Multi-axial response of idealized cermets

The yield response of two idealized cermets comprising mono and bi-disperse steel spheres in a Sn/Pb solder matrix has been investigated for a range of axisymmetric stress states. Proportional stress path experiments are reported, from which are extracted the initial yield surfaces and their evolution with increasing plastic strain. The initial yield strength is nearly independent of the hydrostatic pressure but the strain hardening rate increases with stress triaxiality up to a critical value. For higher triaxialities, the responses are independent of hydrostatic pressure. Multi-axial measurements along with X-ray tomography were used to demonstrate that the deformation of these idealized cermets occurs by two competing mechanisms: (i) a granular flow mechanism that operates at low levels of triaxiality, where volumetric dilation occurs under compressive stress states, and (ii) a plastically incompressible mechanism that operates at high stress triaxialities. A phenomenological viscoplastic constitutive model that incorporates both deformation mechanisms is presented. While such multi-axial measurements are difficult for commercial cermets with yield strengths on the order of a few GPa, the form of their constitutive relation is expected to be similar to that of the idealized cermets presented here

Characterization and structural properties of bamboo fibre solid foams

In this work, cellulose fibres extracted from bamboo culms were used to fabricate two types of cellular materials: rigid foams and fibrous networks. A relatively simple and low-technology fabrication method is presented, using natural binders and blowing agents to manufacture rigid foams, and fibrillation by partial hydrolysis in H2SO4 to manufacture fibrous networks. The compressive response is related to the internal microstructure and processing parameters. In the case of fibrous networks, the achievable relative density range is determined by the length of initial fibres and extent of external fibrillation. The compressive properties are dictated both by the density of the network and strength of the fibrous bridges, showing a linear stiffness-density relationship due to the length of fibres, and an inverse relationship at increased external fibrillation. The rigid foams showed an orthotropic internal microstructure but nearly isotropic compressive response, due to the influence of the interpenetrating void structure on the deformation and fracture mechanisms. The results show the potential of bamboo-fibre porous materials as low cost, lightweight structural materials

Functional crosstalk in culture between macrophages and trigeminal sensory neurons of a mouse genetic model of migraine

Background: Enhanced activity of trigeminal ganglion neurons is thought to underlie neuronal sensitization facilitating the onset of chronic pain attacks, including migraine. Recurrent headache attacks might establish a chronic neuroinflammatory ganglion profile contributing to the hypersensitive phenotype. Since it is difficult to study this process in vivo, we investigated functional crosstalk between macrophages and sensory neurons in primary cultures from trigeminal sensory ganglia of wild-type (WT) or knock-in (KI) mice expressing the Cacna1a gene mutation (R192Q) found in familial hemiplegic migraine-type 1. After studying the number and morphology of resident macrophages in culture, the consequences of adding host macrophages on macrophage phagocytosis and membrane currents mediated by pain-transducing P2X3 receptors on sensory neurons were examined.Results: KI ganglion cultures constitutively contained a larger number of active macrophages, although no difference in P2X3 receptor expression was found. Co-culturing WT or KI ganglia with host macrophages (active as much as resident cells) strongly stimulated single cell phagocytosis. The same protocol had no effect on P2X3 receptor expression in WT or KI co-cultures, but it largely enhanced WT neuron currents that grew to the high amplitude constitutively seen for KI neurons. No further potentiation of KI neuronal currents was observed.Conclusions: Trigeminal ganglion cultures from a genetic mouse model of migraine showed basal macrophage activation together with enhanced neuronal currents mediated by P2X3 receptors. This phenotype could be replicated in WT cultures by adding host macrophages, indicating an important functional crosstalk between macrophages and sensory neurons. \ua9 2012 Franceschini et al.; licensee BioMed Central Ltd

