Enhanced Hardware Security Using Charge-Based Emerging Device Technology

The emergence of hardware Trojans has largely reshaped the traditional view that the hardware layer can be blindly trusted. Hardware Trojans, which are often in the form of maliciously inserted circuitry, may impact the original design by data leakage or circuit malfunction. Hardware counterfeiting and IP piracy are another two serious issues costing the US economy more than $200 billion annually. A large amount of research and experimentation has been carried out on the design of these primitives based on the currently prevailing CMOS technology. However, the security provided by these primitives comes at the cost of large overheads mostly in terms of area and power consumption. The development of emerging technologies provides hardware security researchers with opportunities to utilize some of the otherwise unusable properties of emerging technologies in security applications. In this dissertation, we will include the security consideration in the overall performance measurements to fully compare the emerging devices with CMOS technology. The first approach is to leverage two emerging devices (Silicon NanoWire and Graphene SymFET) for hardware security applications. Experimental results indicate that emerging device based solutions can provide high level circuit protection with relatively lower performance overhead compared to conventional CMOS counterpart. The second topic is to construct an energy-efficient DPA-resilient block cipher with ultra low-power Tunnel FET. Current-mode logic is adopted as a circuit-level solution to countermeasure differential power analysis attack, which is mostly used in the cryptographic system. The third investigation targets on potential security vulnerability of foundry insider\u27s attack. Split manufacturing is adopted for the protection on radio-frequency (RF) circuit design

Interval Bisection Quantization Circuit for an 8-Bit Analog to Digital Converter

A common type of analog to digital converter (ADC) is called the successive approximation ADC. It works by setting each bit in the digital output code individually and thus its conversion time is determined by the clock frequency and the resolution of the converter. A speed improvement may be made by using a quantization circuit that sets the entire output code at once. The goal of this project is to design such a quantization circuit based on the interval bisection algorithm. The circuit was designed using Cadence Schematic and Virtuoso and was simulated using spice. Spice simulations show that, on average, the circuit converts faster than the conventional successive approximation converter.Electrical and Computer Engineering, Department o

Phase Noise Analyses and Measurements in the Hybrid Memristor-CMOS Phase-Locked Loop Design and Devices Beyond Bulk CMOS

Phase-locked loop (PLLs) has been widely used in analog or mixed-signal integrated circuits. Since there is an increasing market for low noise and high speed devices, PLLs are being employed in communications. In this dissertation, we investigated phase noise, tuning range, jitter, and power performances in different architectures of PLL designs. More energy efficient devices such as memristor, graphene, transition metal di-chalcogenide (TMDC) materials and their respective transistors are introduced in the design phase-locked loop. Subsequently, we modeled phase noise of a CMOS phase-locked loop from the superposition of noises from its building blocks which comprises of a voltage-controlled oscillator, loop filter, frequency divider, phase-frequency detector, and the auxiliary input reference clock. Similarly, a linear time-invariant model that has additive noise sources in frequency domain is used to analyze the phase noise. The modeled phase noise results are further compared with the corresponding phase-locked loop designs in different n-well CMOS processes. With the scaling of CMOS technology and the increase of the electrical field, the problem of short channel effects (SCE) has become dominant, which causes decay in subthreshold slope (SS) and positive and negative shifts in the threshold voltages of nMOS and pMOS transistors, respectively. Various devices are proposed to continue extending Moore\u27s law and the roadmap in semiconductor industry. We employed tunnel field effect transistor owing to its better performance in terms of SS, leakage current, power consumption etc. Applying an appropriate bias voltage to the gate-source region of TFET causes the valence band to align with the conduction band and injecting the charge carriers. Similarly, under reverse bias, the two bands are misaligned and there is no injection of carriers. We implemented graphene TFET and MoS2 in PLL design and the results show improvements in phase noise, jitter, tuning range, and frequency of operation. In addition, the power consumption is greatly reduced due to the low supply voltage of tunnel field effect transistor

