Digital and analog TFET circuits: Design and benchmark

In this work, we investigate by means of simulations the performance of basic digital, analog, and mixed-signal circuits employing tunnel-FETs (TFETs). The analysis reviews and complements our previous papers on these topics. By considering the same devices for all the analysis, we are able to draw consistent conclusions for a wide variety of circuits. A virtual complementary TFET technology consisting of III-V heterojunction nanowires is considered. Technology Computer Aided Design (TCAD) models are calibrated against the results of advanced full-quantum simulation tools and then used to generate look-up-tables suited for circuit simulations. The virtual complementary TFET technology is benchmarked against predictive technology models (PTM) of complementary silicon FinFETs for the 10 nm node over a wide range of supply voltages (VDD) in the sub-threshold voltage domain considering the same footprint between the vertical TFETs and the lateral FinFETs and the same static power. In spite of the asymmetry between p- and n-type transistors, the results show clear advantages of TFET technology over FinFET for VDDlower than 0.4 V. Moreover, we highlight how differences in the I-V characteristics of FinFETs and TFETs suggest to adapt the circuit topologies used to implement basic digital and analog blocks with respect to the most common CMOS solutions

Digital and analog TFET circuits: Design and benchmark

In this work, we investigate by means of simulations the performance of basic digital, analog, and mixed-signal circuits employing tunnel-FETs (TFETs). The analysis reviews and complements our previous papers on these topics. By considering the same devices for all the analysis, we are able to draw consistent conclusions for a wide variety of circuits. A virtual complementary TFET technology consisting of III-V heterojunction nanowires is considered. Technology Computer Aided Design (TCAD) models are calibrated against the results of advanced full-quantum simulation tools and then used to generate look-up-tables suited for circuit simulations. The virtual complementary TFET technology is benchmarked against predictive technology models (PTM) of complementary silicon FinFETs for the 10 nm node over a wide range of supply voltages (VDD) in the sub-threshold voltage domain considering the same footprint between the vertical TFETs and the lateral FinFETs and the same static power. In spite of the asymmetry between p- and n-type transistors, the results show clear advantages of TFET technology over FinFET for VDDlower than 0.4 V. Moreover, we highlight how differences in the I-V characteristics of FinFETs and TFETs suggest to adapt the circuit topologies used to implement basic digital and analog blocks with respect to the most common CMOS solutions

Tunnel Field-Effect Transistor: Impact of the Asymmetric and Symmetric Ambipolarity on Fault and Performance in Digital Circuits

Tunnel Field-Effect Transistors (TFETs) have been considered one of the most promising technologies to complement or replace CMOS for ultra-low-power applications, thanks to their subthreshold slope below the well-known limit of 60 mV/dec at room temperature holding for the MOSFET technologies. Nevertheless, TFET technology still suffers of ambipolar conduction, limiting its applicability in digital systems. In this work, we analyze through SPICE simulations, the impact of the symmetric and asymmetric ambipolarity in failure and power consumption for TFET-based complementary logic circuits. Our results clarify the circuit-level effects induced by the ambipolarity feature, demonstrating that it affects the correct functioning of logic gates and strongly impacts power consumption. We believe that our outcomes motivate further research towards technological solutions for ambipolarity suppression in TFET technology for near-future ultra-low-power application

III-V and 2D Devices: from MOSFETs to Steep-Slope Transistors

With silicon CMOS technology approaching the scaling limit, alternating channel materials and novel device structures have been extensively studied and attracted a lot of attention in solid-state device research. In this dissertation, solid-state electron devices for post-Si CMOS applications are explored including both new materials such as III-V and 2D materials and new device structures such as tunneling field-effect transistors and negative capacitance field-effect transistors. Multiple critical challenges in applying such new materials and new device structures are addressed and the key achievements in this dissertation are summarized as follows: 1) Development of fabrication process technology for ultra-scaled planar and 3D InGaAs MOSFETs. 2) Interface passivation by forming gas anneal on InGaAs gate-all-around MOSFETs. 3) Characterization methods for ultra-scaled MOSFETs, including a correction to subthreshold method and low frequency noise characterization in short channel devices. 4) Development of short channel InGaAs planar and 3D gate-allaround tunneling field-effect transistors. 5) Negative capacitance field-effect transistors with hysteresis-free and bi-directional sub-thermionic subthreshold slope and the integration with various channel materials such as InGaAs and MoS2

