10,295 research outputs found
Well-posedness of a model for structural acoustic coupling in a cavity enclosed by a thin cylindrical shell
A fully coupled mathematical model describing the interactions between a vibrating thin cylindrical shell and enclosed acoustic field is presented. Because the model will ultimately be used in control applications involving piezoceramic actuators, the loads and material contributions resulting from piezoceramic patches bonded to the shell are included in the discussion. Theoretical and computational issues lead to the consideration of a weak form of the modeling set of partial differential equations (PDE's) and through the use of a semigroup formulation, well-posedness results for the system model are obtained
The modeling of piezoceramic patch interactions with shells, plates and beams
General models describing the interactions between a pair of piezoceramic patches and elastic substructures consisting of a cylindrical shell, plate and beam are presented. In each case, the manner in which the patch loads enter both the strong and weak forms of the time-dependent structural equations of motion is described. Through force and moment balancing, these loads are then determined in terms of material properties of the patch and substructure (thickness, elastic properties, Poisson ratios), the geometry of the patch placement, and the voltages into the patches. In the case of the shell, the coupling between banding and inplane deformations, which is due to the curvature, is retained. These models are sufficiently general to allow for potentially different patch voltages which implies that they can be suitably employed when using piezoceramic patches for controlling system dynamics when both extensional and bending vibrations are present
A comparison of time domain boundary conditions for acoustic waves in wave guides
Researchers consider several types of boundary conditions in the context of time domain models for acoustic waves. Experiments with four different duct terminations (hard wall, free radiation, foam, and wedge) were carried out in a wave duct from which reflection coefficients over a wide frequency range were measured. These reflection coefficients were used to estimate parameters in the time domain boundary conditions. A comparison of the relative merits of the models in describing the data is presented. Boundary conditions which yield a good fit of the model to the experimental data were found for all duct terminations except the wedge
Model validation for a noninvasive arterial stenosis detection problem
Copyright @ 2013 American Institute of Mathematical SciencesA current thrust in medical research is the development of a non-invasive method for detection, localization, and characterization of an arterial stenosis (a blockage or partial blockage in an artery). A method has been proposed to detect shear waves in the chest cavity which have been generated by disturbances in the blood flow resulting from a stenosis. In order to develop this methodology further, we use both one-dimensional pressure and shear wave experimental data from novel acoustic phantoms to validate corresponding viscoelastic mathematical models, which were developed in a concept paper [8] and refined herein. We estimate model parameters which give a good fit (in a sense to be precisely defined) to the experimental data, and use asymptotic error theory to provide confidence intervals for parameter estimates. Finally, since a robust error model is necessary for accurate parameter estimates and confidence analysis, we include a comparison of absolute and relative models for measurement error.The National Institute of Allergy and Infectious Diseases, the Air Force Office of Scientific Research, the Deopartment of Education and the Engineering and Physical Sciences Research Council (EPSRC)
Recommended from our members
Effects of drop and film viscosity on drop impacts onto thin films
While drop-film impacts have been studied extensively in the past, little thought has been given towards separating the effects of the drop fluid properties from those of the film. Distinguishing between the behaviors resulting from characteristics of each independently could provide insight into the underlying physical phenomena with a clarity that is unavailable when the drop and the film consist of identical liquids. In this study, the viscosity is the central parameter varied in both drop and film liquid. Using water, aqueous glycerol mixtures, and Fluoroinert FC-72, a range of kinematic viscosity covering 3 orders of magnitude (4 × 10-7 - 6.5 × 10 -4 m2/s) is examined; a smaller range of surface tension (0.024-0.072 N/m) is covered, as well. Drop impacts occur over a range of Weber numbers from 20 to 3000 and Reynolds numbers from 20 to 14000. Impact outcomes categorized are both formation of a crown and splashing from the crown. Criteria for each impact outcome are presented in light of both film and drop properties; certain outcomes are found to depend more strongly on either the properties of the drop or the film individually. Crown formation appears to relate more strongly to the film's properties, whereas crown splashing has some dependence on the drop properties. Existing splashing correlations are examined in light of the separation of properties. © 2013 by Begell House, Inc
Dynamic characteristics and processing of fillers in polyurethane elastomers for vibration damping applications
Polyurethane elastomers have the potential of being used to reduce vibrational noise in many engineering applications. The performance of the elastomer is directly related to matching the nature of the mechanical loss characteristics to the frequency and temperature dependence of the source of the vibration. Materials with a broad frequency response and good mechanical properties are desirable for situations were load bearing and isolation becomes an issue. Because automobile, and other related vehicles operate over a broad temperature range, it is desirable for the damping characteristics of the elastomer to ideally be independent of temperature and frequency. In practice, this is not possible and the creation of materials with a broad spectrum response is desirable. In this paper, the effects of various fillers on the breadth and temperature dependence of the vibration damping characteristics of a filled and crosslinked polyurethane elastomer are explored. The fillers studied are wollastonite, barium sulphate and talc. These materials have different shapes, sizes and surface chemistry and undergo different types of interaction with the matrix. The vibration damping characteristics were further varied by the use of a crosslinking agent. Data presented on the rheological characteristics indicate the strength of the filler-polyol interactions. Dielectric relaxation and dynamic mechanical thermal analysis demonstrate the way in which changes in the type of filler, concentration and amount of crosslinker lead to changes in the location and breadth of the energy dissipation process in these elastomers. The vibration damping characteristics of a selected material are presented to demonstrate the potential of these materials
Ground-source heat pumps and underground thermal energy storage: energy for the future
We need energy for space heating—but in most cases not where or when energy sources are available. Energy storage, which helps match energy supply and demand, has been practised for centuries, also in Norway. Energy storage systems will increase the potential of utilising renewable
energy sources such as geothermal energy, solar heat and waste heat. The most frequently-used storage technology for heat and ‘coolth’ is Underground Thermal Energy Storage (UTES). The ground has proved to be an ideal medium for storing heat and cold in large quantities and over several seasons or years. UTES systems in the Nordic countries are mostly used in combination with Ground-Source Heat Pumps (GSHP). Several different UTES systems have been developed
and tested. Two types of system, Aquifer (ATES) and borehole (BTES) storage, have had a general commercial breakthrough in the last decades in the Nordic countries. Today, about 15,000 GSHP systems exist in Norway extracting about 1.5 TWh heat from the ground. About 280 of the Norwegian GSHP installations are medium- to large-scale systems (> 50 kW) for commercial/public buildings and for multi-family dwellings. The two largest closed-loop GSHP systems in Europe, using boreholes as ground heat exchangers, are located in Norway
Approximation methods for control of acoustic/structure models with piezoceramic actuators
The active control of acoustic pressure in a 2-D cavity with a flexible boundary (a beam) is considered. Specifically, this control is implemented via piezoceramic patches on the beam which produces pure bending moments. The incorporation of the feedback control in this manner leads to a system with an unbounded input term. Approximation methods in this manner leads to a system with an unbounded input term. Approximation methods in the context of linear quadratic regulator (LQR) state space control formulation are discussed and numerical results demonstrating the effectiveness of this approach in computing feedback controls for noise reduction are presented
The synthesis of optimal controls for linear problems with retarded controls
Synthesis of optimal controls for linear systems with retarded control
- …