5,523 research outputs found
Uncertainty in composite manufacturing and consequences for thermoplastic-thermoset co-curing
This work had four primary objectives:1. Identify the influential parameters during epoxy curing.2. Quantify the effect of measured process variability on curing.3. Propose manufacturing concepts for cure gradients desirable for co-curing.4. Demonstrate the influence of initial degree of cure on thermoplastic-thermoset co-curing.The most influential sources of variability in composite processing were determined by sensitivity analyses using coupled heat transfer and cure kinetics models. The analyses showed, that in the standard aerospace case considered, cure temperature has the most influence and diffusion limiting cure kinetic effects become highly influential post vitrification.To demonstrate the effect a source of process variability can have, calorimeter measurements from industrial scale ovens and autoclaves were used as inputs to a numerical model. It was shown that with the higher heat transfer coefficients in the autoclaves, spatial variability in thermal conditions was less influential. However, this effect was counteracted by the greater variability in the autoclaves, resulting in comparable repeatability between the two vessel types.Combinations of tool material, tool thickness and heat transfer coefficient were explored for maximising part stiffness while retaining bonding surface reactivity for co-curing. A thick, thermally diffusive tool for the bonding surface and a thin, low diffusivity tool elsewhere, in an out-of-autoclave environment was proposed.The effect of initial degree of cure on thermoplastic-thermoset co-curing was investigated at the laminate level. A diffusion model was derived from in-situ measurements of interdiffusion between polyetherimide and a model epoxy system. The model predicted that any increase in initial degree of cure decreased the interaction across the interface. This was supported by mechanical test results and interphase thickness measurements. The results indicated that unlike conventional co-curing, the manufacturing efficiency benefits from increasing the initial degree of cure cannot justify the significant decrease in bond strength
Exact location of dopants below the Si(001):H surface from scanning tunnelling microscopy and density functional theory
Control of dopants in silicon remains the most important approach to
tailoring the properties of electronic materials for integrated circuits, with
Group V impurities the most important n-type dopants. At the same time, silicon
is finding new applications in coherent quantum devices, thanks to the
magnetically quiet environment it provides for the impurity orbitals. The
ionization energies and the shape of the dopant orbitals depend on the surfaces
and interfaces with which they interact. The location of the dopant and local
environment effects will therefore determine the functionality of both future
quantum information processors and next-generation semiconductor devices. Here
we match observed dopant wavefunctions from low-temperature scanning tunnelling
microscopy (STM) to images simulated from first-principles density functional
theory (DFT) calculations. By this combination of experiment and theory we
precisely determine the substitutional sites of neutral As dopants between 5
and 15A below the Si(001):H surface. In the process we gain a full
understanding of the interaction of the donor-electron state with the surface,
and hence of the transition between the bulk dopant (with its delocalised
hydrogenic orbital) and the previously studied dopants in the surface layer.Comment: 12 pages; accepted for publication in Phys. Rev.
Sex ratio distorting microbes exacerbate arthropod extinction risk in variable environments
Maternally-inherited sex ratio distorting microbes (SRDMs) are common among arthropod species. Typically, these microbes cause female-biased sex ratios in host broods, either by; killing male offspring, feminising male offspring, or inducing parthenogenesis. As a result, infected populations can experience drastic ecological and evolutionary change. The mechanism by which SRDMs operate is likely to alter their impact on host evolutionary ecology; despite this, the current literature is heavily biased towards a single mechanism of sex ratio distortion, male-killing. Furthermore, amidst the growing concerns surrounding the loss of arthropod diversity, research into the impact of SRDMs on the viability of arthropod populations is generally lacking. In this study, using a theoretical approach, we model the epidemiology of an understudied mechanism of microbially-induced sex ratio distortionâfeminisationâto ask an understudied questionâhow do SRDMs impact extinction risk in a changing environment? We constructed an individual-based model and measured host population extinction risk under various environmental and epidemiological scenarios. We also used our model to identify the precise mechanism modulating extinction. We find that the presence of feminisers increases host population extinction risk, an effect that is exacerbated in highly variable environments. We also identified transmission rate as the dominant epidemiological trait responsible for driving extinction. Finally, our model shows that sex ratio skew is the mechanism driving extinction. We highlight feminisers and, more broadly, SRDMs as important determinants of the resilience of arthropod populations to environmental change
Sex ratio distorting microbes exacerbate arthropod extinction risk in variable environments
