22 research outputs found
Applications and limitations of electron correlation microscopy to study relaxation dynamics in supercooled liquids
Electron correlation microscopy (ECM) is a way to measure structural relaxation times, Ď„, of liquids with nanometer-scale spatial resolution using coherent electron scattering equivalent of photon correlation spectroscopy. We have applied ECM with a 3.5 nm diameter probe to Pt57.5Cu14.7Ni5.3P22.5 amorphous nanorods and Pd40Ni40P20 bulk metallic glass (BMG) heated inside the STEM into the supercooled liquid region. These data demonstrate that the ECM technique is limited by the characteristics of the time series, which must be at least 40Ď„ to obtain a well-converged correlation function g2(t), and the time per frame, which must be less than 0.1Ď„ to obtain sufficient sampling. A high-speed direct electron camera enables fast acquisition and affords reliable g2(t) data even with low signal per frame
Ideal maximum strengths and defect-induced softening in nanocrystalline-nanotwinned metals
Strengthening of metals through nanoscale grain boundaries and coherent twin boundaries is manifested by a maximum strength—a phenomenon known as Hall–Petch breakdown. Different softening mechanisms are considered to occur for nanocrystalline and nanotwinned materials. Here, we report nanocrystalline-nanotwinned Ag materials that exhibit two strength transitions dissimilar from the above mechanisms. Atomistic simulations show three distinct strength regions as twin spacing decreases, delineated by positive Hall–Petch strengthening to grain-boundary-dictated (near-zero Hall–Petch slope) mechanisms and to softening (negative Hall–Petch slope) induced by twin-boundary defects. An ideal maximum strength is reached for a range of twin spacings below 7 nm. We synthesized nanocrystalline-nanotwinned Ag with hardness 3.05 GPa—42% higher than the current record, by segregating trace concentrations of Cu impurity (\u3c1.0 weight (wt)%). The microalloy retains excellent electrical conductivity and remains stable up to 653 K; 215 K better than for pure nanotwinned Ag. This breaks the existing trade-off between strength and electrical conductivity, and demonstrates the potential for creating interface-dominated materials with unprecedented mechanical and physical properties
Bulk single crystal growth and sample surface preparation of catalytic NaAu2
Here in we have grown bulk single crystals of NaAu2 for the first time to enable surface studies on the nature of the (111) bulk surface. This intermetallic compound exhibits surprisingly high catalytic activity for CO oxidation, a benchmark reaction. Theory predicts NaAu2 to be the most thermodynamically stable composition in the Na-Au binary phase diagram and NaAu2 has been seen to preferentially form in experiments containing Na and Au which supports this prediction. The (111) surface was also predicted to be the most stable and is nearly bulk-terminated making single crystal samples prepared with this crystallographic orientation a fitting choice. The crystal quality and surface composition of the metallographically prepared surface was determined by x-ray diffraction methods in addition to optical and electron microscopy
A Comparison of Shiga-Toxin 2 Bacteriophage from Classical Enterohemorrhagic Escherichia coli Serotypes and the German E. coli O104:H4 Outbreak Strain
Escherichia coli O104:H4 was associated with a severe foodborne disease outbreak originating in Germany in May 2011. More than 4000 illnesses and 50 deaths were reported. The outbreak strain was a typical enteroaggregative E. coli (EAEC) that acquired an antibiotic resistance plasmid and a Shiga-toxin 2 (Stx2)-encoding bacteriophage. Based on whole-genome phylogenies, the O104:H4 strain was most closely related to other EAEC strains; however, Stx2-bacteriophage are mobile, and do not necessarily share an evolutionary history with their bacterial host. In this study, we analyzed Stx2-bacteriophage from the E. coli O104:H4 outbreak isolates and compared them to all available Stx2-bacteriophage sequences. We also compared Stx2 production by an E. coli O104:H4 outbreak-associated isolate (ON-2011) to that of E. coli O157:H7 strains EDL933 and Sakai. Among the E. coli Stx2-phage sequences studied, that from O111:H- strain JB1-95 was most closely related phylogenetically to the Stx2-phage from the O104:H4 outbreak isolates. The phylogeny