11 research outputs found
Recommended from our members
Response surface methodology for predicting the dimethylphenol removal from wastewater via reverse osmosis process
YesReverse Osmosis (RO) process can be considered as one of the intensively used pioneering equipment for reusing wastewater of several applications. The recent study presented the development of an accurate model for predicting the dimethylphenol removal from wastewater via RO process. The Response Surface Methodology (RSM) was applied to carry out this challenge based on actual experimental data collected from the literature. The independent variables considered are the inlet pressure (5.83-13.58) atm, inlet temperature (29.5-32) ° C, inlet feed flow rate (2.166-2.583) × 10-4 m3/s, and inlet concentration (0.854-8.049) × 10-3 kmol/m3 and the dimethylphenol removal is considered as the response variable. The analysis of variance showed that the inlet temperature and feed flow rate have a negative influence on dimethylphenol removal from wastewater while the inlet pressure and concentration show a positive influence. In this regard, F-value of 240.38 indicates a considerable contribution of the predicted variables of pressure and concentration against the process dimethylphenol rejection. Also, the predicted R2 value of 0.9772 shows the high accuracy of the model. An overall assessment of simulating the performance of RO process against the operating parameters has been systematically demonstrated using the proposed RSM model
The effect of adding natural materials waste on the mechanical properties and water absorption of epoxy composite using grey relations analysis
Recently, there has been a tendency for scientific studies to deal with natural materials as fillers and reinforcement for polymer composites, which are used in many different applications due to their environmentally friendly properties when compared to synthetic materials. The current study aims to preserve the environment by dealing with natural materials and their influence on the mechanical properties and water absorption property of the polymer composites. In this study, epoxy composites were produced from local natural sourced non-hazardous raw natural materials using grey relational analysis (GRG). The materials used for fabrication include micro-filler of pollen palm 50 μm, seashell 75 μm and epoxy resin. Nine different composites were prepared using pollen palm and seashell as reinforcement material by varying the wt % of the micro-filler. Rule of the mixture was used for formulation and wt % of (0.5, 1 and 1.5) % reinforcement and 99.5, 99 and 98.5 % epoxy (binder) were used for composites. Grey relational analysis was conducted in order to scale the multi-response performance to a single response. The results indicate that optimum performance can be achieved with the addition of 1.5 wt % micro-filler of seashell, which achieved the first rank, while the second rank achieved by 0.5 wt % micro-filler of palm pollen and seashell when compared to other composites. The addition of micro-fillers has improved greatly the mechanical properties of epoxy composites. The loading of micro-fillers has influenced the water absorption property of composites based epoxy in ascending orde
Recommended from our members
Scope and limitations of modelling, simulation, and optimisation of a spiral wound reverse osmosis process-basedwater desalination
YesThe reverse osmosis (RO) process is one of the best desalination methods, using membranes to reject several impurities from seawater and brackish water. To systematically perceive the transport phenomena of solvent and solutes via the membrane texture, several mathematical models have been developed. To date, a large number of simulation and optimisation studies have been achieved to gauge the influence of control variables on the performance indexes, to adjust the key variables at optimum values, and to realise the optimum production indexes. This paper delivers an intensive review of the successful models of theROprocess and both simulation and optimisation studies carried out on the basis of the models developed. In general, this paper investigates the scope and limitations of the RO process, as well as proving the maturity of the associated perspective methodologies
Evaluation of solar energy powered seawater desalination pro-cesses: A review
YesSolar energy, amongst all renewable energies, has attracted inexhaustible attention all over the world as a supplier of sustainable energy. The energy requirement of major seawater desalination processes such as multistage flash (MSF), multi-effect distillation (MED) and reverse osmosis (RO) are fulfilled by burning fossil fuels, which impact the environment significantly due to the emission of greenhouse gases. The integration of solar energy systems into seawater desalination processes is an attractive and alternative solution to fossil fuels. This study aims to (i) assess the progress of solar energy systems including concentrated solar power (CSP) and photovoltaic (PV) to power both thermal and membrane seawater desalination processes including MSF, MED, and RO and (ii) evaluate the economic considerations and associated challenges with recommendations for further improvements. Thus, several studies on a different combination of seawater desalination processes of solar energy systems are reviewed and analysed concerning specific energy consumption and freshwater production cost. It is observed that although solar energy systems have the potential of reducing carbon footprint significantly, the cost of water production still favours the use of fossil fuels. Further research and development on solar energy systems are required to make their use in desalination economically viable. Alternatively, the carbon tax on the use of fossil fuels may persuade desalination industries to adopt renewable energy such as solar
