Multiscale characterisation of the mechanical properties of austenitic stainless steel joints

A multiscale investigation was pursued in order to obtain the strain distribution and evolution during tensile testing both at the macro- and micro-scale for a diffusion bonded 316L stainless steel. The samples were designed for the purpose to demonstrate that the bond line properties were equal or better than the parent material in a sample geometry that was extracted from a larger component. The macroscopic stress-strain curves were coupled to the strain distributions using a camera-based 2D – Digital Image Correlation system. Results showed significant amount of plastic deformation predominantly concentrated in shear bands which were extended over a large region, crossing through the joint area. Yet it was not possible to be certain whether the joint has shown significant plastic deformation. In order to obtain the joints’ mechanical response in more detail, in situ micromechanical testing was conducted in the SEM chamber that allowed areas of 1x1 mm2 and 50x50 mm2 to be investigated. The size of the welded region was rather small to be accurately captured from the camera based DIC system. Therefore a microscale investigation was pursued where the samples were tested within an SEM chamber. Low magnification SEM imaging was utilised in order to cover a viewing area of 1 mm×1 mm while high magnification SEM imaging was employed to provide evidence of the occurrence of plastic deformation within the joint, at an area of just 50 μm×50 μm. The strain evolution over the microstructural level, within the joint and at the base material was obtained. The local strains were highly non-homogeneous through the whole test. Final failure occurred approximately 0.2 mm away from the joint. Large local strains were measured within the joint region, while SEM imaging showed that plastic deformation occurs via the formation of strong slip bands, followed by the activation of additional slip systems upon further plastic deformation which end up in additional slip bands to form on the surface. Plastic deformation occurred by slip and twinning mechanisms. Upon necking, significant out of plane deformations and slip deformation mechanisms were observed which suggested that plastic deformation was also happening at the last stages of damage evolution for the specific alloy. This was also evident from the large difference between the 600 MPa UTS stress value and the low stress values before final failure (which in many cases was below 30 MPa)

Integrated Hepatitis C Care for People Who Inject Drugs (Heplink): Protocol for a Feasibility Study in Primary Care (Preprint)

Background: Hepatitis C virus (HCV) infection is a major cause of chronic liver disease and death. Drug use remains the significant cause of new infections in the European Union, with estimates of HCV antibody prevalence among people who inject drugs ranging from 5% to 90% in 29 European countries. In Ireland and the European Union, primary care is a key area to focus efforts to enhance HCV diagnosis and treatment among people who inject drugs. Objective: The Heplink study aims to improve HCV care outcomes among opiate substitution therapy (OST) patients in general practice by developing an integrated model of HCV care and evaluating its feasibility, acceptability, and likely efficacy. Methods: The integrated model of care comprises education of community practitioners, outreach of an HCV-trained nurse into general practitioner (GP) practices, and enhanced access of patients to community-based evaluation of their HCV disease (including a novel approach to diagnosis, that is, Echosens FibroScan Mini 430). A total of 24 OST-prescribing GP practices were recruited from the professional networks and databases of members of the research consortium. Patients were eligible if they are aged ≥18 years, on OST, and attend the practice for any reason during the recruitment period. Baseline data on HCV care processes and outcomes were extracted from the clinical records of participating patients. Results: This study is ongoing and has the potential to make an important impact on patient care and provide high-quality evidence to help GPs make important decisions on HCV testing and onward referral. Conclusions: A substantial proportion of HCV-positive patients on OST in general practice are not engaged with specialist hospital services but qualify for direct-acting antiviral drugs treatment. The Heplink model has the potential to reduce HCV-related morbidity and mortality. Registered Report Identifier: RR1-10.2196/904

Effect of Weld Schedule on the Residual Stress Distribution of Boron Steel Spot Welds