Frequency Synthesis in Wireless and Wireline Systems

First, a frequency synthesizer for IEEE 802.15.4 / ZigBee transceiver applications that employs dynamic True Single Phase Clocking (TSPC) circuits in its frequency dividers is presented and through the analysis and measurement results of this synthesizer, the need for low power circuit techniques in frequency dividers is discussed. Next, Differential Cascode Voltage-Switch-Logic (DCVSL) based delay cells are explored for implementing radio-frequency (RF) frequency dividers of low power frequency synthesizers. DCVSL ip- ops offer small input and clock capacitance which makes the power consumption of these circuits and their driving stages, very low. We perform a delay analysis of DCVSL circuits and propose a closed-form delay model that predicts the speed of DCVSL circuits with 8 percent worst case accuracy. The proposed delay model also demonstrates that DCVSL circuits suffer from a large low-to-high propagation delay ( PLH) which limits their speed and results in asymmetrical output waveforms. Our proposed enhanced DCVSL, which we call DCVSL-R, solves this delay bottleneck, reducing PLH and achieving faster operation. We implement two ring-oscillator-based voltage controlled oscillators (VCOs) in 0.13 mu m technology with DCVSL and DCVSL-R delay cells. In measurements, for the same oscillation frequency (2.4GHz) and same phase noise (-113dBc/Hz at 10MHz), DCVSL-R VCO consumes 30 percent less power than the DCVSL VCO. We also use the proposed DCVSL-R circuit to implement the 2.4GHz dual-modulus prescaler of a low power frequency synthesizer in 0.18 mu m technology. In measurements, the synthesizer exhibits -135dBc/Hz phase noise at 10MHz offset and 58 mu m settling time with 8.3mW power consumption, only 1.07mWof which is consumed by the dual modulus prescaler and the buffer that drives it. When compared to other dual modulus prescalers with similar division ratios and operating frequencies in literature, DCVSL-R dual modulus prescaler demonstrates the lowest power consumption. An all digital phase locked loop (ADPLL) that operates for a wide range of frequencies to serve as a multi-protocol compatible PLL for microprocessor and serial link applications, is presented. The proposed ADPLL is truly digital and is implemented in a standard complementary metal-oxide-semiconductor (CMOS) technology without any analog/RF or non-scalable components. It addresses the challenges that come along with continuous wide range of operation such as stability and phase frequency detection for a large frequency error range. A proposed multi-bit bidirectional smart shifter serves as the digitally controlled oscillator (DCO) control and tunes the DCO frequency by turning on/off inverter units in a large row/column matrix that constitute the ring oscillator. The smart shifter block is completely digital, consisting of standard cell logic gates, and is capable of tracking the row/column unit availability of the DCO and shifting multiple bits per single update cycle. This enables fast frequency acquisition times without necessitating dual loop fi lter or gear shifting mechanisms. The proposed ADPLL loop architecture does not employ costly, cumbersome DACs or binary to thermometer converters and minimizes loop filter and DCO control complexity. The wide range ADPLL is implemented in 90nm digital CMOS technology and has a 9-bit TDC, the output of which is processed by a 10-bit digital loop filter and a 5-bit smart shifter. In measurements, the synthesizer achieves 2.5GHz-7.3GHz operation while consuming 10mW/GHz power, with an active area of 0.23 mm2

