37 research outputs found
Coupled experiment/simulation approach for the design of radiation-hardened rare-earth doped optical fibers and amplifiers
We developed an approach to design radiation-hardened rare earth -doped fibers and amplifiers. This methodology combines testing experiments on these devices with particle swarm optimization (PSO) calculations. The composition of Er/Yb-doped phosphosilicate fibers was improved by introducing Cerium inside their cores. Such composition strongly reduces the amplifier radiation sensitivity, limiting its degradation: we observed a gain decreasing from 19 dB to 18 dB after 50 krad whereas previous studies reported higher degradations up to 0°dB at such doses. PSO calculations, taking only into account the radiation effects on the absorption efficiency around the pump and emission wavelengths, correctly reproduce the general trends of experimental results. This calculation tool has been used to study the influence of the amplifier design on its radiation response. The fiber length used to ensure the optimal amplification before irradiation may be rather defined and adjusted to optimize the amplifier performance over the whole space mission profile rather than before integration in the harsh environments. Both forward and backward pumping schemes lead to the same kind of degradation with our active fibers. By using this promising coupled approach, radiation-hardened amplifiers nearly insensitive to radiations may be designed in the future
Design of Radiation-Hardened Rare-Earth Doped Amplifiers Through a Coupled Experiment/Simulation Approach
We present an approach coupling a limited experimental number of tests with numerical simulations regarding the design of radiation-hardened (RH) rare earth (RE)-doped fiber amplifiers. Radiation tests are done on RE-doped fiber samples in order to measure and assess the values of the principal input parameters requested by the simulation tool based on particle swarm optimization (PSO) approach. The proposed simulation procedure is validated by comparing the calculation results with the measured degradations of two amplifiers made with standard and RH RE-doped optical fibers, respectively. After validation, the numerical code is used to theoretically investigate the influence of some amplifier design parameters on its sensitivity to radiations. Simulations show that the RE-doped fiber length used in the amplifier needs to be adjusted to optimize the amplifier performance over the whole space mission profile rather than to obtain the maximal amplification efficiency before its integration in the harsh environment. By combining this coupled approach with the newly-developed RH RE-doped fibers, fiber-based amplifiers nearly insensitive to space environment may be designed in the future
Recent advances in radiation-hardened fiber-based technologies for space applications
International audience; In this topical review, the recent progress on radiation-hardened fiber-based technologies is detailed, focusing on examples for space applications. In the first part of the review, we introduce the operational principles of the various fiber-based technologies considered for use in radiation environments: passive optical fibers for data links, diagnostics, active optical fibers for amplifiers and laser sources as well as the different classes of point and distributed fiber sensors: gyroscopes, Bragg gratings, Rayleigh, Raman or Brillouin-based distributed sensors. Second, we describe the state of the art regarding our knowledge of radiation effects on the performance of these devices, from the microscopic effects observed in the amorphous silica glass used to design fiber cores and cladding, to the macroscopic response of fiber-based devices and systems. Third, we present the recent advances regarding the hardening (improvement of the radiation tolerance) of these technologies acting on the material, device or system levels. From the review, the potential of fiber-based technologies for operation in radiation environments is demonstrated and the future challenges to be overcome in the coming years are presented
Comments about birefringence dispersion, with group and phase birefringence measurements in polarization-maintaining fibers
A recent JEOS-RP publication proposed Comments about Dispersion of Light Waves, and we present here complementary comments for birefringence dispersion in polarization-maintaining (PM) fibers, and for its measurement techniques based on channeled spectrum analysis. We start by a study of early seminal papers, and we propose additional explanations to get a simpler understanding of the subject. A geometrical construction is described to relate phase birefringence to group birefringence, and it is applied to the measurement of several kinds of PM fibers using stress-induced photo-elasticity, or shape birefringence. These measurements confirm clearly that the difference between group birefringence and phase birefringence is limited to 15–20% in stress-induced PM fibers (bow-tie, panda, or tiger-eye), but that it can get up to a 3-fold factor with an elliptical-core (E-core) fiber. There are also surprising results with solid-core micro-structured PM fibers, that are based on shape birefringence, as E-core fibers
6 MeV Electron exposure effects on OFDR-based distributed fiber sensors
The impact of exposing an optical fiber to 6-MeV electrons on the performances of optical frequency domain reflectometry (OFDR) distributed sensors is investigated. Six different types of optical fibers with different core compositions and coatings have been tested: four fibers are metal coated (copper, gold, or aluminum) for high-temperature >300 °C) operations while the two others have telecom-grade acrylate coatings for operation below 80 °C. The fiber Rayleigh signature used to perform the OFDR sensing remains almost unaffected after an electron exposure. Indeed, the measured radiation-induced temperature errors are lower than about 3 °C, close to the setup uncertainties, when the OFDR operates as a temperature sensor
Realite du syndrome piriforme
BORDEAUX2-BU Santé (330632101) / SudocPARIS-BIUM (751062103) / SudocSudocFranceF
Radiation-resistant rare-earth-doped optical fiber and method of radiation-hardening a rare-earth-doped optical fiber
Post-treatment of DBR fibre lasers for enhanced beat-frequency in dual-polarization operation
International audienceUV photo-ablation provides an efficient and reproducible means to control the birefringence of a dual-frequency DBR fiber laser. The resulting beat note can be finely tuned by real-time measurement during the process from typically 100 MHz to about 6 GHz, independently of the active medium length
55 W actively q-switched single oscillator Tm3+, Ho3+-codoped silica polarization maintaining 2.09 µm fiber laser
A 793 nm diode-pumped actively Q-switched Tm3+, Ho3+-codoped PM 2.09 ?m fiber laser emitting 55 W of average power with 100 ns pulse width and 200 kHz repetition rate is reported. End-caps spliced on fiber tips enable laser power scaling with good power stability and beam quality factors (M2 < 1.7)