of most other Stx2-phage was largely concordant with their bacterial host genomes. Finally, O104:H4 strain ON-2011 produced less Stx2 than E. coli O157:H7 strains EDL933 and Sakai in culture; however, when mitomycin C was added, ON-2011 produced significantly more toxin than the E. coli O157:H7 strains. The Stx2-phage from the E. coli O104:H4 outbreak strain and the Stx2-phage from O111:H- strain JB1-95 likely share a common ancestor. Incongruence between the phylogenies of the Stx2-phage and their host genomes suggest the recent Stx2-phage acquisition by E. coli O104:H4. The increase in Stx2-production by ON-2011 following mitomycin C treatment may or may not be related to the high rates of hemolytic uremic syndrome associated with the German outbreak strain. Further studies are required to determine whether the elevated Stx2-production levels are due to bacteriophage or E. coli O104:H4 host related factors
Genome sequencing analysis identifies new loci associated with Lewy body dementia and provides insights into its genetic architecture
The genetic basis of Lewy body dementia (LBD) is not well understood. Here, we performed whole-genome sequencing in large cohorts of LBD cases and neurologically healthy controls to study the genetic architecture of this understudied form of dementia, and to generate a resource for the scientific community. Genome-wide association analysis identified five independent risk loci, whereas genome-wide gene-aggregation tests implicated mutations in the gene GBA. Genetic risk scores demonstrate that LBD shares risk profiles and pathways with Alzheimer's disease and Parkinson's disease, providing a deeper molecular understanding of the complex genetic architecture of this age-related neurodegenerative condition
Recommended from our members
Proceedings of the 13th annual conference of INEBRIA
CITATION: Watson, R., et al. 2016. Proceedings of the 13th annual conference of INEBRIA. Addiction Science & Clinical Practice, 11:13, doi:10.1186/s13722-016-0062-9.The original publication is available at https://ascpjournal.biomedcentral.comENGLISH SUMMARY : Meeting abstracts.https://ascpjournal.biomedcentral.com/articles/10.1186/s13722-016-0062-9Publisher's versio
Recommended from our members
Abrasion Resistant Coating and Method of making the same
An abrasion resistant coating is created by adding a ductile phase to a brittle matrix phase during spray coating where an Al-Cu-Fe quasicrystalline phase (brittle matrix) and an FeAl intermetallic (ductile phase) are combined. This composite coating produces a coating mostly of quasicrystal phase and an inter-splat layer of the FeAl phase to help reduce porosity and cracking within the coating. Coatings are prepared by plasma spraying unblended and blended quasicrystal and intermetallic powders. The blended powders contain 1, 5, 10 and 20 volume percent of the intermetallic powders. The unblended powders are either 100 volume percent quasicrystalline or 100 volume percent intermetallic; these unblended powders were studied for comparison to the others. Sufficient ductile phase should be added to the brittle matrix to transform abrasive wear mode from brittle fracture to plastic deformation, while at the same time the hardness of the composite should not be reduced below that of the original brittle phase material
Dynamic Nuclear Polarization of Metal-Doped Oxide Glasses: A Test of the Generality of Paramagnetic Metal Polarizing Agents
Nuclear magnetic resonance (NMR) spectroscopy can provide unique, atomic-level insights into the structure and dynamics of materials, but its applications are impeded by the intrinsically low sensitivity. Dynamic nuclear polarization (DNP) is poised to overcome this limitation, and indeed has revolutionized the study of surfaces; however, the current approaches are ill-suited for bulk solids. One potential pathway toward the hyperpolarization of bulk solids by DNP is through the inclusion of paramagnetic metal ions that can serve as polarizing agents. In this work, we compared the relative performance of two such dopants, Mn2+ and Gd3+, in three series of oxide glasses having chemical environments representative of those found in other crystalline and amorphous solids. In our studies, Gd3+ outperformed Mn2+, consistently providing more than one order of magnitude greater time savings. We attributed this difference mainly to the lack of hyperfine interaction to 55Mn