Devenlopment of Compact Small Signal Quasi Static Models for Multiple Gate Mosfets

En esta tesis hemos desarrollado los modelos compactos explícitos de carga y de capacitancia adaptados para los dispositivos dopados y no dopados de canal largo (DG MOSFETs dopados, DG MOSFETs no dopados, UTB MOSFETs no dopados y SGT no dopados) de un modelo unificado del control de carga derivado de la ecuación de Poisson. El esquema de modelado es similar en todos estos dispositivos y se adapta a cada geometría. Los modelos de la C.C. y de la carga son completamente compatibles. Las expresiones de la capacitancia se derivan del modelo de la carga. La corriente, la carga total y las capacitancias se escriben en términos de las densidades móviles de la carga en los extremos de fuente y drenador del canal. Las expresiones explícitas e infinitamente continuas se utilizan para las densidades móviles de la carga en la fuente y drenador. Las capacitancias modeladas demuestran el acuerdo excelente con las simulaciones numéricas 2D y 3D (SGT), en todos los regímenes de funcionamiento. Por lo tanto, el modelo es muy prometedor para ser utilizado en simuladores del circuito. Desafortunadamente, no mucho trabajo se ha dedicado a este dominio de modelado. Las cargas analíticas y las capacitancias, asociadas a cada terminal se prefieren en la simulación de circuito. Con respecto al SGT MOSFET, nuestro grupo fue el primero en desarrollar y publicar un modelo de las cargas y de las capacitancias intrínsecas, que es también analítico y explícito. La tesis es organizada como sigue: el capítulo (1) presenta el estado del arte, capítulo (2) el modelado compacto de los cuatro dispositivos: DG MOSFETs dopados, DG MOSFETs no dopados, UTB MOSFETs no dopados y SGT no dopados; en el capítulo (3) estudiamos las capacitancias de fricción en MuGFETs. Finalmente el capítulo (4) resuma el trabajo hecho y los futuros objetivos que necesitan ser estudiados. Debido a la limitación de los dispositivos optimizados disponibles para el análisis, la simulación numérica fue utilizada como la herramienta principal del análisis. Sin embargo, cuando estaban disponibles, medidas experimentales fueron utilizadas para validar nuestros resultados. Por ejemplo, en la sección 2A, en el caso de DG MOSFETs altamente dopados podríamos comparar nuestros resultados con datos experimentales de FinFETs modelados como DG MOSFETs. La ventaja principal de este trabajo es el carácter analítico y explícito del modelo de la carga y de la capacitancia que las hace fácil de implementar en simuladores de circuitos. El modelo presenta los resultados casi perfectos para diversos casos del dopaje y para diversas estructuras no clásicas del MOSFET (los DG MOSFETs, los UTB MOSFETs y los SGTs). La variedad de las estructuras del MOSFET en las cuales se ha incluido nuestro esquema de modelado y los resultados obtenidos, demuestran su validez absoluta. En el capítulo 3, investigamos la influencia de los parámetros geométricos en el funcionamiento en RF de los MuGFETs. Demostramos el impacto de parámetros geométricos importantes tales como el grosor de la fuente y del drenador o, el espaciamiento de las fins, la anchura del espaciador, etc. en el componente parásito de la capacitancia de fricción de los transistores de la múltiple-puerta (MuGFET). Los resultados destacan la ventaja de disminuir el espaciamiento entre las fins para MuGFETs y la compensación entre la reducción de las resistencias parásitas de fuente y drenador y el aumento de capacitancias de fricción cuando se introduce la tecnología del crecimiento selectivo epitaxial (SEG). La meta de nuestro estudio y trabajo es el uso de nuestros modelos en simuladores de circuitos. El grupo de profesor Aranda, de la Universidad de Granada ha puesto el modelo actual de SGT en ejecución en el simulador Agilent ADS y buenos resultados fueron obtenidos.In this thesis we have developed explicit compact charge and capacitance models adapted for doped and undoped long-channel devices (doped Double-Gate (DG) MOSFETs, undoped DG MOSFETs, undoped Ultra-Thin-Body (UTB) MOSFETs and undoped Surrounding Gate Transistor (SGT)) from a unified charge control model derived from Poisson's equation. The modelling scheme is similar in all these devices and is adapted to each geometry. The dc and charge models are fully compatible. The capacitance expressions are derived from the charge model. The current, total charges and capacitances are written in terms of the mobile charge sheet densities at the source and drain ends of the channel. Explicit and infinitely continuous expressions are used for the mobile charge sheet densities at source and drain. As a result, all small signal parameters will have an infinite order of continuity. The modeled capacitances show excellent agreement with the 2D and 3D (SGT) numerical simulations, in all operating regimes. Therefore, the model is very promising for being used in circuit simulators. Unfortunately, not so much work has been dedicated to this modelling domain. Analytical charges and capacitances, associated with each terminal are preferred in circuit simulation. Regarding the surrounding-gate MOSFET, our group was the first to develop and publish a model of the charges and intrinsic capacitances, which is also analytic and explicit. The thesis is organized as follows: Chapter (1) presents the state of the art, Chapter (2) the compact modeling of the four devices: doped DG MOSFETs, undoped DG MOSFETs, undoped UTB MOSFETs and undoped SGT; in Chapter (3) we study the fringing capacitances in MuGFETs. Finally Chapter (4) summarizes the work done and the future points that need to be studied. Due to the limitation of available optimized devices for analysis, numerical simulation was used as the main analysis tool. However, when available, measurements were used to validate our results. The experimental part was realised at the Microelectronics Laboratory, Université Catholique de Louvain, Louvain-la Neuve, Belgium. For example, in section 2A, in the case of highly-doped DG MOSFETs we could compare our results with experimental data from FinFETs modeled as DG MOSFETs. The main advantage of this work is the analytical and explicit character of the charge and capacitance model that makes it easy to implement in circuit simulators. The model presents almost perfect results for different cases of doping (doped/undoped devices) and for different non classical MOSFET structures (DG MOSFET, UTB MOSFETs and SGT). The variety of the MOSFET structures in which our modeling scheme has been included and the obtained results, demonstrate its absolute validity. In chapter 3, we investigate the influence of geometrical parameters on the RF performance in MuGFETs. We show the impact of important geometrical parameters such as source and drain thickness, fin spacing, spacer width, etc. on the parasitic fringing capacitance component of multiple-gate field-effect transistors (MuGFET). Results highlight the advantage of diminishing the spacing between fins for MuGFETs and the trade-off between the reduction of parasitic source and drain resistances and the increase of fringing capacitances when Selective Epitaxial Growth (SEG) technology is introduced. The goal of our study and work is the usage of our models in circuit simulators. This part, of implementing and testing our models of these multi gate MOSFET devices in circuit simulators has already begun. The group of Professor Aranda, from the University of Granada has implemented the SGT current model in the circuit simulator Agilent ADS and good results were obtained