Maternally-inherited sex ratio distorting microbes (SRDMs) are common among arthropod species. Typically, these microbes cause female-biased sex ratios in host broods, either by; killing male offspring, feminising male offspring, or inducing parthenogenesis. As a result, infected populations can experience drastic ecological and evolutionary change. The mechanism by which SRDMs operate is likely to alter their impact on host evolutionary ecology; despite this, the current literature is heavily biased towards a single mechanism of sex ratio distortion, male-killing. Furthermore, amidst the growing concerns surrounding the loss of arthropod diversity, research into the impact of SRDMs on the viability of arthropod populations is generally lacking. In this study, using a theoretical approach, we model the epidemiology of an understudied mechanism of microbially-induced sex ratio distortionâfeminisationâto ask an understudied questionâhow do SRDMs impact extinction risk in a changing environment? We constructed an individual-based model and measured host population extinction risk under various environmental and epidemiological scenarios. We also used our model to identify the precise mechanism modulating extinction. We find that the presence of feminisers increases host population extinction risk, an effect that is exacerbated in highly variable environments. We also identified transmission rate as the dominant epidemiological trait responsible for driving extinction. Finally, our model shows that sex ratio skew is the mechanism driving extinction. We highlight feminisers and, more broadly, SRDMs as important determinants of the resilience of arthropod populations to environmental change
Age related diffusion and tractography changes in typically developing pediatric cervical and thoracic spinal cord
Background and objective: Diffusion tensor imaging (DTI) and diffusion tensor tractography (DTT) are two techniques that can measure white matter integrity of the spinal cord. Recently, DTI indices have been shown to change with age. The purpose of this study is (a) to evaluate the maturational states of the entire pediatric spinal cord using DTI and DTT indices including fractional anisotropy (FA), mean diffusivity (MD), mean length of white matter fiber tracts and tract density and (b) to analyze the DTI and DTT parameters along the entire spinal cord as a function of spinal cord levels and age. Method: A total of 23 typically developing (TD) pediatric subjects ranging in age from 6 to 16 years old (11.94 ± 3.26 (mean ± standard deviation), 13 females and 10 males) were recruited, and scanned using 3.0 T MR scanner. Reduced FOV diffusion tensor images were acquired axially in the same anatomical location prescribed for the T2-weighted images to cover the entire spinal cord (C1-mid L1 levels). To mitigate motion induced artifacts, diffusion directional images were aligned with the reference image (b0) using a rigid body registration algorithm performed by in-house software developed in Matlab (MathWorks, Natick, Massachusetts). Diffusion tensor maps (FA and MD) and streamline deterministic tractography were then generated from the motion corrected DTI dataset. DTI and DTT parameters were calculated by using ROIs drawn to encapsulate the whole cord along the entire spinal cord by an independent board certified neuroradiologist. These indices then were compared between two age groups (age group A = 6â11 years (n = 11) and age group B = 12â16 years (n = 12)) based on similar standards and age definitions used for reporting spinal cord injury in the pediatric population. Standard least squared linear regression based on a restricted maximum likelihood (REML) method was used to evaluate the relationship between age and DTI and DTT parameters. Results: An increase in FA (group A = 0.42 ± 0.097, group B = 0.49 ± 0.116), white matter tract density (group A = 368.01 ± 236.88, group B = 440.13 ± 245.24) and mean length of fiber tracts (group A = 48.16 ± 20.48 mm, group B = 60.28 ± 23.87 mm) and a decrease in MD (group A = 1.06 ± 0.23 Ă 10â3 mm2/s, group B = 0.82 ± 0.24 Ă 10â3 mm2/s) were observed with age along the entire spinal cord. Statistically significant increases have been shown in FA (p = 0.004, R2 = 0.57), tract density (p = 0.0004, R2 = 0.58), mean length of fiber tracts (p \u3c 0.001, R2 = 0.5) and a significant decrease has been shown in MD (p = 0.002, R2 = 0.59) between group A and group B. Also, it has been shown DTI and DTT parameters vary along the spinal cord as a function of intervertebral disk and mid-vertebral body level. Conclusion: This study provides an initial understanding of age related changes of DTI values as well as DTT metrics of the spinal cord. The results show significant differences in DTI and DTT parameters which may result from decreasing water content, myelination of fiber tracts, and the thickening diameter of fiber tracts during the maturation process. Consequently, when quantitative DTI and DTT of the spinal cord is undertaken in the pediatric population an age and level matched normative dataset should be used to accurately interpret the quantitative results. © 201
Sensitivity of evapotranspiration components in remote sensing-based models
Accurately estimating evapotranspiration (ET) at large spatial scales is essential to our understanding of land-atmosphere coupling and the surface balance of water and energy. Comparisons between remote sensing-based ET models are difficult due to diversity in model formulation, parametrization and data requirements. The constituent components of ET have been shown to deviate substantially among models as well as between models and field estimates. This study analyses the sensitivity of three global ET remote sensing models in an attempt to isolate the error associated with forcing uncertainty and reveal the underlying variables driving the model components. We examine the transpiration, soil evaporation, interception and total ET estimates of the Penman-Monteith model from the Moderate Resolution Imaging Spectroradiometer (PM-MOD), the Priestley-Taylor Jet Propulsion Laboratory model (PT-JPL) and the Global Land Evaporation Amsterdam Model (GLEAM) at 42 sites where ET components have been measured using field techniques. We