On-Chip Immunoassay for Determination of Urinary Albumin

An immunoassay performed on a portable microfluidic device was evaluated for the determination of urinary albumin. An increase in absorbance at 500 nm resulting from immunoagglutination was monitored directly on the poly(dimethylsiloxane) (PDMS) microchip using a portable miniature fibre-optic spectrometer. A calibration curve was linear up to 10 mg L–1 (r2 = 0.993), with a detection limit of 0.81 mg L–1 (S/N = 3). The proposed system showed good precision, with relative standard deviations (RSDs) of 5.1%, when evaluated with 10 mg L–1 albumin (n = 10). Determination of urinary albumin with the proposed system gave results highly similar to those determined by the conventional spectrophotometric method using immunoturbidimetric detection (r2 = 0.995; n = 15)

Optical H2 sensing properties of vertically aligned Pd/WO3 nanorods thin films deposited via glancing angle rf magnetron sputtering

In this work, the optical H2-sensing properties of Pd/tungsten trioxide (WO3) nanorods prepared by rf magnetron sputtering with glancing-angle deposition (GLAD) technique are investigated. From grazing-incidence X-ray diffraction and field emission scanning electron microscopic characterizations, annealed WO3 structure deposited on a quartz substrate at glancing angle of 85° exhibited polycrystalline monoclinic crystal structure with uniform partially isolated columnar nanorod morphology. The nanorods have the average length, diameter and rod separation of around 400 nm, 50 nm and 20 nm, respectively. The developed sensors show remarkable gasochromic absorbance response when exposed to H2. Cumulative absorbance in 650–1000 nm wavelength range is increased by approximately 51% toward H2 with 0.1% concentration in synthetic air, which is more than an order of magnitude higher than that of WO3 dense film prepared by conventional sputtering method. Moreover, WO3 nanorod based sensor is much more promising for practical use due to its much faster response. Therefore, the developed Pd/WO3 nanorod based optical sensors are highly potential for low H2 concentration sensing with highly sensitivity, fast and stable responses and low operating temperature

3D-printed PLA/PEO blend as biodegradable substrate coating with CoCl2 for colorimetric humidity detection

This study aimed to fabricate biodegradable substrate with colorimetric humidity indicator for detective moisture in food packaging. The poor properties of poly(lactic acid) (PLA) were enhanced by melt blending PLA with non-toxic poly(ethylene oxide) PEO at 180 °C. Specifically, three-dimensional (3D) substrates of PLA/PEO blends were fabricated by solvent-cast 3D printing. Furthermore, cobalt chloride (CoCl2) solution was printed onto the substrate with an inkjet printer to serve as a colorimetric humidity sensing indicator. It found that the flexibility and thermal stability of the PLA were improved and the hydrophilicity was increased with an increase in PEO content. Color changes and the sensitivity of this material were confirmed using image analysis and total color difference. The CoCl2 indicator displayed color changes that ranged from blue to pink under ambient conditions (above 60%RH), revealing suitable potential for frozen food packaging material with aim to detect amount of moisture in the packaging

High Sensitivity Electrochemical Cholesterol Sensor Utilizing a Vertically Aligned Carbon Nanotube Electrode with Electropolymerized Enzyme Immobilization

In this report, a new cholesterol sensor is developed based on a vertically aligned CNT electrode with two-step electrochemical polymerized enzyme immobilization. Vertically aligned CNTs are selectively grown on a 1 mm2 window of gold coated SiO2/Si substrate by thermal chemical vapor deposition (CVD) with gravity effect and water-assisted etching. CNTs are then simultaneously functionalized and enzyme immobilized by electrochemical polymerization of polyaniline and cholesterol enzymes. Subsequently, ineffective enzymes are removed and new enzymes are electrochemically recharged. Scanning electron microscopic characterization indicates polymer-enzyme nanoparticle coating on CNT surface. Cyclic voltammogram (CV) measurements in cholesterol solution show the oxidation and reduction peaks centered around 450 and −220 mV, respectively. An approximately linear relationship between the cholesterol concentration and the response current could be observed in the concentration range of 50–300 mg/dl with a sensitivity of approximately 0.22 μA/mg·dl−1, which is considerably higher compared to previously reported CNT bioprobe. In addition, good specificity toward glucose, uric acid acetaminophen and ascorbic acid have been obtained. Moreover, sensors have satisfactory stability, repeatability and life time. Therefore, the electropolymerized CNT bioprobe is promising for cholesterol detection in normal cholesterol concentration in human blood

