Theoretical Analysis of Continuous Heat Extraction from Absorber of Solar Still for Improving the Productivity

This paper communicates the theoretical analysis of continuous waste heat extraction from the other side of absorber plate. For theoretical analysis two conditions are determined one is the mass of water in the absorber and another one is mass flow rate of water around the absorber plate. Results indicated that the water temperature is reached maximum at 10 kg of mass and 5 kg/hr mass flow of water and the heat extracted from the absorber is higher at optimum mass flow of 5 kg/hr. Also, the higher temperature difference between the water and the collector cover is found during the off-shine period. The maximum achievable hourly productivity of 0.9 and 0.5 kg is found for the solar still with and without circulation respectively. The yield from present model with continuous heat extraction is increased from 3 to 5.5 kg/m2. As the approached method is more new to the society it may be determined by Agouz- Nagarajan- Sathyamurthy (ANS) model

Comparative study of tubular solar stills with phase change material and nano-enhanced phase change mMaterial

This study is intended to investigate and analyze the operational performances of the Conventional Tubular Solar Still (CTSS), Tubular Solar Still with Phase Change Material (TSS-PCM) and Tubular Solar Still with Nano Phase Change Material (TSS-NPCM). Paraffin wax and graphene plusparaffin wax were used in the CTSS to obtain the modified solar still models. The experimental study was carried out in the three stills to observe the operational parameters at a water depth of 1 cm. The experiment revealed that TSS-NPCM showed the best performance and the highest yield in comparison to other stills. The distillate yield from the CTSS, TSS-PCM and TSS-NPCM was noted to be 4.3, 6.0 and 7.9 kg, respectively, the daily energy efficiency of the stills was observed to be 31%, 46% and 59%, respectively, and the daily exergy efficiency of the stills was recorded to be 1.67%, 2.20% and 3.75%, respectively. As the performance of the TSS-NPCM was enhanced, the cost of freshwater yield obtained was also low in contrast to the other two types of stills

Energy, Exergy Analysis, and Optimizations of Collector Cover Thickness of a Solar Still in El Oued Climate, Algeria

Researches in many laboratories on solar still desalination are concerned with increasing efficiency using only solar energy. One of the techniques is the difference in the thickness of the glass cover of the distiller. In order to see the influence of this parameter on efficiency, three similar stills with three different glass coverings were investigated. The flow of heat goes through the cover, and higher glass temperature leads to solar still productivity becoming lower. This paper presents an optimization of glass thickness (Gt) of a conventional solar still (CSS) in El Oued climate, Algeria. Based on the experimental results, the distilled water production rate, energy, and energy efficiency of the CSS have been discussed. The results showed that the suitable Gt of the CSS was 3 mm. The distilled water of around 3.15, 2.02, and 1.13 kg was produced by the CSS at energy efficiency of 30.71, 19.02, and 11.44% with the Gt of 3, 5, and 6 mm, respectively. The daily average exergy efficiency of 2.46, 1.38, and 0.84% was calculated for the CSS at Gt of 3, 5, and 6 mm, respectively

Effect of Design Parameters on Fresh Water Produced from Triangular Basin and Conventional Basin Solar Still

This paper reported the experimental testing of a triangular and conventional basin solar still (TBSS and CBSS). Solar basin and absorber are made of glass and a polyethylene cover, respectively, with an area of 0.25 m2. Square and triangular absorber with the same area of 0.25 m2 with square and triangular glass cover for condensation was fixed. Experimentations were conducted during the month of December 2018, and different natural criteria such as intensity, wind speed, and surrounding ambient temperatures were considered. Also, the modified model was compared to the CBSS on its performance and efficiency characteristics. The experimental results also revealed that the temperature of the water inside the TBSS was higher as compared with that of the CBSS. The daily yield obtained from CBSS and TBSS was found to be 2.7 and 3.2 kg/m2, respectively. Also, the daily efficiency of the TBSS was improved by 11.36% than the CBSS

Experimental performance evaluation of solar still with zig-zag shape air cooled condenser: An energy–exergy analysis approach

In the present experimental effort is made to increase the performance of a solar still (SS) by including a novel design of a zig-zag-shaped air-cooled condenser (ZZACC) and cuprous oxide (CuO) as a nanomaterial. Research work is conducted in the climatic conditions of Gandhinagar, Gujarat, India, from September to November 2020. A comparison was made to assess the performance of a conventional solar still (CSS) and a solar still equipped with a zig-zag shape air-cooled condenser (SSWZZACC) with CuO. The experiments’ findings showed that adding CuO to SSWZZACC increases the distillate production by 46.83% and the daily energy efficiency by 45.98%, respectively, compared to CSS. Also, SSWZZACC demonstrates a better efficiency of exergy and latent heat of vaporization than CSS because CuO causes an increase in the evaporative heat transfer coefficient of water. In life cycle cost analysis study discovered that SSWZZACC has a 27.77% lower cost per litre of water (CPL) than CSS. The obtained maximum energy and exergy efficiency values for CSS and SSWZZACC were 2.36% & 25.75% and 3.9% & 37.59%, respectively. In economic and environmental aspects, it was found that SSWZZACC with CuO showed a cost-effective desalination unit and was highly effective from a carbon credit point of view (CCP) by CO2 mitigation