Investigation of Wireless LAN for IEC 61850 based Smart Distribution Substations

The IEC 61850 standard is receiving acceptance worldwide to deploy Ethernet Local Area Networks (LANs) for electrical substations in a smart grid environment. With the recent growth in wireless communication technologies, wireless Ethernet or Wireless LAN (WLAN), standardized in IEEE 802.11, is gaining interest in the power industry for substation automation applications, especially at the distribution level. Low Voltage (LV) / Medium Voltage (MV) distribution substations have comparatively low time-critical performance requirements. At the same time, expensive but high data-rate fiber-based Ethernet networks may not be a feasible solution for the MV/LV distribution network. Extensive work is carried out to assess wireless LAN technologies for various IEC 61850 based smart distribution substation applications: control and monitoring; automation and metering; and over-current protection. First, the investigation of wireless LANs for various smart distribution substation applications was initiated with radio noise-level measurements in total five (27.6 and 13.8 kV) substations owned by London Hydro and Hydro One in London, ON, Canada. The measured noise level from a spectrum analyzer was modeled using the Probability Distribution Function (PDF) tool in MATLAB, and parameters for these models in the 2.4 GHz band and 5.8 GHz band were obtained. Further, this measured noise models were used to simulate substation environment in OPNET (the industry-trusted communication networking simulation) tool. In addition, the efforts for developing dynamic models of WLAN-enabled IEC 61850 devices were initiated using Proto-C programming in OPNET tool. The IEC 61850 based devices, such as Protection and Control (P&C) Intelligent Electronic Devices (IEDs) and Merging Unit (MU) were developed based on the OSI-7 layer stack proposed in IEC 61850. The performance of various smart distribution substation applications was assessed in terms of average and maximum message transfer delays and throughput. The work was extended by developing hardware prototypes of WLAN enabled IEC 61850 devices in the R&D laboratory at University of Western Ontario, Canada. P&C IED, MU, Processing IED, and Echo IED were developed using industrial embedded computers over the QNX Real Time Operating System (RTOS) platform. The functions were developed using hard real-time multithreads, timers, and so on to communicate IEC 61850 application messages for analyzing WLAN performance in terms of Round Trip Time (RTT) and throughput. The laboratory was set up with WLAN-enabled IEC 61850 devices, a commercially available WLAN Access Point (AP), noise sources, and spectrum and network analyzers. Performance of various smart distribution substation applications is examined within the developed laboratory. Finally, the performance evaluation was carried out in real-world field testing at 13.8 and 27.6 kV distribution substations, by installing the devices in substation control room and switchyard. The RTT of IEC 61850 based messages and operating time of the overcurrent protection using WLAN based communication network were evaluated in the harsh environment of actual distribution substations. The important findings from the exhaustive investigation were discussed throughout this work

Development of the future generation of smart high voltage connectors and related components for substations, with energy autonomy and wireless data transmission capability

