Design and analysis of SRAMs for energy harvesting systems

PhD ThesisAt present, the battery is employed as a power source for wide varieties of microelectronic systems ranging from biomedical implants and sensor net-works to portable devices. However, the battery has several limitations and incurs many challenges for the majority of these systems. For instance, the design considerations of implantable devices concern about the battery from two aspects, the toxic materials it contains and its lifetime since replacing the battery means a surgical operation. Another challenge appears in wire-less sensor networks, where hundreds or thousands of nodes are scattered around the monitored environment and the battery of each node should be maintained and replaced regularly, nonetheless, the batteries in these nodes do not all run out at the same time. Since the introduction of portable systems, the area of low power designs has witnessed extensive research, driven by the industrial needs, towards the aim of extending the lives of batteries. Coincidentally, the continuing innovations in the field of micro-generators made their outputs in the same range of several portable applications. This overlap creates a clear oppor-tunity to develop new generations of electronic systems that can be powered, or at least augmented, by energy harvesters. Such self-powered systems benefit applications where maintaining and replacing batteries are impossi-ble, inconvenient, costly, or hazardous, in addition to decreasing the adverse effects the battery has on the environment. The main goal of this research study is to investigate energy harvesting aware design techniques for computational logic in order to enable the capa- II bility of working under non-deterministic energy sources. As a case study, the research concentrates on a vital part of all computational loads, SRAM, which occupies more than 90% of the chip area according to the ITRS re-ports. Essentially, this research conducted experiments to find out the design met-ric of an SRAM that is the most vulnerable to unpredictable energy sources, which has been confirmed to be the timing. Accordingly, the study proposed a truly self-timed SRAM that is realized based on complete handshaking protocols in the 6T bit-cell regulated by a fully Speed Independent (SI) tim-ing circuitry. The study proved the functionality of the proposed design in real silicon. Finally, the project enhanced other performance metrics of the self-timed SRAM concentrating on the bit-line length and the minimum operational voltage by employing several additional design techniques.Umm Al-Qura University, the Ministry of Higher Education in the Kingdom of Saudi Arabia, and the Saudi Cultural Burea

Ultra-low-power SRAM design in high variability advanced CMOS

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2009.Cataloged from PDF version of thesis.Includes bibliographical references (p. 163-181).Embedded SRAMs are a critical component in modern digital systems, and their role is preferentially increasing. As a result, SRAMs strongly impact the overall power, performance, and area, and, in order to manage these severely constrained trade-offs, they must be specially designed for target applications. Highly energy-constrained systems (e.g. implantable biomedical devices, multimedia handsets, etc.) are an important class of applications driving ultra-low-power SRAMs. This thesis analyzes the energy of an SRAM sub-array. Since supply- and threshold-voltage have a strong effect, targets for these are established in order to optimize energy. Despite the heavy emphasis on leakage-energy, analysis of a high-density 256x256 sub-array in 45nm LP CMOS points to two necessary optimizations: (1) aggressive supply-voltage reduction (in addition to Vt elevation), and (2) performance enhancement. Important SRAM metrics, including read/write/hold-margin and read-current, are also investigated to identify trade-offs of these optimizations. Based on the need to lower supply-voltage, a 0.35V 256kb SRAM is demonstrated in 65nm LP CMOS. It uses an 8T bit-cell with peripheral circuit-assists to improve write-margin and bit-line leakage. Additionally, redundancy, to manage the increasing impact of variability in the periphery, is proposed to improve the area-offset trade-off of sense-amplifiers, demonstrating promise for highly advanced technology nodes. Based on the need to improve performance, which is limited by density constraints, a 64kb SRAM, using an offset-compensating sense-amplifier, is demonstrated in 45nm LP CMOS with high-density 0.25[mu]m2 bit-cells.(cont.) The sense-amplifier is regenerative, but non -strobed, overcoming timing uncertainties limiting performance, and it is single-ended, for compatibility with 8T cells. Compared to a conventional strobed sense-amplifier, it achieves 34% improvement in worst-case access-time and 4x improvement in the standard deviation of the access-time.by Naveen Verma.Ph.D