Scope and Limitations of Modelling, Simulation, and Optimisation of a Spiral Wound Reverse Osmosis Process-Based Water Desalination
The reverse osmosis (RO) process is one of the best desalination methods, using membranes to reject several impurities from seawater and brackish water. To systematically perceive the transport phenomena of solvent and solutes via the membrane texture, several mathematical models have been developed. To date, a large number of simulation and optimisation studies have been achieved to gauge the influence of control variables on the performance indexes, to adjust the key variables at optimum values, and to realise the optimum production indexes. This paper delivers an intensive review of the successful models of the RO process and both simulation and optimisation studies carried out on the basis of the models developed. In general, this paper investigates the scope and limitations of the RO process, as well as proving the maturity of the associated perspective methodologies
Thermodynamic Limitations and Exergy Analysis of Brackish Water Reverse Osmosis Desalination Process
The reverse osmosis (RO) process is one of the most popular membrane technologies for the generation of freshwater from seawater and brackish water resources. An industrial scale RO desalination consumes a considerable amount of energy due to the exergy destruction in several units of the process. To mitigate these limitations, several colleagues focused on delivering feasible options to resolve these issues. Most importantly, the intention was to specify the most units responsible for dissipating energy. However, in the literature, no research has been done on the analysis of exergy losses and thermodynamic limitations of the RO system of the Arab Potash Company (APC). Specifically, the RO system of the APC is designed as a medium-sized, multistage, multi pass spiral wound brackish water RO desalination plant with a capacity of 1200 m3/day. Therefore, this paper intends to fill this gap and critically investigate the distribution of exergy destruction by incorporating both physical and chemical exergies of several units and compartments of the RO system. To carry out this study, a sub-model of exergy analysis was collected from the open literature and embedded into the original RO model developed by the authors of this study. The simulation results explored the most sections that cause the highest energy destruction. Specifically, it is confirmed that the major exergy destruction happens in the product stream with 95.8% of the total exergy input. However, the lowest exergy destruction happens in the mixing location of permeate of the first pass of RO desalination system with 62.28% of the total exergy input
Recommended from our members
Performance evaluation of a medium-scale industrial reverse osmosis brackish water desalination plant with different brands of membranes. A simulation study
NoBrackish water can be considered an important source of fresh water, via desalination, especially for arid districts. Reverse Osmosis (RO) process has been successfully used to produce fresh water from brackish water sources. However, there is still the challenge of improving the performance of multistage RO desalination plants. From the selection of the RO configurations to the selection of the appropriate type of membranes and the operating conditions at the end determines the performance of RO process in terms of recovery, salt rejection, energy consumptions and ultimately the cost of production of freshwater. Using model-based simulation, this work attempts to investigate the most suitable types of membranes for an industrial scale RO plant from a set of different membrane brands that would attain the highest-performance at lowest specific energy consumption (SEC). As a case study, we considered a multistage multi-pass medium-scale RO plant (1200 m3/day) of Arab Potash Company (APC, Jordan) which produces high quality water for the boilers after pre-treatment stage. The simulation results confirmed that employment of the Filmtec BW30LE-440 would increase water recovery by about 22% besides reducing the product salinity and SEC by about 15% and 10%, respectively compared to the existing membrane
A Review of Recent Improvements, Developments, and Effects of Using Phase-Change Materials in Buildings to Store Thermal Energy
When it comes to guaranteeing appropriate performance for buildings in terms of energy efficiency, the building envelope is a crucial component that must be presented. When a substance goes through a phase transition and either gives out or absorbs an amount of energy to provide useful heat or cooling, it is called a phase-change material, or PCM for short. Transitions often take place between the matter’s solid and liquid states. Buildings use PCMs for a variety of purposes, including thermal comfort, energy conservation, managing the temperature of building materials, reducing cooling/heating loads, efficiency, and thermal load shifting. Improved solutions are applied using new method and approach investigations. Undoubtedly, researching and applying PCM use in building applications can help create buildings that are more energy-efficient and environmentally friendly, while also increasing thermal comfort and