Latest Developments in Industrial Hybrid Machine Tools that Combine Additive and Subtractive Operations

Hybrid machine tools combining additive and subtractive processes have arisen as a solution to increasing manufacture requirements, boosting the potentials of both technologies, while compensating and minimizing their limitations. Nevertheless, the idea of hybrid machines is relatively new and there is a notable lack of knowledge about the implications arisen from their in-practice use. Therefore, the main goal of the present paper is to fill the existing gap, giving an insight into the current advancements and pending tasks of hybrid machines both from an academic and industrial perspective. To that end, the technical-economical potentials and challenges emerging from their use are identified and critically discussed. In addition, the current situation and future perspectives of hybrid machines from the point of view of process planning, monitoring, and inspection are analyzed. On the one hand, it is found that hybrid machines enable a more efficient use of the resources available, as well as the production of previously unattainable complex parts. On the other hand, it is concluded that there are still some technological challenges derived from the interaction of additive and subtractive processes to be overcome (e.g., process planning, decision planning, use of cutting fluids, and need for a post-processing) before a full implantation of hybrid machines is fulfilledSpecial thanks are addressed to the Industry and Competitiveness Spanish Ministry for the support on the DPI2016-79889-R INTEGRADDI project and to the PARADDISE project H2020-IND-CE-2016-17/H2020-FOF-2016 of the European Union's Horizon 2020 research and innovation program

Surface profile prediction and analysis applied to turning process

An approach for the prediction of surface profile in turning process using Radial Basis Function (RBF) neural networks is presented. The input parameters of the RBF networks are cutting speed, depth of cut and feed rate. The output parameters are Fast Fourier Transform (FFT) vector of surface profile for the prediction of surface profile. The RBF networks are trained with adaptive optimal training parameters related to cutting parameters and predict surface profile using the corresponding optimal network topology for each new cutting condition. A very good performance of surface profile prediction, in terms of agreement with experimental data, was achieved with high accuracy, low cost and high speed. It is found that the RBF networks have the advantage over Back Propagation (BP) neural networks. Furthermore, a new group of training and testing data were also used to analyse the influence of tool wear and chip formation on prediction accuracy using RBF neural networks

On the Machinability of an Al-63%SiC Metal Matrix Composite

This paper presents a preliminary study of aluminium matrix composite materials during machining, with a special focus on their behavior under conventional processes. This work will expand the knowledge of these materials, which is considered to be strategic for some industrial sectors, such as the aeronautics, electronics, and automotive sectors. Finding a machining model will allow us to define the necessary parameters when applying the materials to industry. As a previous step of the material and its machining, an experimental state-of-the-art review has been carried out, revealing a lack of studies about the composition and material properties, processes, tools, and recommended parameters. The results obtained and reflected in this paper are as follows; SiC is present in metallic matrix composite (MMC) materials in a very wide variety of sizes. A metallographic study of the material confirms the high percentage of reinforcement and very high microhardness values registered. During the machining process, tools present a very high level of wear in a very short amount of time, where chips are generated and arcs are segmented, revealing the high microhardness of the material, which is given by its high concentration of SiC. The chip shape is the same among other materials with a similar microhardness, such as Ti or its alloys. The forces registered in the machining process are quite di erent from conventional alloys and are more similar to the values of harder alloys, which is also the case for chip generation. The results coincide, in part, with previous studies and also give new insight into the behavior of this material, which does not conform to the assumptions for standard metallic materials, where the hypothesis of Sha er is not directly applicable. On the other hand, here, cutting forces do not behave in accordance with the traditional model. This paper will contribute to improve the knowledge of the Al-63%SiC MMC itself and the machining behavior

An experimental study of the effect of high-pressure water jet assisted turning (HPWJAT) on the surface integrity