The increased dependency on electricity of modern society, makes reliability of power transmission systems a key point. This goal can be achieved by continuously monitoring power grid parameters, so possible failure modes can be predicted beforehand. It can be done using existing Information and Communication Technologies (ICT) and Internet of Things (10T) technologies that include instrumentation and wireless communication systems, thus forming a wireless sensor network (WSN). Electrical connectors are among the most critical parts of any electrical system and hence, they can act as nodes of such WSN. Therefore, the fundamental objective of this thesis is the design, development and experimental validation of a self-powered IOT solution for real-time monitoring of the health status of a high-voltage substation connector and related components of the electrical substation. This new family of power connectors is called SmartConnector and incorporates a thermal energy harvesting system powering a microcontroller that controls a transmitter and several electronic sensors to measure the temperature, current and the electrical contact resistance (ECR) of the connector. These measurements are sent remotely via a Bluetooth 5 wireless communication module to a local gateway, which further transfers the measured data to a database server for storage as well as further analysis and visualization. By this way, after suitable data processing, the health status of the connector can be available in real-time, allowing different appealing functions, such as assessing the correct installation of the connector, the current health status or its remaining useful life (RUL) in real-time. The same principal can also be used for other components of substation like spacers, insulators, conductors, etc. Hence, to prove universality of this novel approach, a similar strategy is applied to a spacer which is capable of measuring uneven current distribution in three closely placed conductors. This novel IOT device is called as SmartSpacer. Care has to be taken that this technical and scientific development has to be compatible with existing substation bus bars and conductors, and especially to be compatible with the high operating voltages, i.e., from tens to hundreds of kilo-Volts (kV), and with currents in the order of some kilo-pm peres (kA). Although some electrical utilities and manufacturers have progressed in the development of such technologies, including smart meters and smart sensors, electrical device manufacturers such as of substation connectors manufacturers have not yet undertaken the technological advancement required for the development of such a new family of smart components involved in power transmission, which are designed to meet the future needs.La mayor dependencia de la electricidad de la sociedad moderna hace que la fiabilidad de los sistemas de transmisión de energía sea un punto clave. Este objetivo se puede lograr mediante la supervisión continua de los parámetros de la red eléctrica, por lo que los posibles modos de fallo se pueden predecir de antemano. Se puede hacer utilizando las tecnologías existentes de Tecnologías de la Información y la Comunicación (1CT) e Internet de las cosas (lo T) que incluyen sistemas de instrumentación y comunicación inalámbrica, formando así una red de sensores inalámbricos (WSN). Los conectores eléctricos se encuentran entre las partes más críticas de cualquier sistema eléctrico y, por lo tanto, pueden actuar como nodos de dicho VVSN. Por lo tanto, el objetivo fundamental de esta tesis es el diseño, desarrollo y validación experimental de una solución IOT autoalimentada para la supervisión en tiempo real del estado de salud de un conector de subestación de alta tensión y componentes relacionados de la subestación eléctrica. Esta nueva familia de conectores de alimentación se llama SmartConnector e incorpora un sistema de recolección de energía térmica que alimenta un microcontrolador que controla un transmisor y varios sensores electrónicos para medir la temperatura, la corriente y la resistencia del contacto eléctrico (ECR) del conector. Esta nueva familia de conectores de alimentación se llama SmartConnector e incorpora un sistema de recolección de energía térmica que alimenta un microcontrolador que controla un transmisor y varios sensores electrónicos para medir la temperatura, la corriente y la resistencia al contacto eléctrico (ECR) del conector. De esta manera, después del procesamiento de datos adecuado, el estado de salud del conector puede estar disponible en tiempo real, permitiendo diferentes funciones atractivas, como evaluar la correcta instalación del conector, el estado de salud actual o su vida útil restante (RUL) en tiempo real. El mismo principio también se puede utilizar para otros componentes de la subestación como espaciadores, aislantes, conductores, etc. Por lo tanto, para demostrar la universalidad de este enfoque novedoso, se aplica una estrategia similar a un espaciador, que es capaz de medir la distribución de corriente desigual en tres conductores estrechamente situados. Hay que tener cuidado de que este desarrollo técnico y científico tenga que sea compatible con las barras y "busbars" de subestación existentes, y sobre todo para ser compatible con las altas tensiones de funcionamiento, es decir, de decenas a cientos de kilovoltios (kV), y con corrientes en el orden de algunos kilo-Amperes (kA). Aunque algunas empresas eléctricas y fabricantes han progresado en el desarrollo de este tipo de tecnologías, incluidos medidores inteligentes y sensores inteligentes, los fabricantes de dispositivos eléctricos, como los fabricantes de conectores de subestación, aún no han emprendido el avance tecnológico necesario para el desarrollo de una nueva familia de componentes intel

A wireless 802.11 condition monitoring sensor for electrical substation environments

The work reported in this thesis is concerned with the design, development and testing of a wireless 802.11 condition monitoring sensor for an electrical substation environments. The work includes a comprehensive literature review and the design and development of a novel continuous wireless data acquisition sensor. Laboratory and field tests were performed to evaluate the data acquisition performance of the developed wireless sensor. The sensor‟s wireless immunity to interference performance was also evaluated in laboratory and field tests. The literature survey reviews current condition monitoring practices in electrical substation environments with a focus on monitoring high voltage insulators and substation earth impedance. The data acquisition performance of the wireless sensor was tested in a laboratory using two artificially polluted insulators, in a fog chamber that applied clean fog. Analysis of the test results were found to be in good agreement with those recorded directly through a data acquisition card and transmitted via coaxial cable. The wireless impedance measurement of a 275kV transmission earth tower base field test was also performed and was found to be in agreement with previous published results from standard earth measurements. The sensor‟s wireless interference performance was evaluated at a field test site when no high voltage experiments were taking place. The sensors wireless interference performance was then tested in a laboratory environment before and during high voltage tests taking place. The results of these tests were compared to each other and to published results. These tests demonstrate the suitability of the sensor‟s design and its immunity to interference. The experimental work conducted using the developed wireless sensor has led to an understanding that continuous wireless data acquisition is possible in high voltage environments. However, novel condition monitoring systems that make use of such wireless sensors, have to take into account data losses and delays adequately. Furthermore, a solar power source was designed and constructed to be used for outdoor substation applications and the solar battery charging performance of the wireless sensor was tested in a solar laboratory.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