Deformation mechanisms of idealised cermets under multi-axial loading

The response of idealised cermets comprising approximately 60% by volume steel spheres in a Sn/Pb solder matrix is investigated under a range of axisymmetric compressive stress states. Digital volume correlation (DVC) analysis of X-ray micro-computed tomography scans (μ-CT), and the measured macroscopic stress-strain curves of the specimens revealed two deformation mechanisms. At low triaxialities the deformation is granular in nature, with dilation occurring within shear bands. Under higher imposed hydrostatic pressures, the deformation mechanism transitions to a more homogeneous incompressible mode. However, DVC analyses revealed that under all triaxialities there are regions with local dilatory and compaction responses, with the magnitude of dilation and the number of zones wherein dilation occurs decreasing with increasing triaxiality. Two numerical models are presented in order to clarify these mechanisms: (i) a periodic unit cell model comprising nearly rigid spherical particles in a porous metal matrix and (ii) a discrete element model comprising a large random aggregate of spheres connected by non-linear normal and tangential “springs”. The periodic unit cell model captured the measured stress-strain response with reasonable accuracy but under-predicted the observed dilation at the lower triaxialities, because the kinematic constraints imposed by the skeleton of rigid particles were not accurately accounted for in this model. By contrast, the discrete element model captured the kinematics and predicted both the overall levels of dilation and the simultaneous presence of both local compaction and dilatory regions with the specimens. However, the levels of dilation in this model are dependent on the assumed contact law between the spheres. Moreover, since the matrix is not explicitly included in the analysis, this model cannot be used to predict the stress-strain responses. These analyses have revealed that the complete constitutive response of cermets depends both on the kinematic constraints imposed by the particle aggregate skeleton, and the constraints imposed by the metal matrix filling the interstitial spaces in that skeleton.The authors are grateful to the Office of Naval Research (ONR) for their financial support through grant number N00014121063

The Virtual Nose: Assessment of Static Nasal Airway Obstruction Using Computational Simulations and 3D-Printed Models

BACKGROUND: The use of virtual noses to predict the outcome of surgery is of increasing interests, particularly, as detailed and objective pre- and postoperative assessments of nasal airway obstruction (NAO) are difficult to perform. The objective of this article is to validate predictions using virtual noses against their experimentally measured counterpart in rigid 3D-printed models. METHODS: Virtual nose models, with and without NAO, were reconstructed from patients' cone beam computed tomography scans, and used to evaluate airflow characteristics through computational fluid dynamics simulations. Prototypes of the reconstructed models were 3D printed and instrumented experimentally for pressure measurements. RESULTS: Correlation between the numerical predictions and experimental measurements was shown. Analysis of the flow field indicated that the NAO in the nasal valve increases significantly the wall pressure, shear stress, and incremental nasal resistance behind the obstruction. CONCLUSIONS: Airflow predictions in static virtual noses correlate well with detailed experimental measurements on 3D-printed replicas of patient airways

Robust Adaptive Control of the Mold Level in the Continuous Casting Process Using Multiple Models

Abstract-In the continuous casting of steel, mold level control is fundamental for obtaining high productivity and high quality. Using conventional methods, it is difficult to achieve both stability and performance robustness because of different classes of disturbances and parameters uncertainties in the process. This paper presents a multi-model adaptive control architecture based on the so-called RMMAC methodology. With the help of precise definition of robust performance requirements, the number of models, estimators and controllers are merely derived. More importantly, the combination of robust non-adaptive mixed-µ synthesis and stochastic hypothesis testing concepts enables controller performances prediction as well as online monitoring process parameters which could be used by operators to take corrective actions. The generated signals are likewise useful for understanding the physical phenomena in the process

Lambda production in central Pb+Pb collisions at CERN-SPS energies

In this paper we present recent results from the NA49 experiment for $\Lambda$ and $\bar{\Lambda}$ hyperons produced in central Pb+Pb collisions at 40, 80 and 158 A$\cdot$GeV. Transverse mass spectra and rapidity distributions for $\Lambda$ are shown for all three energies. The shape of the rapidity distribution becomes flatter with increasing beam energy. The multiplicities at mid-rapidity as well as the total yields are studied as a function of collision energy including AGS measurements. The ratio $\Lambda/\pi$ at mid-rapidity and in 4$\pi$ has a maximum around 40 A$\cdot$GeV. In addition, $\bar{\Lambda}$ rapidity distributions have been measured at 40 and 80 A$\cdot$GeV, which allows to study the $\bar{\Lambda}$/$\Lambda$ ratio.Comment: SQM proceedings. J. Phys. G: Nucl. Part. Phys.: submitte

Peer assessing individual contributions in a group project

Graduates are expected to have good academic knowledge but also the professional skills required in the workplace. One such ‘soft’ skill is the ability to give constructive criticism and provide meaningful but professional feedback. This is particularly relevant when working in a team within industry, where peers need to influence each other to improve their project outcomes and chances of success. The development of student’s skills to generate such feedback should be supported within higher education. Specifically the IPAC Consortium investigates the use of Individual Peer Assessed Contribution to group work. In this context, students create an output directed to their own peers (i.e. a form of external-facing assessment), and prepares students for similar practices in industry. This paper, linked to the roundtable session on external-facing assessments proposed by Grindle and Tong, investigates staff and student perceptions on such practice. Insights gained to this date are presented