Metamaterial-based microfluidic sensor for dielectric characterization

A microfluidic sensor is implemented from a single split-ring resonator (SRR), a fundamental building block of electromagnetic metamaterials. At resonance, an SRR establishes an intense electric field confined within a deeply subwavelength region. Liquid flowing in a micro-channel laid on this region can alter the local field distribution and hence affect the SRR resonance behavior. Specifically, the resonance frequency and bandwidth are influenced by the complex dielectric permittivity of the liquid sample. The empirical relation between the sensor resonance and the sample permittivity can be established, and from this relation, the complex permittivity of liquid samples can be estimated. The technique is capable of sensing liquid flowing in the channel with a cross-sectional area as small as (0.001λ0)2, where λ0 denotes the free-space wavelength of the wave excitation. This work motivates the use of SRR-based microfluidic sensors for identification, classification, and characterization of chemical and biochemical analytes. © 2012 Elsevier B.V.Withawat Withayachumnankul, Kata Jaruwongrungsee, Adisorn Tuantranont, Christophe Fumeaux, Derek Abbot

Multi-Walled Carbon Nanotube-Doped Tungsten Oxide Thin Films for Hydrogen Gas Sensing

In this work we have fabricated hydrogen gas sensors based on undoped and 1 wt% multi-walled carbon nanotube (MWCNT)-doped tungsten oxide (WO3) thin films by means of the powder mixing and electron beam (E-beam) evaporation technique. Hydrogen sensing properties of the thin films have been investigated at different operating temperatures and gas concentrations ranging from 100 ppm to 50,000 ppm. The results indicate that the MWCNT-doped WO3 thin film exhibits high sensitivity and selectivity to hydrogen. Thus, MWCNT doping based on E-beam co-evaporation was shown to be an effective means of preparing hydrogen gas sensors with enhanced sensing and reduced operating temperatures. Creation of nanochannels and formation of p-n heterojunctions were proposed as the sensing mechanism underlying the enhanced hydrogen sensitivity of this hybridized gas sensor. To our best knowledge, this is the first report on a MWCNT-doped WO3 hydrogen sensor prepared by the E-beam method

Investigation of NiO film by sparking method under a magnetic field and NiO/ZnO heterojunction

Nickel oxide (NiO) film receives attention from the field of optoelectronics due to its wide band gap and high transparency. By using a sparking method, the deposition of the NiO film is facile and unique. However, the NiO film made by the sparking method indicates a porous surface with an agglomeration of its particles. In order to reduce the porousness of the NiO film, the assistance of a permanent magnet in the sparking apparatus is presented. Here, we report the investigation of the NiO film and the p-NiO/n-ZnO heterojunction deposited by the sparking method under a magnetic field. Our results demonstrate that the porosity of the NiO film was reduced by increasing the magnitude of a magnetic field from 0 mT to 375 mT. Furthermore, the crystallinity and the electrical properties of the NiO film are improved by the influent of a magnetic field. For heterojunction, the best device shows the rectification ratio of 95 and the ideality factor of 4.92. This work provides an alternative method for the deposition of the NiO film with promising applications in optoelectronic devices

Flame-Made Nb-Doped TiO2 Ethanol and Acetone Sensors

Undoped TiO2 and TiO2 nanoparticles doped with 1–5 at.% Nb were successfully produced in a single step by flame spray pyrolysis (FSP). The phase and crystallite size were analyzed by XRD. The BET surface area (SSABET) of the nanoparticles was measured by nitrogen adsorption. The trend of SSABET on the doping samples increased and the BET equivalent particle diameter (dBET) (rutile) increased with the higher Nb-doping concentrations while dBET (anatase) remained the same. The morphology and accurate size of the primary particles were further investigated by high-resolution transmission electron microscopy (HRTEM). The crystallite sizes of undoped and Nb-doped TiO2 spherical were in the range of 10–20 nm. The sensing films were prepared by spin coating technique. The mixing sample was spin-coated onto the Al2O3 substrates interdigitated with Au electrodes. The gas sensing of acetone (25–400 ppm) was studied at operating temperatures ranging from 300–400 °C in dry air, while the gas sensing of ethanol (50–1,000 ppm) was studied at operating temperatures ranging from 250–400 °C in dry air