16 research outputs found
Highly Reflective Dielectric Back Reflector for Improved Efficiency of Tandem Thin-Film Solar Cells
We report on the prototyping and development of a highly reflective dielectric back reflector for application in thin-film solar cells. The back reflector is fabricated by Snow Globe Coating (SGC), an innovative, simple, and cheap process to deposit a uniform layer of TiO2 particles which shows remarkably high reflectance over a broad spectrum (average reflectance of 99% from 500 nm to 1100 nm). We apply the highly reflective back reflector to tandem thin-film silicon solar cells and compare its performance with conventional ZnO:Al/Ag reflector. By using SGC back reflector, an enhancement of 0.5 mA/cm2 in external quantum efficiency of the bottom solar cell and an absolute value of 0.2% enhancement in overall power conversion efficiency are achieved. We also show that the increase in power conversion efficiency is due to the reduction of parasitic absorption at the back contact; that is, the use of the dielectric reflector avoids plasmonic losses at the reference ZnO:Al/Ag back reflector. The Snow Globe Coating process is compatible with other types of solar cells such as crystalline silicon, III–V, and organic photovoltaics. Due to its cost effectiveness, stability, and excellent reflectivity above a wavelength of 400 nm, it has high potential to be applied in industry
Substrate-induced coagulation (SIC) of nano-disperse titania in non-aqueous media : the dispersibility and stability of titania in N-methyl-2-pyrrolidinone
Dispersions of 1 wt% titandioxide (titania or TiO2) were investigated with respect to their stability in non-aqueous media. The objective of this work was to find conditions for the substrate-induced coagulation (SIC) process in N-methyl-2-pyrrolidinone (NMP). The SIC process is a dip-coating process that enhances adsorption of fine dispersed particles on a pre-conditioned surface. The wetting behavior of titania and NMP was investigated by the powder contact angle method. The absorption process of the polar solvent NMP on the acid oxide TiO2and Aerosol OT (AOT) (bis-2-ethylhexyl sodium sulfosuccinate) was also investigated and a polar or hydrophilic interaction was found. The stability of titania in NMP dispersions and the influence of the solvent AOT and the electrolyte LiCl was investigated. By studying the electrophoretic mobilities of titania particles in NMP and the influence on solutes by the electrophoretic method phase analysis light scattering (PALS) and the electroacoustic method this paper explores suitable conditions for non-aqueous substrate-induced coagulation of titania
Substrate-induced coagulation (SIC) of nano-disperse carbon black in non-aqueous media : the dispersibility and stability of carbon black in N-methyl-2-pyrrolidinone
Texture effects in the delithiation of lithium cobalt oxide
The effects of aqueous delithiation of lithium cobalt oxide crystals on the crystal texture and etching patterns has been studied by electron microscopy, x-ray and neutron diffraction at high resolution. The delithiation proceeds to exfoliation and in the process textural patterns that appear have been associated with periodic strains in the crystals developed by the delithiation
Substrate-induced coagulation (SIC) of nano-disperse carbon black in non-aqueous media : a method of manufacturing highly conductive cathode materials for Li-ion batteries by self-assembly
Substrate-induced coagulation (SIC) is a coating process based on self-assembly for coating different surfaces with fine particulate materials. The particles are dispersed in a suitable solvent and the stability of the dispersion is adjusted by additives. When a surface, pre-treated with a flocculant e.g. a polyelectrolyte, is dipped into the dispersion, it induces coagulation resulting in the deposition of the particles on the surface. A non-aqueous SIC process for carbon coating is presented, which can be performed in polar, aprotic solvents such as N-Methyl-2- pyrrolidinone (NMP). Polyvinylalcohol (PVA) is used to condition the surface of substrates such as mica, copperfoil, silicon-wafers and lithiumcobalt oxide powder, a cathode material used for Li-ion batteries. The subsequent SIC carbon coating produces uniform layers on the substrates and causes the conductivity of lithiumcobalt oxide to increase drastically, while retaining a high percentage of active battery material.<br /