Low-Power, Low-Voltage SRAM Circuits Design For Nanometric CMOS Technologies

Embedded SRAM memory is a vital component in modern SoCs. More than 80% of the System-on-Chip (SoC) die area is often occupied by SRAM arrays. As such, system reliability and yield is largely governed by the SRAM's performance and robustness. The aggressive scaling trend in CMOS device minimum feature size, coupled with the growing demand in high-capacity memory integration, has imposed the use of minimal size devices to realize a memory bitcell. The smallest 6T SRAM bitcell to date occupies a 0.1um2 in silicon area. SRAM bitcells continue to benefit from an aggressive scaling trend in CMOS technologies. Unfortunately, other system components, such as interconnects, experience a slower scaling trend. This has resulted in dramatic deterioration in a cell's ability to drive a heavily-loaded interconnects. Moreover, the growing fluctuation in device properties due to Process, Voltage, and Temperature (PVT) variations has added more uncertainty to SRAM operation. Thus ensuring the ability of a miniaturized cell to drive heavily-loaded bitlines and to generate adequate voltage swing is becoming challenging. A large percentage of state-of-the-art SoC system failures are attributed to the inability of SRAM cells to generate the targeted bitline voltage swing within a given access time. The use of read-assist mechanisms and current mode sense amplifiers are the two key strategies used to surmount bitline loading effects. On the other hand, new bitcell topologies and cell supply voltage management are used to overcome fluctuations in device properties. In this research we tackled conventional 6T SRAM bitcell limited drivability by introducing new integrated voltage sensing schemes and current-mode sense amplifiers. The proposed schemes feature a read-assist mechanism. The proposed schemes' functionality and superiority over existing schemes are verified using transient and statistical SPICE simulations. Post-layout extracted views of the devices are used for realistic simulation results. Low-voltage operated SRAM reliability and yield enhancement is investigated and a wordline boost technique is proposed as a means to manage the cell's WL operating voltage. The proposed wordline driver design shows a significant improvement in reliability and yield in a 400-mV 6T SRAM cell. The proposed wordline driver design exploit the cell's Dynamic Noise Margin (DNM), therefore boost peak level and boost decay rate programmability features are added. SPICE transient and statistical simulations are used to verify the proposed design's functionality. Finally, at a bitcell-level, we proposed a new five-transistor (5T) SRAM bitcell which shows competitive performance and reliability figures of merit compared to the conventional 6T bitcell. The functionality of the proposed cell is verified by post-layout SPICE simulations. The proposed bitcell topology is designed, implemented and fabricated in a standard ST CMOS 65nm technology process. A 1.2_ 1.2 mm2 multi-design project test chip consisting of four 32-Kbit (256-row x 128-column) SRAM macros with the required peripheral and timing control units is fabricated. Two of the designed SRAM macros are dedicated for this work, namely, a 32-Kbit 5T macro and a 32-Kbit 6T macro which is used as a comparison reference. Other macros belong to other projects and are not discussed in this document

Low-power and high-performance SRAM design in high variability advanced CMOS technology

As process technologies shrink, the size and number of memories on a chip are exponentially increasing. Embedded SRAMs are a critical component in modern digital systems, and they strongly impact the overall power, performance, and area. To promote memory-related research in academia, this dissertation introduces OpenRAM, a flexible, portable and open-source memory compiler and characterization methodology for generating and verifying memory designs across different technologies.In addition, SRAM designs, focusing on improving power consumption, access time and bitcell stability are explored in high variability advanced CMOS technologies. To have a stable read/write operation for SRAM in high variability process nodes, a differential-ended single-port 8T bitcell is proposed that improves the read noise margin, write noise margin and readout bitcell current by 45%, 48% and 21%, respectively, compared to a conventional 6T bitcell. Also, a differential-ended single-port 12T bitcell for subthreshold operation is proposed that solves the half-select disturbance and allows efficient bit-interleaving. 12T bitcell has a leakage control mechanism which helps to reduce the power consumption and provides operation down to 0.3 V. Both 8T and 12T bitcells are analyzed in a 64 kb SRAM array using 32 nm technology. Besides, to further improve the access time and power consumption, two tracking circuits (multi replica bitline delay and reconfigurable replica bitline delay techniques) are proposed to aid the generation of accurate and optimum sense amplifier set time.An error tolerant SRAM architecture suitable for low voltage video application with dynamic power-quality management is also proposed in this dissertation. This memory uses three power supplies to improve the SRAM stability in low voltages. The proposed triple-supply approach achieves 63% improvement in image quality and 69% reduction in power consumption compared to a single-supply 64 kb SRAM array at 0.70 V