A hierarchical optimization engine for nanoelectronic systems using emerging device and interconnect technologies

A fast and efficient hierarchical optimization engine was developed to benchmark and optimize various emerging device and interconnect technologies and system-level innovations at the early design stage. As the semiconductor industry approaches sub-20nm technology nodes, both devices and interconnects are facing severe physical challenges. Many novel device and interconnect concepts and system integration techniques are proposed in the past decade to reinforce or even replace the conventional Si CMOS technology and Cu interconnects. To efficiently benchmark and optimize these emerging technologies, a validated system-level design methodology is developed based on the compact models from all hierarchies, starting from the bottom material-level, to the device- and interconnect-level, and to the top system-level models. Multiple design parameters across all hierarchies are co-optimized simultaneously to maximize the overall chip throughput instead of just the intrinsic delay or energy dissipation of the device or interconnect itself. This optimization is performed under various constraints such as the power dissipation, maximum temperature, die size area, power delivery noise, and yield. For the device benchmarking, novel graphen PN junction devices and InAs nanowire FETs are investigated for both high-performance and low-power applications. For the interconnect benchmarking, a novel local interconnect structure and hybrid Al-Cu interconnect architecture are proposed, and emerging multi-layer graphene interconnects are also investigated, and compared with the conventional Cu interconnects. For the system-level analyses, the benefits of the systems implemented with 3D integration and heterogeneous integration are analyzed. In addition, the impact of the power delivery noise and process variation for both devices and interconnects are quantified on the overall chip throughput.Ph.D

Multiple-Independent-Gate Field-Effect Transistors for High Computational Density and Low Power Consumption