Chemical delithiation and exfoliation of LixCoO2
Progressive chemical.delithiation of commercially available lithium cobalt oxide (LixCoO2) showed consecutive changes in the crystal properties. Rietveld refinement of high resolution X-ray and neutron diffraction revealed an increased lattice parameter c and a reduced lattice parameter a for chemically delithiated samples. Using electron microscopy we have also followed the changes in the texture of the samples towards what we have found is a critical layer stoichiometry of about LixCoO2 with x=1/3 that causes the grains to exfoliate. The pattern of etches by delithiation suggests that unrelieved strain fields may produce chemical activity
Substrate-induced coagulation (SIC) of nano-disperse alumina in non-aqueous media: The dispersibility and stability of alumina in N-methyl-2-pyrrolidinone
This work investigated colloidal properties such as the zeta-potential, the electrophoretic mobilities and the wetting behaviour of alumina dispersed in non-aqueous media. Non-aqueous dispersions of alumina were prepared in the solvent N-methyl-2-pyrrolidinone (NMP). The wetting behaviour of alumina in NMP was characterized by the powder contact angle method and the Wilhemy plate method. The behaviour of the dispersion should provide information for the development of a substrate-induced coagulation (SIC) coating process of nano-sized alumina in non-aqeous media. SIC is a dip-coating process that coats pretreated but chemically different surfaces with nano-sized particles. It was found that the anionic surfactant dioctyl sulfosuccinate (AOT) had no stabilizing effect on alumina dispersed in NMP
Enhanced light trapping in solar cells using snow globe coating
A novel method, snow globe coating, is found to show significant enhancement of the short circuit current JSC (35%) when applied as a scattering back reflector for polycrystalline silicon thin-film solar cells. The coating is formed from high refractive index titania particles without containing binder and gives close to 100% reflectance for wavelengths above 400 nm. Snow globe coating is a physicochemical coating method executable in pH neutral media. The mild conditions of this process make this method applicable to many different types of solar cells
Highly Reflective Dielectric Back Reflector for Improved Efficiency of Tandem Thin-Film Solar Cells
We report on the prototyping and development of a highly reflective dielectric back reflector for application in thin-film solar cells. The back reflector is fabricated by Snow Globe Coating (SGC), an innovative, simple, and cheap process to deposit a uniform layer of TiO2 particles which shows remarkably high reflectance over a broad spectrum (average reflectance of 99% from 500 nm to 1100 nm). We apply the highly reflective back reflector to tandem thin-film silicon solar cells and compare its performance with
conventional ZnO:Al/Ag reflector. By using SGC back reflector, an enhancement of 0.5 mA/cm2 in external quantum efficiency of the bottom solar cell and an absolute value of 0.2% enhancement in overall power conversion efficiency are achieved.We also show
that the increase in power conversion efficiency is due to the reduction of parasitic absorption at the back contact; that is, the use
of the dielectric reflector avoids plasmonic losses at the reference ZnO:Al/Ag back reflector. The Snow Globe Coating process is
compatible with other types of solar cells such as crystalline silicon, III–V, and organic photovoltaics. Due to its cost effectiveness,
stability, and excellent reflectivity above a wavelength of 400 nm, it has high potential to be applied in industry
Chemical delithiation and exfoliation of LixCoO2
AbstractProgressive chemical .delithiation of commercially available lithium cobalt oxide (LiCoO2) showed consecutive changes in the crystal properties. Rietveld refinement of high resolution X-ray and neutron diffraction revealed an increased lattice parameter c and a reduced lattice parameter a for chemically delithiated samples. Using electron microscopy we have also followed the changes in the texture of the samples towards what we have found is a critical layer stoichiometry of about LixCoO2 with x=1/3 that causes the grains to exfoliate. The pattern of etches by delithiation suggests that unrelieved strain fields may produce chemical activity