different ratios by microwave induced fusion method. In particular, the Microwave technology has been considered in order to prepare an enhanced release dosage form for poorly water soluble drug Pioglitazone. Statistical Analysis: Their physicochemical characteristics and solubility were compared to the corresponding dispersions and marketed drug. Drug and polymer were further characterized by FTIR.Results: The results of FTIR revealed that no chemical interaction between the drug and the polymer exist.Conclusion: All the formulations showed a marked increase in drug release with the increase in the concentration of Poloxomer 188 and HPβCD.Â
FORMULATION DEVELOPMENT AND EVALUATION OF ELEMENTARY OSMOTIC TABLET OF LISINOPRIL DIHYDRATE
Objective: Lisinopril Dihydrate is one of the antihypertensive drug used to control the high blood pressure. Osmotically Controlled release tablet of Lisinopril Dihydrate was performed for reducing dosing frequency and patient compliance.Methods: Elementary osmotic tablets of Lisinopril Dihydrate were developed using Sodium chloride as a key ingredient which gives osmogent property which provides driving force inside the core tablet and which leads to release of the drug. Microcrystalline cellulose used as a release retardant material in the present work. Different formulations were prepared by varying the concentrations using 32 factorial designs. It was applied to see the effect of variables Sodium chloride (X1) and MCC (X2) on the response percentage drug release as a dependent variable. These formulations were evaluated for, Hardness, Flow property, Thickness, Friability, Drug content and In vitro drug release. Tablets were coated with a semipermeable membrane using 5% w/v cellulose acetate(CA) in acetone and PEG 400(1%) used as Plasticizer. Coated Elementary osmotic tablets were drilled for delivery orifice using a standard micro drill of diameter size 0.8 mm.Results: Drug release rate was increased as the increase in the concentration of sodium chloride and release rate decreased on increasing the concentration of MCC. Drug release rate was directly proportional to delivery orifice size. SEM Study carried out for detection of diameter size of the delivery orifice. The FTIR studies demonstrate that there was no interaction between polymer and drug.Conclusion: The optimized formulation was stable for 3 mo of accelerated stability stud
- …