This study deals with the effect of High-Pressure Water Jet Assisted Turning (HPWJAT) of austenitic stainless steels on chip shape and residual stresses. The machining of the austenitic stainless steels represents several difficulties. Recently, research has shown that the introduction of a high-pressure water jet into the gap between the tool and the chip interface is a very satisfactory method for machining applications. In this article, the effect of a high-pressure water jet, directed into the tool–chip interface, on chip shapes breakage and surface integrity in face turning operations of AISI 316L steel has been investigated. Tests have been carried out with a standard cutting tool. The cutting speeds used were 80 and 150 m/min, with a constant feed rate of 0.1 mm/rev and a constant cutting depth of 1 mm. Three jet pressures were used: 20, 50 and 80 MPa. Residual stress profiles have been analysed using the X-ray diffraction method in both longitudinal and transversal directions. The results show that jet pressure and cutting parameters influence the residual stresses and the chip shapes. Using a high-pressure jet, it is possible to create a well fragmented chip in contrast to the continuous chip formed using dry turning. It is also possible to control the chip shape and increase tool life. When the jet pressure is increased the residual stress at the surface decreases; however it is increased by an increase in cutting speed. It can be concluded that surface residual stresses can be reduced by the introduction of a high-pressure water jet

Differential Scanning Calorimetric (DSC) Study of New and Sterilized Nickel-Titanium Rotary Endodontic Instruments

Introduction: Nickel-Titanium (NiTi) files have become popular in endodontic procedures compared to traditional stainless steel hand files owing to their increased flexibility which is especially advantageous in curved canals. Due to the associated costs, endodontic instruments are frequently re-used, which requires sterilization between uses. With the application of temperature NiTi has the ability to undergo phase transformations, altering the properties of the instruments. The purpose of this study was to investigate phase transformations of four brands of NiTi rotary endodontic instruments in the as-received condition and after multiple sterilization cycles under steam sterilization, using differential scanning calorimetry. Materials and Methods: Four brands of nickel-titanium endodontic rotary files size 35, .04 taper were evaluated in this study: ProFile (Dentsply Tulsa Dental Specialties, Tulsa, OK), ProFile Vortex (Dentsply), Vortex Blue (Dentsply), and HyFlex CM (Coltène/Whaledent, Cuyahoga Falls, OH). The transformation temperatures and phase transformations of these files were determined in the as-received condition and after 1, 3, and 5 cycles of steam sterilization by differential scanning calorimetry. Measurements were analyzed using a two-way ANOVA. Results: There were significant differences between file brands in austenite finish temperature (p \u3c 0.05) but the only statistical significant differences in thermal properties when comparing files before and after 1, 3, and 5 cycles of steam sterilization were found with onset heating (p \u3c 0.05). Conclusion: Repeated cycles of steam sterilization do not appear to influence the phase transformations of NiTi endodontic instruments

Feasibility of remotely manipulated welding in space. A step in the development of novel joining technologies

In order to establish permanent human presence in space technologies of constructing and repairing space stations and other space structures must be developed. Most construction jobs are performed on earth and the fabricated modules will then be delivered to space by the Space Shuttle. Only limited final assembly jobs, which are primarily mechanical fastening, will be performed on site in space. Such fabrication plans, however, limit the designs of these structures, because each module must fit inside the transport vehicle and must withstand launching stresses which are considerably high. Large-scale utilization of space necessitates more extensive construction work on site. Furthermore, continuous operations of space stations and other structures require maintenance and repairs of structural components as well as of tools and equipment on these space structures. Metal joining technologies, and especially high-quality welding, in space need developing

A comparison of processing techniques for producing prototype injection moulding inserts.

This project involves the investigation of processing techniques for producing low-cost moulding inserts used in the particulate injection moulding (PIM) process. Prototype moulds were made from both additive and subtractive processes as well as a combination of the two. The general motivation for this was to reduce the entry cost of users when considering PIM. PIM cavity inserts were first made by conventional machining from a polymer block using the pocket NC desktop mill. PIM cavity inserts were also made by fused filament deposition modelling using the Tiertime UP plus 3D printer. The injection moulding trials manifested in surface finish and part removal defects. The feedstock was a titanium metal blend which is brittle in comparison to commodity polymers. That in combination with the mesoscale features, small cross-sections and complex geometries were considered the main problems. For both processing methods, fixes were identified and made to test the theory. These consisted of a blended approach that saw a combination of both the additive and subtractive processes being used. The parts produced from the three processing methods are investigated and their respective merits and issues are discussed