Architectural Alternatives to Implement High-Performance Delta-Sigma Modulators

RÉSUMÉ Le besoin d’appareils portatifs, de téléphones intelligents et de systèmes microélectroniques implantables médicaux s’accroît remarquablement. Cependant, l’optimisation de l’alimentation de tous ces appareils électroniques portables est l’un des principaux défis en raison du manque de piles à grande capacité utilisées pour les alimenter. C’est un fait bien établi que le convertisseur analogique-numérique (CAN) est l’un des blocs les plus critiques de ces appareils et qu’il doit convertir efficacement les signaux analogiques au monde numérique pour effectuer un post-traitement tel que l’extraction de caractéristiques. Parmi les différents types de CAN, les modulateurs Delta Sigma (��M) ont été utilisés dans ces appareils en raison des fonctionnalités alléchantes qu’ils offrent. En raison du suréchantillonnage et pour éloigner le bruit de la bande d’intérêt, un CAN haute résolution peut être obtenu avec les architectures ��. Il offre également un compromis entre la fréquence d’échantillonnage et la résolution, tout en offrant une architecture programmable pour réaliser un CAN flexible. Ces CAN peuvent être implémentés avec des blocs analogiques de faible précision. De plus, ils peuvent être efficacement optimisés au niveau de l’architecture et circuits correspondants. Cette dernière caractéristique a été une motivation pour proposer différentes architectures au fil des ans. Cette thèse contribue à ce sujet en explorant de nouvelles architectures pour optimiser la structure ��M en termes de résolution, de consommation d’énergie et de surface de silicium. Des soucis particuliers doivent également être pris en compte pour faciliter la mise en œuvre du ��M. D’autre part, les nouveaux procédés CMOS de conception et fabrication apportent des améliorations remarquables en termes de vitesse, de taille et de consommation d’énergie lors de la mise en œuvre de circuits numériques. Une telle mise à l’échelle agressive des procédés, rend la conception de blocs analogiques tel que un amplificateur de transconductance opérationnel (OTA), difficile. Par conséquent, des soins spéciaux sont également pris en compte dans cette thèse pour surmonter les problèmes énumérés. Ayant mentionné ci-dessus que cette thèse est principalement composée de deux parties principales. La première concerne les nouvelles architectures implémentées en mode de tension et la seconde partie contient une nouvelle architecture réalisée en mode hybride tension et temps.----------ABSTRACT The need for hand-held devices, smart-phones and medical implantable microelectronic sys-tems, is remarkably growing up. However, keeping all these electronic devices power optimized is one of the main challenges due to the lack of long life-time batteries utilized to power them up. It is a well-established fact that analog-to-digital converter (ADC) is one of the most critical building blocks of such devices and it needs to efficiently convert analog signals to the digital world to perform post processing such as channelizing, feature extraction, etc. Among various type of ADCs, Delta Sigma Modulators (��Ms) have been widely used in those devices due to the tempting features they offer. In fact, due to oversampling and noise-shaping technique a high-resolution ADC can be achieved with �� architectures. It also offers a compromise between sampling frequency and resolution while providing a highly-programmable approach to realize an ADC. Moreover, such ADCs can be implemented with low-precision analog blocks. Last but not the least, they are capable of being effectively power optimized at both architectural and circuit levels. The latter has been a motivation to proposed different architectures over the years.This thesis contributes to this topic by exploring new architectures to effectively optimize the ��M structure in terms of resolution, power consumption and chip area. Special cares must also be taken into account to ease the implementation of the ��M. On the other hand, advanced node CMOS processes bring remarkable improvements in terms of speed, size and power consumption while implementing digital circuits. Such an aggressive process scaling, however, make the design of analog blocks, e.g. operational transconductance amplifiers (OTAs), cumbersome. Therefore, special cares are also taken into account in this thesis to overcome the mentioned issues. Having had above mentioned discussion, this thesis is mainly split in two main categories. First category addresses new architectures implemented in a pure voltage domain and the second category contains new architecture realized in a hybrid voltage and time domain. In doing so, the thesis first focuses on a switched-capacitor implementation of a ��M while presenting an architectural solution to overcome the limitations of the previous approaches. This limitations include a power hungry adder in a conventional feed-forward topology as well as power hungry OTAs

Low phase noise 2 GHz Fractional-N CMOS synthesizer IC

Low noise low division 2 GHz RF synthesizer integrated circuits (ICs) are conventionally implemented in some form of HBT process such as SiGe or GaAs. The research in this dissertation differs from convention, with the aim of implementing a synthesizer IC in a more convenient, low-cost Si-based CMOS process. A collection of techniques to push towards the noise and frequency limits of CMOS processes, and possibly other IC processes, is then one of the research outcomes. In a synthesizer low N-divider ratios are important, as high division ratios would amplify in-band phase noise. The design methods deployed as part of this research achieve low division ratios (4 ≤ N ≤ 33) and a high phase comparison frequency (>100 MHz). The synthesizer IC employs a first-order fractional-N topology to achieve increased frequency tuning resolution. The primary N-divider was implemented utilising current mode logic (CML) and the fractional accumulator utilising conventional CMOS. Both a conventional CMOS phase frequency detector (PFD) and a CML PFD were implemented for benchmarking purposes. A custom-built 4.4 GHz synthesizer circuit employing the IC was used to validate the research. In the 4.4 GHz synthesizer circuit, the prototype IC achieved a measured in-band phase noise plateau of L( f ) = -113 dBc/Hz at a 100 kHz frequency offset, which equates to a figure of merit (FOM) of -225 dBc/Hz. The FOM compares well with existing, but expensive, SiGe and GaAs HBT processes. Total IC power dissipation was 710 mW, which is considerably less than commercially available GaAs designs. The complete synthesizer IC was implemented in Austriamicrosystems‟ (AMS) 0.35 μm CMOS process and occupies an area of 3.15 x 2.18 mm2.Dissertation (MEng)--University of Pretoria, 2010.Electrical, Electronic and Computer Engineeringunrestricte