Transistors are the fundamental elements in Integrated Circuits (IC). The development of transistors significantly improves the circuit performance. Numerous technology innovations have been adopted to maintain the continuous scaling down of transistors. With all these innovations and efforts, the transistor size is approaching the natural limitations of materials in the near future. The circuits are expected to compute in a more efficient way. From this perspective, new device concepts are desirable to exploit additional functionality. On the other hand, with the continuously increased device density on the chips, reducing the power consumption has become a key concern in IC design. To overcome the limitations of Complementary Metal-Oxide-Semiconductor (CMOS) technology in computing efficiency and power reduction, this thesis introduces the multiple- independent-gate Field-Effect Transistors (FETs) with silicon nanowires and FinFET structures. The device not only has the capability of polarity control, but also provides dual-threshold- voltage and steep-subthreshold-slope operations for power reduction in circuit design. By independently modulating the Schottky junctions between metallic source/drain and semiconductor channel, the dual-threshold-voltage characteristics with controllable polarity are achieved in a single device. This property is demonstrated in both experiments and simulations. Thanks to the compact implementation of logic functions, circuit-level benchmarking shows promising performance with a configurable dual-threshold-voltage physical design, which is suitable for low-power applications. This thesis also experimentally demonstrates the steep-subthreshold-slope operation in the multiple-independent-gate FETs. Based on a positive feedback induced by weak impact ionization, the measured characteristics of the device achieve a steep subthreshold slope of 6 mV/dec over 5 decades of current. High Ion/Ioff ratio and low leakage current are also simultaneously obtained with a good reliability. Based on a physical analysis of the device operation, feasible improvements are suggested to further enhance the performance. A physics-based surface potential and drain current model is also derived for the polarity-controllable Silicon Nanowire FETs (SiNWFETs). By solving the carrier transport at Schottky junctions and in the channel, the core model captures the operation with independent gate control. It can serve as the core framework for developing a complete compact model by integrating advanced physical effects. To summarize, multiple-independent-gate SiNWFETs and FinFETs are extensively studied in terms of fabrication, modeling, and simulation. The proposed device concept expands the family of polarity-controllable FETs. In addition to the enhanced logic functionality, the polarity-controllable SiNWFETs and FinFETs with the dual-threshold-voltage and steep-subthreshold-slope operation can be promising candidates for future IC design towards low-power applications

Polarity Control at Runtime:from Circuit Concept to Device Fabrication

Semiconductor device research for digital circuit design is currently facing increasing challenges to enhance miniaturization and performance. A huge economic push and the interest in novel applications are stimulating the development of new pathways to overcome physical limitations affecting conventional CMOS technology. Here, we propose a novel Schottky barrier device concept based on electrostatic polarity control. Specifically, this device can behave as p- or n-type by simply changing an electric input bias. This device combines More-than-Moore and Beyond CMOS elements to create an efficient technology with a viable path to Very Large Scale Integration (VLSI). This thesis proposes a device/circuit/architecture co-optimization methodology, where aspects of device technology to logic circuit and system design are considered. At device level, a full CMOS compatible fabrication process is presented. In particular, devices are demonstrated using vertically stacked, top-down fabricated silicon nanowires with gate-all-around electrode geometry. Source and drain contacts are implemented using nickel silicide to provide quasi-symmetric conduction of either electrons or holes, depending on the mode of operation. Electrical measurements confirm excellent performance, showing Ion/Ioff > 10^7 and subthreshold slopes approaching the thermal limit, SS ~ 60mV/dec (~ 63mV/dec) for n(p)-type operation in the same physical device. Moreover, the shown devices behave as p-type for a polarization bias (polarity gate voltage, Vpg) of 0V, and n-type for a Vpg = 1V, confirming their compatibility with multi-level static logic circuit design. At logic gate level, two- and four-transistor logic gates are fabricated and tested. In particular, the first fully functional, two-transistor XOR logic gate is demonstrated through electrical characterization, confirming that polarity control can enable more compact logic gate design with respect to conventional CMOS. Furthermore, we show for the first time fabricated four- transistors logic gates that can be reconfigured as NAND or XOR only depending on their external connectivity. In this case, logic gates with full swing output range are experimentally demonstrated. Finally, single device and mixed-mode TCAD simulation results show that lower Vth and more optimized polarization ranges can be expected in scaled devices implementing strain or high-k technologies. At circuit and system level, a full semi-custom logic circuit design tool flow was defined and configured. Using this flow, novel logic libraries based on standard cells or regular gate fabrics were compared with standard CMOS. In this respect, results were shown in comparison to CMOS, including a 40% normalized area-delay product reduction for the analyzed standard cell libraries, and improvements of over 2× in terms of normalized delay for regular Controlled Polarity (CP)-based cells in the context of Structured ASICs. These results, in turn, confirm the interest in further developing and optimizing CP devices, as promising candidates for future digital circuit technology

