Asymmetric clock driver for improved power and noise performances

One of the most important sources of switching noise and power consumption in large VLSI circuits is the clock generation and distribution tree. This paper analyzes how the use of an asymmetric clock can be an important solution to reduce the switching noise generated by the global clock, with a very reduced degradation in performances and reliability. The suited sizing of clock generators and the design of asymmetric clock tree cells, show the benefits of the proposed technique, validated through a design example where a 50% of noise reduction is achieved with 10% of loss in operation frequency and no penalty, even saving, in power consumption.Ministerio de Educación y Ciencia TEC2004-01509Junta de Andalucía TIC2006-63

Energy-Efficient Digital Circuit Design using Threshold Logic Gates

abstract: Improving energy efficiency has always been the prime objective of the custom and automated digital circuit design techniques. As a result, a multitude of methods to reduce power without sacrificing performance have been proposed. However, as the field of design automation has matured over the last few decades, there have been no new automated design techniques, that can provide considerable improvements in circuit power, leakage and area. Although emerging nano-devices are expected to replace the existing MOSFET devices, they are far from being as mature as semiconductor devices and their full potential and promises are many years away from being practical. The research described in this dissertation consists of four main parts. First is a new circuit architecture of a differential threshold logic flipflop called PNAND. The PNAND gate is an edge-triggered multi-input sequential cell whose next state function is a threshold function of its inputs. Second a new approach, called hybridization, that replaces flipflops and parts of their logic cones with PNAND cells is described. The resulting \hybrid circuit, which consists of conventional logic cells and PNANDs, is shown to have significantly less power consumption, smaller area, less standby power and less power variation. Third, a new architecture of a field programmable array, called field programmable threshold logic array (FPTLA), in which the standard lookup table (LUT) is replaced by a PNAND is described. The FPTLA is shown to have as much as 50% lower energy-delay product compared to conventional FPGA using well known FPGA modeling tool called VPR. Fourth, a novel clock skewing technique that makes use of the completion detection feature of the differential mode flipflops is described. This clock skewing method improves the area and power of the ASIC circuits by increasing slack on timing paths. An additional advantage of this method is the elimination of hold time violation on given short paths. Several circuit design methodologies such as retiming and asynchronous circuit design can use the proposed threshold logic gate effectively. Therefore, the use of threshold logic flipflops in conventional design methodologies opens new avenues of research towards more energy-efficient circuits.Dissertation/ThesisDoctoral Dissertation Computer Science 201

High Peformance and Low Power On-Die Interconnect Fabrics.

Increasing power density with technology scaling has caused stagnation in operating frequency of modern day microprocessors. This has led designers to prefer multicore architectures over complex monolithic processors to keep up with the demand for rising computing throughput. Although processing units are getting smaller and simpler, the dramatic rise of their count on a single die has made the fabric that connects these processing units increasingly complex. These interconnect fabrics have become a bottleneck in improving overall system effciency. As a result, the design paradigm for multi-core chips is gradually shifting from a core-centric architecture towards an interconnect-centric architecture, where system efficiency is limited by the fabric rather than the processing ability of any individual core. This dissertation introduces three novel and synergistic circuit techniques to improve scalability of switch fabrics to make on-die integration of hundreds to thousands of cores feasible. 1) A matrix topology is proposed for designing a fully connected switch fabric that re-uses output buses for programming, and stores shue congurations at cross points. This significantly reduces routing congestion, lowers area/power, and improves per- formance. Silicon measurements demonstrate 47% energy savings in a 64-lane SIMD processor fabricated in 65nm CMOS over a conventional implementation. 2) A novel approach to handle high radix arbitration along with data routing is proposed. It optimally uses existing cross-bar interconnect resources without requiring any additional overhead. Bandwidth exceeding 2Tb/s is recorded in a test prototype fabricated in 65nm. 3) Building on the later, a new circuit topology to manage and update priority adaptively within the switch fabric without incurring additional delay or area is then proposed. Several assist circuit techniques, such as a thyristor based sense amplifier and self regenerating bi-directional repeaters are proposed for high speed energy efficient signaling to and from the switch fabric to improve overall routing efficiency. Using these techniques a 64 x 64 switch fabric with 128b data bus fabricated in 45nm achieves a throughput of 4.5Tb/s at single cycle latency while operating at 559MHz.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/91506/1/sudhirks_1.pd

High-Speed and Low-Energy On-Chip Communication Circuits.

Continuous technology scaling sharply reduces transistor delays, while fixed-length global wire delays have increased due to less wiring pitch with higher resistance and coupling capacitance. Due to this ever growing gap, long on-chip interconnects pose well-known latency, bandwidth, and energy challenges to high-performance VLSI systems. Repeaters effectively mitigate wire RC effects but do little to improve their energy costs. Moreover, the increased complexity and high level of integration requires higher wire densities, worsening crosstalk noise and power consumption of conventionally repeated interconnects. Such increasing concerns in global on-chip wires motivate circuits to improve wire performance and energy while reducing the number of repeaters. This work presents circuit techniques and investigation for high-performance and energy-efficient on-chip communication in the aspects of encoding, data compression, self-timed current injection, signal pre-emphasis, low-swing signaling, and technology mapping. The improved bus designs also consider the constraints of robust operation and performance/energy gains across process corners and design space. Measurement results from 5mm links on 65nm and 90nm prototype chips validate 2.5-3X improvement in energy-delay product.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/75800/1/jseo_1.pd

Reservoir Computing with Boolean Logic Network Circuits

To push the frontiers of machine learning, completely new computing architectures must be explored which efficiently use hardware resources. We test an unconventional use of digital logic gate circuits for reservoir computing, a machine learning algorithm that is used for rapid time series processing. In our approach, logic gates are configured into networks that can exhibit complex dynamics. Rather than the gates explicitly computing pre-programmed instructions, they are used collectively as a dynamical system that transforms input data into a higher dimensional representation. We probe the dynamics of such circuits using discrete components on a circuit board as well as an FPGA implementation. We show favorable machine learning performance, including radiofrequency classification accuracy comparableto a state of the art convolutional neural network with a fraction of the trainable parameters. Finally, we discuss the design and fabrication of a reservoir computing ASIC for high-speed time series processing