High-speed low-power modulator driver arrays for medium-reach optical networks

The internet is becoming the ubiquitous tool that is changing the lives of so many citizens across the world. Commerce, government, industry, healthcare and social interactions are all increasingly using internet applications to improve and facilitate communications. This is especially true for videoenabled applications, which currently demand much higher data rates and quality from data networks. High definition TV streaming services are emerging and these again will significantly push the demand for widely deployed, high-bandwidth services. The current access passive optical networks (PONs) use a single wavelength for downstream transmission and a separate one for upstream transmission. Incorporating wavelength-division multiplexing (WDM) in a PON allows for much higher bandwidths in both directions. While WDM technologies have been successfully deployed for many years in metro and core networks, in access networks they are not commonly used yet. This is mainly due to the high costs associated with deploying entire WDM access networks. However, the present optical networks cannot be simply and cost-effectively scaled to provide the capacity for tomorrow’s users. As an effect there is a strong need for new WDM access components which are compact, cost-competitive and mass-manufacturable. Increasing the number of wavelengths for WDM-PON automatically leads to an increase in the number of single pluggable transceivers, which brings substantial design challenges and additional costs. The multitude of TXs and RXs for different wavelength channels increases the total footprint considerably. Photonic integration of transceivers into arrays will significantly reduce the footprint and cost. However, the total power consumption of an array device is an issue. To avoid the use of a thermoelectric cooler, the integration density of components is severely limited by the heat dissipating capabilities offered by their package. As a result the WDM-PON philosophy necessitates the reduction of the transceiver’s power dissipation. From this plea it is apparent that the main technology challenges for realizing future-proof optical (access) networks are reducing active component power consumption, shrinking form factors and lowering assembly costs. In this perspective an over 100 Gb/s throughput component, composed of 10 channels at 11.3 Gb/s per wavelength channel would be a great contribution to the expansion of customer bandwidth. It can provide increased line rates to the end users at speeds of 10 Gb/s per wavelength. As RXs typically consume much less power than externally modulated TXs, they can relatively easily be integrated into an array. Mainly high speed optical transmitters have significant power consumptions and the heat generation caused by power dissipation forms a critical obstacle in the development of a 10-channel transmitter, which again underlines the importance of power reduction. Alongside the introduction of WDM in access networks, also inter-office point-to-point connections in data center environments could benefit from the WDM philosophy. As data center operators often suffer from fiber scarcity or do not own their fiber infrastructure, WDM technologies are essential to deliver reach and capacity extension for these scenarios. Interdata center communication also benefits from cost-, footprint- and energyefficient components operating at high speed to maximize the throughput. As an effect integrated over 100 Gb/s transceivers, such as 4 channels at 28 Gb/s, are highly desirable. The research described in this dissertation was partly funded by the European FP7 ICT project C3PO (Colourless and Coolerless Components for low Power Optical Networks) and the UGent special research fund. The C3PO project aimed to develop a new generation of green Si-photonic compatible components with record low power consumption, that can enable bandwidth growth and constrain the total cost. C3PO envisioned building high-capacity access networks employing reflective photonic components. To achieve this, cost-competitive reflective transmitters based on electroabsorption modulators (EAM) needed to be closely integrated into arrays. A multi-wavelength optical source provides the required wavelength channels for both downstream and upstream signals in the WDM-PON. Chapter 1 gives a short overview of a PON and describes the main implementations of a WDM-PON access network. It introduces integrated low power transmitter arrays for a cost-effective architecture of WDM-PONs and inter-data center communication. Chapter 2 compares different optical transmitters and gives a short overview of their most important characteristics. External modulation through both Mach-Zehnder modulators (MZMs) and EAMs is described. It shows that EAMs are the best choice for low power transmitter array integration, thanks to their lower drive voltage and smaller form factor, compared to MZMs. To achieve a reduced consumption, the electronic modulator driver topology is studied in chapter 3. The challenge in designing modulator drivers is the need to deliver very large currents in combination with high voltage swings. Four distinct output configurations are compared and techniques to reduce the power consumption of the drivers are described. Chapter 5 presents duobinary (DB), a modulation scheme that is gaining interest in today’s optical transmission. As the required bandwidth is about half that of NRZ, it softens the constraints on the transmitter bandwidth. Thanks to its narrow optical spectrum, it has an improved tolerance to dispersion in long haul single mode links and it can improve the spectral efficiency in WDM architectures. For optical DB a precoder is necessary to assure the received signal is equal to the original binary signal. The conducted research that resulted in this dissertation produced 2 low power EAM driver arrays: A 10-channel 113 Gb/s modulator driver array with state-of-the art ultra-low power consumption. A 2-channel 56 Gb/s duobinary driver array with a differential output with low power consumption. Both designs are elaborately analyzed in chapter 4 and 6 respectively. To the best of our knowledge the 10-channel EAM driver array is the first in its kind, while achieving the lowest power consumption for an EAM driver so far reported, 50% below the state of the art in power consumption. The 2-channel EAM driver array is the fastest modulator driver including on-chip duobinary encoding and precoding reported so far. The final chapter provides an overview of the foremost conclusions from the presented research. It is concluded with suggestions for further research