analyse the sensitivity of the models based on the uncertainty of the input variables and as a function of the raw value of the variables themselves. We find that, at 10% added uncertainty levels, the total ET estimates from PT-JPL, PM-MOD and GLEAM are most sensitive to Normalized Difference Vegetation Index (NDVI) (%RMSD = 100.0), relative humidity (%RMSD = 122.3) and net radiation (%RMSD = 7.49), respectively. Consistently, systemic bias introduced by forcing uncertainty in the component estimates is mitigated when components are aggregated to a total ET estimate. These results suggest that slight changes to forcing may result in outsized variation in ET partitioning and relatively smaller changes to the total ET estimates. Our results help to explain why model estimates of total ET perform relatively well despite large inter-model divergence in the individual ET component estimates
Being the âmed regâ: an exploration of junior doctorsâ perceptions of the medical registrar role
The role of the medical registrar is a challenging one and is acknowledged as being a disincentive to a career in medicine for some junior doctors. We set out to build a broader understanding of the role through exploration of Foundation Doctorsâ and Core Medical Traineesâ perceptions of the role. Data, gathered from focus groups, were analysed using a framework approach. Six key themes were identified, which were grouped under the headings âperceptions of the medical registrar roleâ and âtransition into the roleâ. Our work builds on existing literature to inform a deeper understanding of how junior doctors perceive the medical registrar role. In light of our findings we offer suggestions on possible training initiatives to tackle the issues identified. We also highlight positive perceptions of the role and emphasise the key ambassadorial role that current medical registrars have in relation to attracting tomorrowsâ medical registrars to the specialty
Wear and Friction of UHMWPE-on-PEEK OPTIMAâą
PEEK-OPTIMA⹠is being considered as an alternative bearing material to cobalt chrome in the femoral component of total knee replacement to provide a metal-free implant. The aim of this study was to investigate the influence of lubricant temperature (standard rig running and elevated temperature (~36 °C)) on the wear of a UHMWPE-on-PEEK OPTIMA⹠bearing couple using different lubricant protein concentrations (0, 2, 5, 25 and 90% bovine serum) in a simple geometry pin-on-plate configuration. Friction was also investigated under a single temperature condition for different lubricant protein concentrations. The studies were repeated for UHMWPE-on-cobalt chrome in order to compare relationships with temperature (wear only) and lubricant protein concentration (wear and friction).
In low lubricant protein concentrations (†5%) there was no influence of temperature on the wear factors of UHMWPE-on-PEEK. With 25% bovine serum, the wear factor of UHMWPE-on-PEEK reduced by half at elevated temperature. When tested in high protein concentration (90% serum), there was no influence of temperature on the wear factor of UHMWPE-on-PEEK. These temperature dependencies were not the same for UHMWPE-on-cobalt chrome.
For both material combinations, there was a trend of decreasing friction with increasing protein concentration once protein was present in the lubricant.
This study has shown the importance of the selection of appropriate test conditions when investigating the wear and friction of different materials, in order to minimise test artefacts such as polymer transfer, and protein precipitation and deposition
Mitigation Ponds Offer Drought Resiliency for Western Spadefoot (Spea hammondii) Populations
Synergistic effects of habitat loss, drought, and climate change exacerbate amphibian declines. In southern California urbanization continues to convert natural habitat, while prolonged drought reduces surface water availability. Protection of biodiversity may be provided through mitigation; however, the long-term effectiveness of different strategies is often unreported. As a mitigation measure for building a new development within occupied Spea hammondii (western spadefoot) habitat in Orange County, California, artificial breeding pools were constructed at two off-site locations. Spea hammondii tadpoles were translocated from the pools at the development site to two off-site locations in 2005â2006. We conducted surveys a decade later (2016) to determine if S. hammondii were persisting and breeding successfully at either the original development site or the human-made pools at the two mitigation sites. We also verified hydroperiods of any existing pools at all three locations to see if any held water long enough for successful S. hammondii recruitment through metamorphosis. During our study, no pooling water was detected at two of three main sites surveyed, and no S. hammondii were observed at these locations. Twelve of the 14 pools created at only one of the two mitigation sites held water for over 30 d, and we detected successful breeding at seven of these pools. Recruitment in some mitigation ponds indicated that S. hammondii habitat can be created and maintained over 10+ yr, even during the fifth year of a catastrophic drought. Therefore, this may also serve as a conservation strategy to mitigate climate change and habitat loss. During our study, no pooling water was detected at two of three main sites surveyed, and no S. hammondii were observed at these locations. Twelve of the 14 pools created at a third site held water for over 30 days and we detected successful breeding at seven of these pools in 2016. Recruitment in some mitigation ponds indicated that S. hammondii habitat can be created and maintained over 10+ years, even during the fifth year of a catastrophic drought, therefore this may also serve as a management strategy for conservation with regard to climate change and habitat loss
- âŠ