A wireless 802.11 condition monitoring sensor for electrical substation environments

The work reported in this thesis is concerned with the design, development and testing of a wireless 802.11 condition monitoring sensor for an electrical substation environments. The work includes a comprehensive literature review and the design and development of a novel continuous wireless data acquisition sensor. Laboratory and field tests were performed to evaluate the data acquisition performance of the developed wireless sensor. The sensor‟s wireless immunity to interference performance was also evaluated in laboratory and field tests. The literature survey reviews current condition monitoring practices in electrical substation environments with a focus on monitoring high voltage insulators and substation earth impedance. The data acquisition performance of the wireless sensor was tested in a laboratory using two artificially polluted insulators, in a fog chamber that applied clean fog. Analysis of the test results were found to be in good agreement with those recorded directly through a data acquisition card and transmitted via coaxial cable. The wireless impedance measurement of a 275kV transmission earth tower base field test was also performed and was found to be in agreement with previous published results from standard earth measurements. The sensor‟s wireless interference performance was evaluated at a field test site when no high voltage experiments were taking place. The sensors wireless interference performance was then tested in a laboratory environment before and during high voltage tests taking place. The results of these tests were compared to each other and to published results. These tests demonstrate the suitability of the sensor‟s design and its immunity to interference. The experimental work conducted using the developed wireless sensor has led to an understanding that continuous wireless data acquisition is possible in high voltage environments. However, novel condition monitoring systems that make use of such wireless sensors, have to take into account data losses and delays adequately. Furthermore, a solar power source was designed and constructed to be used for outdoor substation applications and the solar battery charging performance of the wireless sensor was tested in a solar laboratory

Caractérisation des milieux hautes tensions en vue d'adapter un réseau sans fil de capteurs

Les postes de transports d'énergie d'Hydro-Québec sont le siège d'interférences électromagnétiques causées par les hautes tensions véhiculées et par le fonctionnement de l'équipement présent sur le site. Les études de cet environnement ont révélé que le bruit électromagnétique varie d'une puissance allant de -176 dBm à 40 dBm pour une gamme de 10 MHz à 10 GHz. Ne pouvant tirer des câbles réseaux sur une aire de 1 Km2, un réseau de capteurs sans fil est de loin la meilleure solution pour contrôler les équipements présents depuis l'extérieur. Il faut donc rassembler les différentes technologies du sans fil (Wi-Fi, Wimax, LTE ... ) afin de mettre en réseau les capteurs de ces équipements, tout en prenant en compte la localisation du bruit et ses caractéristiques (fréquence, gain) pour la sélection du matériel de communication et son emplacement. Ce mémoire vise à caractériser l'environnement électromagnétique des postes de transport d'énergie en recensant les bruits déjà mesurés et en proposant une méthode de capture et d'analyse du bruit impulsionnel

City-Friendly Smart Network Technologies and Infrastructures: The Spanish Experience

Efficient, resilient, and sustainable electricity delivery is a key cornerstone in increasingly large and complex urban environments, where citizens expect to keep or rise their living standards. In this context, cost-effective and ubiquitous digital technologies are driving the transformation of existing electrical infrastructures into truly smart systems capable of better providing the services a low-carbon society is demanding. The goal of this paper is twofold: 1) to review the dramatically evolving landscape of power systems, from the old framework based on centralized generation and control, aimed at serving inelastic customers through alternating current (ac) transmission networks and one-way distribution feeders, to a new paradigm centered mainly around two main axes: renewable generation, both centralized and distributed, and active customers (prosumers), interacting with each other through hybrid ac/dc smart grids; 2) to illustrate, through featured success stories, how several smart grid concepts and technologies have been put into practice in Spain over the last few years to optimize the performance of urban electrical assets

Load Monitoring CEC/LMTF Load Research Program

This white paper addresses the needs, options, current practices of load monitoring. Recommendations on load monitoring applications and future directions are also presented