Structural, optical and magnetic properties of Zn1−xMnxO micro-rod arrays synthesized by spray pyrolysis method

Undoped and Mn-doped ZnO micro-rod arrays were fabricated by the spray pyrolysis method on glass substrates. X-ray diffraction and scanning electron microscopy showed that these micro-rod arrays had a polycrystalline wurtzite structure and high c-axis preferred orientation. Photoluminescence studies at 10 K show that the increase of manganese content leads to a relative decrease in deep level band intensity with respect to undoped ZnO. Magnetic measurements indicated that undoped ZnO was diamagnetic in nature whereas Mn-doped ZnO samples exhibited ferromagnetic behavior at room temperature, which is possibly related to the substitution of Mn ions (Mn2+) for Zn ions in the ZnO lattice

Structural, optical and magnetic properties of Cr doped ZnO microrods prepared by spray pyrolysis

A series of Cr-doped ZnO micro-rod arrays were fabricated by a spray pyrolysis method. X-ray diffraction patterns of the samples showed that the undoped and Cr-doped ZnO microrods exhibit hexagonal crystal structure. Surface morphology analysis of the samples has revealed that pure ZnO sample has a hexagonal microrod morphology. From X-ray photoelectron spectroscopy studies, the Cr 2p3/2 binding energy is found to be 577.34 eV indicating that the electron binding energy of the Cr in ZnO is almost the same as the binding energy of Cr3+ states in Cr2O3. The optical band gap Eg decreases slightly from 3.26 to 3.15 eV with the increase of actual Cr content from x = 0.00 to 4.63 at % in ZnO. Photoluminescence studies at 10 K show that the incorporation of chromium leads to a relative increase of deep level band intensity. It was also observed that Cr doped samples clearly showed ferromagnetic behavior; however, 2.49 % Cr doped ZnO showed remnant magnetization higher than that of 1.07 % and 4.63 % Cr doped samples, while 4.63 % Cr doped ZnO samples had a coercive field higher than the other dopings

Effects of Cu diffusion-doping on structural, optical and magnetic properties of ZnO nanorod arrays grown by VPT

Well-aligned ZnO nanorods were prepared by the vapor phase transport method on Si covered with a ZnO buffer layer. After the nanostructure growth, Cu was doped into the ZnO nanorods by diffusion at three different temperatures and for different times. Undoped and Cu diffusion-doped ZnO samples are highly textured, with the c axis of the wurtzite structure along the growth direction. The incorporation of Cu caused some slight changes in the nanorod alignment, although the wurtzite crystal structure was maintained. X-ray photoelectron spectroscopy measurements revealed that Cu ions were in a divalent state and substituted for the Zn2+ ions of the ZnO matrix. Photoluminescence results at 10 K indicate that the incorporation of copper leads to a relative increase of Cu-related structured green band deep level intensity. Magnetic measurements revealed that both undoped and Cu diffusion-doped ZnO samples exhibited room temperature ferromagnetism. It was also found that bound magnetic polarons play an important role in the appearance of room temperature ferromagnetism in Cu diffusion-doped ZnO nanorods

Layer- and strain-dependent optoelectronic properties of hexagonal AlN

Motivated by the recent synthesis of layered hexagonal aluminum nitride (h-AlN), we investigate its layer- and strain-dependent electronic and optical properties by using first-principles methods. Monolayer h-AlN is a wide-gap semiconductor, which makes it interesting especially for usage in optoelectronic applications. The optical spectra of 1-, 2-, 3-, and 4-layered h-AlN indicate that the prominent absorption takes place outside the visible-light regime. Within the ultraviolet range, absorption intensities increase with the number of layers, approaching the bulk case. On the other hand, the applied tensile strain gradually redshifts the optical spectra. The many-body effects lead to a blueshift of the optical spectra, while exciton binding is also observed for 2D h-AlN. The possibility of tuning the optoelectronic properties via thickness and/or strain opens doors to novel technological applications of this promising material. © 2015 American Physical Society

Enhanced photocatalytic activity of CuWO4 doped TiO2 photocatalyst towards carbamazepine removal under UV irradiation