Press-hardened boron steel has been utilized in anti-intrusion systems in automobiles, providing high strength and weight-saving potential through gage reduction. Boron steel spot welds exhibit a soft heat-affected zone which is surrounded by a hard nugget and outlying base material. This soft zone reduces the strength of the weld and makes it susceptible to failure. Additionally, different welding regimes lead to significantly different hardness distributions, making failure prediction difficult. Boron steel sheets, welded with fixed and adaptive schedules, were characterized. These are the first experimentally determined residual stress distributions for boron steel resistance spot welds which have been reported. Residual strains were measured using neutron diffraction, and the hardness distributions were measured on the same welds. Additionally, similar measurements were performed on spot welded DP600 steel as a reference material. A correspondence between residual stress and hardness profiles was observed for all welds. A significant difference in material properties was observed between the fixed schedule and adaptively welded boron steel samples, which could potentially lead to a difference in failure loads between the two boron steel welds

Characterization of Loading Responses and Failure Loci of a Boron Steel Spot Weld

Boron steel, classed as an ultra high-strength steel (UHSS), has been utilized in anti-intrusion systems in automobiles, providing high strength and weight-saving potential through gage reduction. UHSS spot welds exhibit unique hardness distributions, with a hard nugget and outlying base material, but with a soft heat-affected zone in-between these regions. This soft zone reduces the strength of the weld and makes it susceptible to failure. Due to the interaction of various weld zones that occurs during loading, there is a need to characterize the loading response of the weld for accurate failure predictions. The loading response of certain weld zones, as well as failure loci, was obtained through physical simulation of the welding process. The results showed a significant difference in mechanical behavior through the weld length. An important result is that instrumented indentation was shown to be a valid, quantitative method for verifying the accuracy with which weld microstructure has been recreated with regard to the target weld microstructure

Stellar coronal astronomy - a review

Coronal astronomy is by now a fairly mature discipline, with a quarter century having gone by since the detection of the first stellar X-ray coronal source (Capella), and having benefitted from a series of major orbiting observing facilities. Several observational characteristics of coronal X-ray and EUV emission have been solidly established through extensive observations, and are by now common, almost text-book, knowledge. At the same time the implications of coronal astronomy for broader astrophysical questions (e.g. Galactic structure, stellar formation, stellar structure, etc.) have become appreciated. The interpretation of stellar coronal properties is however still often open to debate, and will need qualitatively new observational data to book further progress. In the present review we try to recapitulate our view on the status of the field at the beginning of a new era, in which the high sensitivity and the high spectral resolution provided by Chandra and XMM-Newton will address new questions which were not accessible before.Comment: Space Science Reviews, in press, 132 pages (full paper available at ftp://astro.esa.int/pub/ffavata/Papers/ssr-preprint.pdf

'HepCheck Dublin': An Intensified Hepatitis C Screening Programme in a Homeless Population Demonstrates the Need for Alternative Models of Care

Background: Hepatitis C virus (HCV) is one of the main causes of chronic liver disease worldwide. Prevalence of HCV in homeless populations ranges from 3.9% to 36.2%. The HepCheck study sought to investigate and establish the characterisation of HCV burden among individuals who attended an intensified screening programme for HCV in homeless services in Dublin, Ireland. Methods: The HepCheck study was conducted as part of a larger European wide initiative called HepCare Europe. The study consisted of three phases; 1) all subjects completed a short survey and were offered a rapid oral HCV test; 2) a convenience sample of HCV positive participants from phase 1 were selected to complete a survey on health and social risk factors and 3) subjects were tracked along the referral pathway to identify whether they were referred to a specialist clinic, attended the specialist clinic, were assessed for cirrhosis by transient elastography (Fibroscan) and were treated for HCV. Results: 597 individuals were offered HCV screening, 73% were male and 63% reported having had a previous HCV screening. We screened 538 (90%) of those offered screening, with 37% testing positive. Among those who tested positive, 112 (56%) were ‘new positives’ and 44% were ‘known positives’. Undiagnosed HCV was prevalent in 19% of the study sample. Active past 30-day drug use was common, along with attendance for drug treatment. Unstable accommodation was the most common barrier to attending specialist appointments and accessing treatment. Depression and anxiety, dental problems and respiratory conditions were common reported health problems. 46 subjects were referred to specialised services and two subjects completed HCV treatment. Conclusions: This study demonstrates that the current hospital-based model of care is inadequate in addressing the specific needs of a homeless population and emphasises the need for a community-based treatment approach. Findings are intended to inform HepCare Europe in their development of a community-based model of care in order to engage with homeless individuals with multiple co-morbidities including substance abuse, who are affected by or infected with HCV