Degradation Models and Optimizations for CMOS Circuits

Die Gewährleistung der Zuverlässigkeit von CMOS-Schaltungen ist derzeit eines der größten Herausforderungen beim Chip- und Schaltungsentwurf. Mit dem Ende der Dennard-Skalierung erhöht jede neue Generation der Halbleitertechnologie die elektrischen Felder innerhalb der Transistoren. Dieses stärkere elektrische Feld stimuliert die Degradationsphänomene (Alterung der Transistoren, Selbsterhitzung, Rauschen, usw.), was zu einer immer stärkeren Degradation (Verschlechterung) der Transistoren führt. Daher erleiden die Transistoren in jeder neuen Technologiegeneration immer stärkere Verschlechterungen ihrer elektrischen Parameter. Um die Funktionalität und Zuverlässigkeit der Schaltung zu wahren, wird es daher unerlässlich, die Auswirkungen der geschwächten Transistoren auf die Schaltung präzise zu bestimmen. Die beiden wichtigsten Auswirkungen der Verschlechterungen sind ein verlangsamtes Schalten, sowie eine erhöhte Leistungsaufnahme der Schaltung. Bleiben diese Auswirkungen unberücksichtigt, kann die verlangsamte Schaltgeschwindigkeit zu Timing-Verletzungen führen (d.h. die Schaltung kann die Berechnung nicht rechtzeitig vor Beginn der nächsten Operation abschließen) und die Funktionalität der Schaltung beeinträchtigen (fehlerhafte Ausgabe, verfälschte Daten, usw.). Um diesen Verschlechterungen der Transistorparameter im Laufe der Zeit Rechnung zu tragen, werden Sicherheitstoleranzen eingeführt. So wird beispielsweise die Taktperiode der Schaltung künstlich verlängert, um ein langsameres Schaltverhalten zu tolerieren und somit Fehler zu vermeiden. Dies geht jedoch auf Kosten der Performanz, da eine längere Taktperiode eine niedrigere Taktfrequenz bedeutet. Die Ermittlung der richtigen Sicherheitstoleranz ist entscheidend. Wird die Sicherheitstoleranz zu klein bestimmt, führt dies in der Schaltung zu Fehlern, eine zu große Toleranz führt zu unnötigen Performanzseinbußen. Derzeit verlässt sich die Industrie bei der Zuverlässigkeitsbestimmung auf den schlimmstmöglichen Fall (maximal gealterter Schaltkreis, maximale Betriebstemperatur bei minimaler Spannung, ungünstigste Fertigung, etc.). Diese Annahme des schlimmsten Falls garantiert, dass der Chip (oder integrierte Schaltung) unter allen auftretenden Betriebsbedingungen funktionsfähig bleibt. Darüber hinaus ermöglicht die Betrachtung des schlimmsten Falles viele Vereinfachungen. Zum Beispiel muss die eigentliche Betriebstemperatur nicht bestimmt werden, sondern es kann einfach die schlimmstmögliche (sehr hohe) Betriebstemperatur angenommen werden. Leider lässt sich diese etablierte Praxis der Berücksichtigung des schlimmsten Falls (experimentell oder simulationsbasiert) nicht mehr aufrechterhalten. Diese Berücksichtigung bedingt solch harsche Betriebsbedingungen (maximale Temperatur, etc.) und Anforderungen (z.B. 25 Jahre Betrieb), dass die Transistoren unter den immer stärkeren elektrischen Felder enorme Verschlechterungen erleiden. Denn durch die Kombination an hoher Temperatur, Spannung und den steigenden elektrischen Feldern bei jeder Generation, nehmen die Degradationphänomene stetig zu. Das bedeutet, dass die unter dem schlimmsten Fall bestimmte Sicherheitstoleranz enorm pessimistisch ist und somit deutlich zu hoch ausfällt. Dieses Maß an Pessimismus führt zu erheblichen Performanzseinbußen, die unnötig und demnach vermeidbar sind. Während beispielsweise militärische Schaltungen 25 Jahre lang unter harschen Bedingungen arbeiten müssen, wird Unterhaltungselektronik bei niedrigeren Temperaturen betrieben und muss ihre Funktionalität nur für die Dauer der zweijährigen Garantie aufrechterhalten. Für letzteres können die Sicherheitstoleranzen also deutlich kleiner ausfallen, um die Performanz deutlich zu erhöhen, die zuvor im Namen der Zuverlässigkeit aufgegeben wurde. Diese Arbeit zielt darauf ab, maßgeschneiderte Sicherheitstoleranzen für die einzelnen Anwendungsszenarien einer Schaltung bereitzustellen. Für fordernde Umgebungen wie Weltraumanwendungen (wo eine Reparatur unmöglich ist) ist weiterhin der schlimmstmögliche Fall relevant. In den meisten