Digital Background Self-Calibration Technique for Compensating Transition Offsets in Reference-less Flash ADCs

This Dissertation focusses on proving that background calibration using adaptive algorithms are low-cost, stable and effective methods for obtaining high accuracy in flash A/D converters. An integrated reference-less 3-bit flash ADC circuit has been successfully designed and taped out in UMC 180 nm CMOS technology in order to prove the efficiency of our proposed background calibration. References for ADC transitions have been virtually implemented built-in in the comparators dynamic-latch topology by a controlled mismatch added to each comparator input front-end. An external very simple DAC block (calibration bank) allows control the quantity of mismatch added in each comparator front-end and, therefore, compensate the offset of its effective transition with respect to the nominal value. In order to assist to the estimation of the offset of the prototype comparators, an auxiliary A/D converter with higher resolution and lower conversion speed than the flash ADC is used: a 6-bit capacitive-DAC SAR type. Special care in synchronization of analogue sampling instant in both ADCs has been taken into account. In this thesis, a criterion to identify the optimum parameters of the flash ADC design with adaptive background calibration has been set. With this criterion, the best choice for dynamic latch architecture, calibration bank resolution and flash ADC resolution are selected. The performance of the calibration algorithm have been tested, providing great programmability to the digital processor that implements the algorithm, allowing to choose the algorithm limits, accuracy and quantization errors in the arithmetic. Further, systematic controlled offset can be forced in the comparators of the flash ADC in order to have a more exhaustive test of calibration

Substrate noise analysis and techniques for mitigation in mixed-signal RF systems

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2005.This electronic version was submitted by the student author. The certified thesis is available in the Institute Archives and Special Collections.Includes bibliographical references (p. 151-158).Mixed-signal circuit design has historically been a challenge for several reasons. Parasitic interactions between analog and digital systems on a single die are one such challenge. Switching transients induced by digital circuits inject noise into the common substrate creating substrate noise. Analog circuits lack the large noise margins of digital circuits, thus making them susceptible to substrate voltage variations. This problem is exacerbated at higher frequencies as the effectiveness of standard isolation technique diminishes considerably. Historically, substrate noise was not a problem because each system was fabricated in its own package shielding it from such interactions. The work in this thesis spans all areas of substrate noise: generation, propagation, and reception. A set of guidelines in designing isolation structures was developed to assist designers in optimizing these structures for a particular application. Furthermore, the effect of substrate noise on two key components of the RF front end, the voltage controlled oscillator (VCO) and the low noise amplifier (LNA), was analyzed. Finally, a CAD tool (SNAT) was developed to efficiently simulate large digital designs to determine substrate noise performance.(cont.) Existing techniques have prohibitively long simulation times and are only suitable for final verification. Determination of substrate noise coupling during the design phase would be extremely beneficial to circuit designers who can incorporate the effect of the noise and re-design accordingly before fabrication. This would reduce the turn around time for circuits and prevent costly redesign. SNAT can be used at any stage of the design cycle to accurately predict (less than 12% error when compared to measurements) the substrate noise performance of any digital circuit with a large degree of computational efficiency.by Nisha Checka.Ph.D