PEMBENTUKAN VERBA MELALUI AFIKSASI DALAM BAHASA TERNATE

Penelitian ini merupakan penelitian kualitatif deskriptif yang bertujuan mendeskripsikan prosemorfologis khususnya pada pembentukan verba dalam bahasa Ternate. Pembentukan verbdimaksud hanya pada pembentukan yang dibatasi dari bentuk dasar kelas kata utama (nomina,adjektiva dan verba). Metode yang digunakan dalam penelitian ini adalah metode simak dajuga pemanfaatan metode introspektif sebagai lumbung data. Hasil penelitian ini menunjukbahwa bahasa Ternate hanya mengenal satu jenis afiks yakni prefiks. Prefiks yang terdapadalam bahasa Ternate yang dimaksud, dalam hal ini terkait pembentukan verba, adalah {ma{si-} dan {maku-}, dengan fungsinya masing-masing. Prefiks {ma-} lebih cenderung padapembentukan verba yang bersifat intransitif-reflektif. Prefiks {si-} lebih cenderung padpembentukan verba dengan sifat transitif-beneaktif. Sementara, prefiks {maku-} berfungssebagai pembentuk verba resiprokal. Semua verba turunan dari hasil prefiksasi tersebumerupakan verba bentuk aktif. Peneliti, dalam penelitian ini, tidak menemukan afpembentukan verba pasif dalam bahasa Ternate

One-dimensional backreacting holographic p-wave superconductors

We analytically as well as numerically study the properties of one-dimensional holographic p- wave superconductors in the presence of backreaction. We employ the Sturm-Liouville eigenvalue problem for the analytical calculation and the shooting method for the numerical investigations. We apply the AdS3/CFT2 correspondence and determine the relation between the critical temperature Tc and the chemical potential \mu for different values of mass m of charged spin-1 field and backreacting parameters. We observe that the data of both analytical and numerical studies are in good agreement. We find out that increasing the backreaction as well as the mass parameter cause the greater values for Tc/ \mu. Therefore, it makes the condensation harder to form. In addition, the analytical and numerical approaches show that the value of the critical exponent \beta is 1/2 which is the same as in the mean field theory. Moreover, both methods confirm the exhibition of a second order phase transition

Design and Fabricate Filament Winding Machine and Analysis of Cotton/Epoxy and Pandanus/Epoxy

This project concerned with filament wound cotton/epoxy and pandanus/epoxy composite tubes. Monofilament winding machine has been designed and fabricated. It is later used in fabricating the composite tubes. The performance of this machine was measured. The results revealed that the winding angle depended primarily on the carriage speed traversing at speed synchronised with mandrel rotation. Also, the efficiency of the machine showed that winding at high angles relative to rotational axis was very high (i.e. at 90° the efficiency is 100%). Winding at low angles (parallel to rotational axis) was difficult. The surface finish depended on the fibre tension, the wiping process and band formation 0. e. smooth surface finish at 4.4 kN). The behaviour of filament wound cotton/epoxy and pandanus/epoxy composite tubes was studied experimentally. Circular cylindrical of cotton/epoxy and pandanus/epoxy were loaded in uni-axial compression. The test results show that cotton/epoxy hoop tubes the maximum strength was found to be 13kN and for the 80° cotton/epoxy tubes was found to be 10.6kN. For the pandanus/epoxy hoop tube the maximum strength was found to be 0.3kN. Flat specimens were also prepared from wound tubes and loaded in uni-axial tension. The cotton/epoxy composite tubes were tested under internal pressure. The results show that the maximum pressure that the tube can be withstand was found to be 5 bar. Maximum stress and maximum strain theories are used to predict the failure of these tubes. Finite element method also used in the analysis of cotton/epoxy composite tubes. The uni-axial tensile test results show that the mean modulus was found to be 3 867.6 MPa for the 80° laminated tensile test specimens and 1067.0 MPa for hoop (90°) laminated tensile test specimens. The maximum strain mean in 80° and 90° laminated tensile specimens are essentially the same (0.1). The urn-axial compression test results show that in the condition of hoop (90°) laminated tubes and 80° laminated tubes the load-displacement curve is linearly up to initial failure