Abatement of contaminants of emerging concerns (CECs) in water sources has been widely studied employing TiO2 based heterogeneous photocatalysis. However, low quantum energy yield among other limitations of titania has led to its modification with other semiconductor materials for improved photocatalytic activity. In this work, a 0.05 wt.% CuWO4 over TiO2 was prepared as a powder composite. Each component part synthesized via the sol-gel method for TiO2, and CuWO4 by co-precipitation assisted hydrothermal method from precursor salts, underwent gentle mechanical agitation. Homogenization of the nanopowder precursors was performed by zirconia ball milling for 2 h. The final material was obtained after annealing at 500◦C for 3.5 h. Structural and morphological characterization of the synthesized material has been achieved employing X-ray diffraction (XRD), Fourier transform infra-red (FTIR) spectroscopy, Brunauer–Emmett–Teller (BET) N2 adsorption–desorption analysis, Scanning electron microscopy-coupled Energy dispersive X-ray spectroscopy (SEM-EDS), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and UV-Vis diffuse reflectance spectroscopy (UV-vis DRS) for optical characterization. The 0250.05 wt.% CuWO4-TiO2 catalyst was investigated for its photocatalytic activity over carbamazepine (CBZ), achieving a degradation of almost 100% after 2 h irradiation. A comparison with pure TiO2 prepared under those same conditions was made. The effect of pH, chemical scavengers, H2O2 as well as contaminant ion effects (anions, cations), and humic acid (HA) was investigated, and their related influences on the photocatalyst efficiency towards CBZ degradation highlighted accordingly

Defect-induced room temperature ferromagnetism in B-doped ZnO

ZnO microrods were grown on glass substrates by the spray pyrolysis method and boron was doped into the ZnO microrods by diffusion. X-ray diffraction results confirmed that the incorporation of B leads to a slight reduction in the deposit texture. Scanning electron microscopy measurements showed that the morphology of the ZnO samples changed from a microrod to nanocrystalline structure with B-doping. Photoluminescence data indicate that B-doping leads to a relative increase of the unstructured green band intensity. Magnetic measurements revealed that B-doped ZnO samples exhibited room temperature ferromagnetism related to defects, in agreement with first principles theoretical calculations

Structural, optical and Schottky diode properties of Cu2ZnSnS4 thin films grown by two-stage method

CZTS thin film was prepared by a two-stage process comprising sputter deposition of metallic Cu, Zn, and Sn layers followed annealing treatment of the metallic precursors in a sulfur atmosphere at 560 °C for 3 min. The CZTS thin film was investigated in the way of structural, optical and electrical properties. The XRD pattern of Cu-poor and Zn-rich CZTS thin film was dominated by characteristic peaks of kesterite CZTS planes. Raman spectra of the film ensured formation of kesterite CZTS phase and displayed formation of CTS and ZnS phases. Dense and polycrystalline surface features were observed in SEM images of CZTS thin film. Band–band transitions was not observed due to the probable concentration of deep acceptor levels in this material. The diode parameters of Mo/CZTS/Al structure such as ideality factor, barrier height and serial resistance were calculated employing temperature dependent I–V characteristics of Mo/CZTS/Al diode structure. © 2019, Springer Science+Business Media, LLC, part of Springer Nature

Structure and nanomechanical properties of CdTe thin films

CdTe thin films were produced by vacuum evaporation on glass sheets at substrate temperatures of 100 K and 300 K. The structural properties of the CdTe thin films were investigated through X-ray diffraction (XRD) technique and scanning electron microscopy (SEM). The mechanical properties (hardness, modulus and coating adhesion) were measured by nanoindentation and scratching techniques. XRD studies showed that the crystallinity of CdTe films improved with increasing substrate temperature. The grain size increased with the increase of substrate temperature and clearly facetted morphology was observed. The indentation hardness and modulus of CdTe thin films decreased with increasing grain size. The hardness and modulus increased gradually with increasing indentation depth due to the substrate effect. The adhesion of the coating increased with decreasing grain size. © 2007 Elsevier B.V. All rights reserved

Case Report Induction Of Maturogenesis by Partial Pulpotomy: 1 Year Follow-Up

In cariously exposed immature permanent teeth, the treatment choice is controversial in pediatric dentistry. Radical root canal treatment usually appears to be the solution for these teeth. Even partial pulpotomy is a vital treatment for traumatically exposed immature permanent teeth; extending the borders of indication towards cariously exposed immature permanent teeth with reversible pulpitis may abolish the necessity of pulpectomy. This article describes the partial pulpotomy of a cariously affected immature permanent teeth and the follow-up for 1 year. A healthy 11-year-old male patient was referred to Gazi University Faculty of Dentistry Department of Pediatric Dentistry. The patient had reversible pulpitis symptoms on teeth numbered 45. At radiographic examination, immature apex and deep caries lesion were observed and partial pulpotomy was performed by using calcium hydroxide to maintain vitality of the pulp and allow continued development of root dentin expecting the root will attain full maturity. Clinical and radiographic follow-up demonstrated a vital pulp besides not only closure of the apex (apexogenesis), but also physiologic root development (maturogenesis) after 1 year. Partial pulpotomy is an optional treatment for cariously exposed immature permanent teeth for preserving vitality and physiological root development