Anwendungen, herrschen weniger harsche Betriebssbedingungen (z.B. sorgen Kühlsysteme für niedrigere Temperaturen). Hier können Sicherheitstoleranzen maßgeschneidert und anwendungsspezifisch bestimmt werden, sodass Verschlechterungen exakt toleriert werden können und somit die Zuverlässigkeit zu minimalen Kosten (Performanz, etc.) gewahrt wird. Leider sind die derzeitigen Standardentwurfswerkzeuge für diese anwendungsspezifische Bestimmung der Sicherheitstoleranz nicht gut gerüstet. Diese Arbeit zielt darauf ab, Standardentwurfswerkzeuge in die Lage zu versetzen, diesen Bedarf an Zuverlässigkeitsbestimmungen für beliebige Schaltungen unter beliebigen Betriebsbedingungen zu erfüllen. Zu diesem Zweck stellen wir unsere Forschungsbeiträge als vier Schritte auf dem Weg zu anwendungsspezifischen Sicherheitstoleranzen vor: Schritt 1 verbessert die Modellierung der Degradationsphänomene (Transistor-Alterung, -Selbsterhitzung, -Rauschen, etc.). Das Ziel von Schritt 1 ist es, ein umfassendes, einheitliches Modell für die Degradationsphänomene zu erstellen. Durch die Verwendung von materialwissenschaftlichen Defektmodellierungen werden die zugrundeliegenden physikalischen Prozesse der Degradationsphänomena modelliert, um ihre Wechselwirkungen zu berücksichtigen (z.B. Phänomen A kann Phänomen B beschleunigen) und ein einheitliches Modell für die simultane Modellierung verschiedener Phänomene zu erzeugen. Weiterhin werden die jüngst entdeckten Phänomene ebenfalls modelliert und berücksichtigt. In Summe, erlaubt dies eine genaue Degradationsmodellierung von Transistoren unter gleichzeitiger Berücksichtigung aller essenziellen Phänomene. Schritt 2 beschleunigt diese Degradationsmodelle von mehreren Minuten pro Transistor (Modelle der Physiker zielen auf Genauigkeit statt Performanz) auf wenige Millisekunden pro Transistor. Die Forschungsbeiträge dieser Dissertation beschleunigen die Modelle um ein Vielfaches, indem sie zuerst die Berechnungen so weit wie möglich vereinfachen (z.B. sind nur die Spitzenwerte der Degradation erforderlich und nicht alle Werte über einem zeitlichen Verlauf) und anschließend die Parallelität heutiger Computerhardware nutzen. Beide Ansätze erhöhen die Auswertungsgeschwindigkeit, ohne die Genauigkeit der Berechnung zu beeinflussen. In Schritt 3 werden diese beschleunigte Degradationsmodelle in die Standardwerkzeuge integriert. Die Standardwerkzeuge berücksichtigen derzeit nur die bestmöglichen, typischen und schlechtestmöglichen Standardzellen (digital) oder Transistoren (analog). Diese drei Typen von Zellen/Transistoren werden von der Foundry (Halbleiterhersteller) aufwendig experimentell bestimmt. Da nur diese drei Typen bestimmt werden, nehmen die Werkzeuge keine Zuverlässigkeitsbestimmung für eine spezifische Anwendung (Temperatur, Spannung, Aktivität) vor. Simulationen mit Degradationsmodellen ermöglichen eine Bestimmung für spezifische Anwendungen, jedoch muss diese Fähigkeit erst integriert werden. Diese Integration ist eines der Beiträge dieser Dissertation. Schritt 4 beschleunigt die Standardwerkzeuge. Digitale Schaltungsentwürfe, die nicht auf Standardzellen basieren, sowie komplexe analoge Schaltungen können derzeit nicht mit analogen Schaltungssimulatoren ausgewertet werden. Ihre Performanz reicht für solch umfangreiche Simulationen nicht aus. Diese Dissertation stellt Techniken vor, um diese Werkzeuge zu beschleunigen und somit diese umfangreichen Schaltungen simulieren zu können. Diese Forschungsbeiträge, die sich jeweils über mehrere Veröffentlichungen erstrecken, ermöglichen es Standardwerkzeugen, die Sicherheitstoleranz für kundenspezifische Anwendungsszenarien zu bestimmen. Für eine gegebene Schaltungslebensdauer, Temperatur, Spannung und Aktivität (Schaltverhalten durch Software-Applikationen) können die Auswirkungen der Transistordegradation ausgewertet werden und somit die erforderliche (weder unter- noch überschätzte) Sicherheitstoleranz bestimmt werden. Diese anwendungsspezifische Sicherheitstoleranz, garantiert die Zuverlässigkeit und Funktionalität der Schaltung für genau diese Anwendung bei minimalen Performanzeinbußen