consuming less energy. It provides a possible answer to the problems posed by climate change, rising energy demand in the built environment, and energy use optimisation. However, it is true that no particular research has yet been conducted to thoroughly analyse the linked PCM applications in the building industry. Thus, the principal tactics are addressed in this paper to determine current and efficient methods for employing PCMs in buildings to store thermal energy. By gathering around 50 instances from the open literature, this study conducts a thorough assessment of the up-to-date studies between 2016 and 2023 that used PCMs as thermal energy storage in building applications. As a result, this review aims to critically evaluate the PCM integration in buildings for thermal energy storage, identify a number of issues that require more research, and draw some important conclusions from the body of literature. Specifically, the building envelope roof and external wall uses of PCMs are highlighted in this research. Applications, general and desired characteristics, and PCM types and their thermal behaviour are described. In comparison to a traditional heat storage tank that simply contains water, this review indicates that a water storage tank containing 15% PCM improves heat storage by 70%. Also, less than 7 °C of internal air temperature was reduced by the PCMs in the walls, which avoided summer warming. Finally, using PCM for space cooling resulted in substantial energy savings across the various seasons
The Effect of Adding Natural Materials Waste on the Mechanical Properties and Water Absorption of Epoxy Composite Using Grey Relations Analysis
Recently, there has been a tendency for scientific studies to deal with natural materials as fillers and reinforcement for polymer composites, which are used in many different applications due to their environmentally friendly properties when compared to synthetic materials. The current study aims to preserve the environment by dealing with natural materials and their influence on the mechanical properties and water absorption property of the polymer composites. In this study, epoxy composites were produced from local natural sourced non-hazardous raw natural materials using grey relational analysis (GRG). The materials used for fabrication include micro-filler of pollen palm 50 μm, seashell 75 μm and epoxy resin. Nine different composites were prepared using pollen palm and seashell as reinforcement material by varying the wt % of the micro-filler. Rule of the mixture was used for formulation and wt % of (0.5, 1 and 1.5) % reinforcement and 99.5, 99 and 98.5 % epoxy (binder) were used for composites. Grey relational analysis was conducted in order to scale the multi-response performance to a single response. The results indicate that optimum performance can be achieved with the addition of 1.5 wt % micro-filler of seashell, which achieved the first rank, while the second rank achieved by 0.5 wt % micro-filler of palm pollen and seashell when compared to other composites. The addition of micro-fillers has improved greatly the mechanical properties of epoxy composites. The loading of micro-fillers has influenced the water absorption property of composites based epoxy in ascending orde
Inverted Solar Stills: A Comprehensive Review of Designs, Mathematical Models, Performance, and Modern Combinations
Fresh water is scarce, making it a worldwide issue. In order to address global freshwater demand, a filtration technique is needed. Solar distillation (SD) that purifies brackish and subterranean water has been proven to be a promising green technology. It produces distilled water which can be used as potable water for drinking and other purposes. The designs, operations, and configurations of several inverted solar stills are thoroughly examined in this article. All techniques for solar water distillation to separate saltwater from freshwater have the same fundamental idea. It has been demonstrated that for a specified mass of water in the top basin, the daily output of an inverted absorber double-basin solar still (IASS) grows with increasing water depth in the bottom basin. Nevertheless, as the water depth in the bottom basin rises from 1 cm to 5 cm, the output of an inverted absorber double-basin solar system falls by about 27%. At water depths of 4, 6, and 8 cm, the daily yields from inverted absorber solar stills paired with a refrigeration cycle (RIASS) were 6.4, 10.08, and 9.5 L/day, respectively. The results also showed a substantial rise in water temperature in the inverted absorber solar still as a result of lower bottom heat loss and larger absorptivity. In this study, the emphasis on energy, efficiency, and environmental concerns remains with the modified multi-wick basin-type inverted absorber solar panel. The performance of the inverted trickling solar still was assessed with a 60 ppm average salinity under various sun radiation, feed water flow rate, and existence conditions for natural convection. It was found that the still could produce 2.55 L/day m2 of fresh water, a 15% increase. Brackish water with a salinity of 6000 ppm was used to test the still in November at tilt angles of 47° and 32°. Condensate production at the specified angles was 2.8 and 2 L/d, respectively. A total output of 6.907, 5.681, and 4.650 kg/m2/day was also generated using the modified multi-wick basin-type inverted absorber solar still (MMWBIASS) at water depths of 1, 2, and 3 cm, respectively. With black cotton wicks, the MMWBIASS had a total thermal efficiency of 34.04%, 28.17%, and 23.61%