Circuit design for embedded memory in low-power integrated circuits

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2012.Cataloged from PDF version of thesis.Includes bibliographical references (p. 141-152).This thesis explores the challenges for integrating embedded static random access memory (SRAM) and non-volatile memory-based on ferroelectric capacitor technology-into lowpower integrated circuits. First considered is the impact of process variation in deep-submicron technologies on SRAM, which must exhibit higher density and performance at increased levels of integration with every new semiconductor generation. Techniques to speed up the statistical analysis of physical memory designs by a factor of 100 to 10,000 relative to the conventional Monte Carlo Method are developed. The proposed methods build upon the Importance Sampling simulation algorithm and efficiently explore the sample space of transistor parameter fluctuation. Process variation in SRAM at low-voltage is further investigated experimentally with a 512kb 8T SRAM test chip in 45nm SOI CMOS technology. For active operation, an AC coupled sense amplifier and regenerative global bitline scheme are designed to operate at the limit of on current and off current separation on a single-ended SRAM bitline. The SRAM operates from 1.2 V down to 0.57 V with access times from 400ps to 3.4ns. For standby power, a data retention voltage sensor predicts the mismatch-limited minimum supply voltage without corrupting the contents of the memory. The leakage power of SRAM forces the chip designer to seek non-volatile memory in applications such as portable electronics that retain significant quantities of data over long durations. In this scenario, the energy cost of accessing data must be minimized. This thesis presents a ferroelectric random access memory (FRAM) prototype that addresses the challenges of sensing diminishingly small charge under conditions favorable to low access energy with a time-to-digital sensing scheme. The 1 Mb IT1C FRAM fabricated in 130 nm CMOS operates from 1.5 V to 1.0 V with corresponding access energy from 19.2 pJ to 9.8 pJ per bit. Finally, the computational state of sequential elements interspersed in CMOS logic, also restricts the ability to power gate. To enable simple and fast turn-on, ferroelectric capacitors are integrated into the design of a standard cell register, whose non-volatile operation is made compatible with the digital design flow. A test-case circuit containing ferroelectric registers exhibits non-volatile operation and consumes less than 1.3 pJ per bit of state information and less than 10 clock cycles to save or restore with no minimum standby power requirement in-between active periods.by Masood Qazi.Ph.D

Circuit Techniques for Adaptive and Reliable High Performance Computing.

Increasing power density with process scaling has caused stagnation in the clock speed of modern microprocessors. Accordingly, designers have adopted message passing and shared memory based multicore architectures in order to keep up with the rapidly rising demand for computing throughput. At the same time, applications are not entirely parallel and improving single-thread performance continues to remain critical. Additionally, reliability is also worsening with process scaling, and margining for failures due to process and environmental variations in modern technologies consumes an increasingly large portion of the power/performance envelope. In the wake of multicore computing, reliability of signal synchronization between the cores is also becoming increasingly critical. This forces designers to search for alternate efficient methods to improve compute performance while addressing reliability. Accordingly, this dissertation presents innovative circuit and architectural techniques for variation-tolerance, performance and reliability targeted at datapath logic, signal synchronization and memories. Firstly, a domino logic based design style for datapath logic is presented that uses Adaptive Robustness Tuning (ART) in addition to timing speculation to provide up to 71% performance gains over conventional domino logic in 32bx32b multiplier in 65nm CMOS. Margins are reduced until functionality errors are detected, that are used to guide the tuning. Secondly, for signal synchronization across clock domains, a new class of dynamic logic based synchronizers with single-cycle synchronization latency is presented, where pulses, rather than stable intermediate voltages cause metastability. Such pulses are amplified using skewed inverters to improve mean time between failures by ~1e6x over jamb latches and double flip-flops at 2GHz in 65nm CMOS. Thirdly, a reconfigurable sensing scheme for 6T SRAMs is presented that employs auto-zero calibration and pre-amplification to improve sensing reliability (by up to 1.2 standard deviations of NMOS threshold voltage in 28nm CMOS); this increased reliability is in turn traded for ~42% sensing speedup. Finally, a main memory architecture design methodology to address reliability and power in the context of Exascale computing systems is presented. Based on 3D-stacked DRAMs, the methodology co-optimizes DRAM access energy, refresh power and the increased cost of error resilience, to meet stringent power and reliability constraints.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/107238/1/bharan_1.pd