Simulation of Double-Gate Silicon Tunnel FETs with a High-k Gate Dielectric

The down-scaling of conventional MOSFETs has led to an impending power crisis, in which static power consumption is becoming too high. In order to improve the energy-efficiency of electronic circuits, small swing switches are interesting candidates to replace or complement the MOSFETs used today. Tunnel FETs, which are gated p-i-n diodes whose on-current arises from band-to-band tunneling, are attractive new devices for low-power applications due to their low off-current and their potential for a small subthreshold swing. The numerical simulations presented in this thesis have been carried out using a non-local band-to-band tunneling model in Silvaco Atlas. Numerical simulations based on correct underlying models are important for emerging devices, since they can provide insights about optimization before fabrication is carried out, can aid the understanding of device physics through 1D and 2D cross sections, and can be the basis for the formation of an accurate compact model. In general, only CMOS-compatible materials and structures have been used in the Tunnel FET designs presented here. One goal of this thesis was to stay within the framework of what is possible in standard industrial nanoelectronics cleanrooms today, without requiring processes whose mastery lies many years in the future. For this reason, the focus of this thesis is on all-silicon devices, and heterostructures that incorporate other materials are only mentioned. In chapter three, the optimization of the static characteristics of a Tunnel FET is carried out, looking at gate structure (single or double), doping levels of each device region, gate dielectric permittivity, and silicon body thickness. A study of the reduction of the band gap at the tunnel junction is also presented, showing the resulting improvement in on-current and subthreshold swing. Chapter four introduces a new method for threshold voltage extraction in Tunnel FETs. This method has one key advantage over the commonly-used constant current threshold voltage extraction technique: it has a physical meaning. The transconductance method, which has already been used for conventional MOSFETs, pinpoints the Tunnel FET voltage at which the transition from strong control to weak control of the tunneling energy barrier width, and therefore the on-current, takes place. This is analogous to the threshold voltage in a conventional MOSFET which marks the transition from weak inversion to strong inversion at φs=2φF. It is found that Tunnel FETs have two threshold voltages, one in relation to the gate voltage, and the second in relation to the drain voltage, and each depends on the voltage applied at the opposite terminal. A length scaling study is carried out in chapter five, demonstrating the scaling limits of Tunnel FETs at gate lengths on the order of 10-20 nm, due to p-i-n diode leakage current that degrades the off-current. Tunnel FETs designed to have better electrostatic control of the tunnel junction by the gate can scale further before they hit this diode leakage limit at some small gate length. Chapter six presents an additive booster strategy for Tunnel FET optimization, and then uses the resulting optimized device as the basis of a parameter variation study. Here, one parameter is varied at a time, and the effects on the important characteristics (subthreshold swing, threshold voltage, and on-current) are evaluated. The parameters requiring the most control during fabrication are identified. Since Tunnel FETs are emerging devices, the most important future work will be to fabricate fully-optimized n- and p-type devices, and to develop accurate compact models for their incorporation into circuits