Novel Non Precharging Single Bitline 8T Static Random Access Memory

Title from PDF of title page viewed August 25, 2017Thesis advisor: Masud H ChowdhuryVitaIncludes bibliographical references (pages 39-41)Thesis (M.S.)--School of Computing and Engineering. University of Missouri-Kansas City, 2016Novel 8T SRAM design, employs individual bit-line (BL) and word-line (WL) for each operation. The read operation uses read word-line (RWL) and read bit-line (RBL) respectively. On other hand the write operation employs write word-line (WWL) and write bit line (WBL). Due to single BL and WL the power consumption of the proposed 8T SRAM cell is significantly less.The proposed design avoids the stability and reliability issues of the conventional 6T and other existing SRAM cells. The read stability and the write ability of the proposed design are better compared to the standard 6T and other 7T, 8T and 9T SRAM designs. The proposed 8T SRAM is as good as the 10T design without the overheads. The power consumption of the proposed 8T SRAM cell is significantly lower than other SRAM cells. The proposed design is ratio-less, which makes the construction and operation of the proposed SRAM much simpler and the response time much faster. The proposed cell design and its reliability and stability have been analyzed for 45nm technology. We have also analyzed the static noise margin (SNM) and the stability of the proposed design. In this analysis, we have used three methods. First, the traditional SNM method with the butterfly curve is introduced. Second, the N-curve method is used. And finally, we used the bit-line voltage method. We have also analyzed the impact of some process and parametric variations. The write ability of the proposed design is also compared to that of the conventional 6T SRAM.Introduction -- Existing SRAM designs -- Proposed 8T SRAM -- Analysis of power and area overheads of the proposed 8T SRAM -- Stability analysis of the proposed 8T SRAM -- Analysis of process and parametric variation in the proposed 8T SRAM -- Monte Carlo analysis -- Conclusio

Novel High Performance Ultra Low Power Static Random Access Memories (SRAMs) Based on Next Generation Technologies

Title from PDF of title page viewed January 27, 2021Dissertation advisor: Masud H. ChowdhuryVitaIncludes bibliographical references (page 107-120)Thesis (Ph.D.)--School of Computing and Engineering. University of Missouri--Kansas City, 2019Next Big Thing Is Surely Small: Nanotechnology Can Bring Revolution. Nanotechnology leads the world towards many new applications in various fields of computing, communication, defense, entertainment, medical, renewable energy and environment. These nanotechnology applications require an energy-efficient memory system to compute and process. Among all the memories, Static Random Access Memories (SRAMs) are high performance memories and occupies more than 50% of any design area. Therefore, it is critical to design high performance and energy-efficient SRAM design. Ultra low power and high speed applications require a new generation memory capable of operating at low power as well as low execution time. In this thesis, a novel 8T SRAM design is proposed that offers significantly faster access time and lowers energy consumption along with better read stability and write ability. The proposed design can be used in the conventional SRAM as well as in computationally intensive applications like neural networks and machine learning classifiers [1]-[4]. Novel 8T SRAM design offers higher energy efficiency, reliability, robustness and performance compared to the standard 6T and other existing 8T and 9T designs. It offers the advantages of a 10T SRAM without the additional area, delay and power overheads of the 10T SRAM. The proposed 8T SRAM would be able to overcome many other limitations of the conventional 6T and other 7T, 8T and 9T designs. The design employs single bitline for the write operation, therefore the number of write drivers are reduced. The defining feature of the proposed 8T SRAM is its hybrid design, which is the combination of two techniques: (i) the utilization of single-ended bitline and (ii) the utilization of virtual ground. The single-ended bitline technique ensures separate read and write operations, which eventually reduces the delay and power consumption during the read and write operations. It's independent read and write paths allow the use of the minimum sized access transistors and aid in a disturb-free read operation. The virtual ground weakens the positive feedback in the SRAM cell and improves its write ability. The virtual ground technique is also used to reduce leakages. The proposed design does not require precharging the bitlines for the read operation, which reduces the area and power overheads of the memory system by eliminating the precharging circuit. The design isolates the storage node from the read path, which improves the read stability. For reliability study, we have investigated the static noise margin (SNM) of the proposed 8T SRAM, for which, we have used two methods – (i) the traditional SNM method with the butterfly curve, (ii) the N-curve method A comparative analysis is performed between the proposed and the existing SRAM designs in terms of area, total power consumption during the read and write operations, and stability and reliability. All these advantages make the proposed 8T SRAM design an ideal candidate for the conventional and computationally intensive applications like machine learning classifier and deep learning neural network. In addition to this, there is need for next generation technologies to design SRAM memory because the conventional CMOS technology is approaching its physical and performance boundaries and as a consequence, becoming incompatible with ultra-low-power applications. Emerging devices such as Tunnel Field Effect Transistor (TFET)) and Graphene Nanoribbon Field Effect Transistor (GNRFET) devices are highly potential candidates to overcome the limitations of MOSFET because of their ability to achieve subthreshold slopes below 60 mV/decade and very low leakage currents [6]-[9]. This research also explores novel TFET and GNRFET based 6T SRAM. The thesis evaluates the standby leakage power in the Tunnel FET (TFET) based 6T SRAM cell for different pull-up, pull-down, and pass-gate transistors ratios (PU: PD: PG) and compared to 10nm FinFET based 6T SRAM designs. It is observed that the 10nm TFET based SRAMs have 107.57%, 163.64%, and 140.44% less standby leakage power compared to the 10nm FinFET based SRAMs when the PU: PD: PG ratios are 1:1:1, 1:5:2 and 2:5:2, respectively. The thesis also presents an analysis of the stability and reliability of sub-10nm TFET based 6T SRAM circuit with a reduced supply voltage of 500mV. The static noise margin (SNM), which is a critical measure of SRAM stability and reliability, is determined for hold, read and write operations of the 6T TFET SRAM cell. The robustness of the optimized TFET based 6T SRAM circuit is also evaluated at different supply voltages. Simulations were done in HSPICE and Cadence tools. From the analysis, it is clear that the main advantage of the TFET based SRAM would be the significant improvement in terms of leakage or standby power consumption. Compared to the FinFET based SRAM the standby leakage power of the T-SRAMs are 107.57%, 163.64%, and 140.44% less for 1:1:1, 1:5:2 and 2:5:2 configurations, respectively. Since leakage/standby power is the primary source of power consumption in the SRAM, and the overall system energy efficiency depends on SRAM power consumption, TFET based SRAM would lead to massive improvement of the energy efficiency of the system. Therefore, T-SRAMs are more suitable for ultra-low power applications. In addition to this, the thesis evaluates the standby leakage power of types of Graphene Nanoribbon FETs based 6T SRAM bitcell and compared to 10nm FinFET based 6T SRAM bitcell. It is observed that the 10nm MOS type GNRFET based SRAMs have 16.43 times less standby leakage power compared to the 10nm FinFET based SRAMs. The double gate SB-GNRFET based SRAM consumes 1.35E+03 times less energy compared to the 10nm FinFET based SRAM during write. However, during read double gate SB-GNRFET based SRAM consume 15 times more energy than FinFET based SRAM. It is also observed that GNRFET based SRAMs are more stable and reliable than FinFET based SRAM.Introduction -- Background -- Novel High Performance Ultra Low Power SRAM Design -- Tunnel FET Based SRAM Design -- Graphene Nanoribbon FET Based SRAM Design -- Double-gate FDSOI Based SRAM Designs -- Novel CNTFET and MEMRISTOR Based Digital Designs -- Conclusio

Ultra Low Power Digital Circuit Design for Wireless Sensor Network Applications

Ny forskning innenfor feltet trådløse sensornettverk åpner for nye og innovative produkter og løsninger. Biomedisinske anvendelser er blant områdene med størst potensial og det investeres i dag betydelige beløp for å bruke denne teknologien for å gjøre medisinsk diagnostikk mer effektiv samtidig som man åpner for fjerndiagnostikk basert på trådløse sensornoder integrert i et ”helsenett”. Målet er å forbedre tjenestekvalitet og redusere kostnader samtidig som brukerne skal oppleve forbedret livskvalitet som følge av økt trygghet og mulighet for å tilbringe mest mulig tid i eget hjem og unngå unødvendige sykehusbesøk og innleggelser. For å gjøre dette til en realitet er man avhengige av sensorelektronikk som bruker minst mulig energi slik at man oppnår tilstrekkelig batterilevetid selv med veldig små batterier. I sin avhandling ” Ultra Low power Digital Circuit Design for Wireless Sensor Network Applications” har PhD-kandidat Farshad Moradi fokusert på nye løsninger innenfor konstruksjon av energigjerrig digital kretselektronikk. Avhandlingen presenterer nye løsninger både innenfor aritmetiske og kombinatoriske kretser, samtidig som den studerer nye statiske minneelementer (SRAM) og alternative minnearkitekturer. Den ser også på utfordringene som oppstår når silisiumteknologien nedskaleres i takt med mikroprosessorutviklingen og foreslår løsninger som bidrar til å gjøre kretsløsninger mer robuste og skalerbare i forhold til denne utviklingen. De viktigste konklusjonene av arbeidet er at man ved å introdusere nye konstruksjonsteknikker både er i stand til å redusere energiforbruket samtidig som robusthet og teknologiskalerbarhet øker. Forskningen har vært utført i samarbeid med Purdue University og vært finansiert av Norges Forskningsråd gjennom FRINATprosjektet ”Micropower Sensor Interface in Nanometer CMOS Technology”