Dynamic Voltage Scaling Aware Delay Fault Testing

The application of Dynamic Voltage Scaling (DVS) to reduce energy consumption may have a detrimental impact on the quality of manufacturing tests employed to detect permanent faults. This paper analyses the influence of different voltage/frequency settings on fault detection within a DVS application. In particular, the effect of supply voltage on different types of delay faults is considered. This paper presents a study of these problems with simulation results. We have demonstrated that the test application time increases as we reduce the test voltage. We have also shown that for newer technologies we do not have to go to very low voltage levels for delay fault testing. We conclude that it is necessary to test at more than one operating voltage and that the lowest operating voltage does not necessarily give the best fault cover

Acceleration of Seed Ordering and Selection for High Quality Delay Test

Seed ordering and selection is a key technique to provide high-test quality with limited resources in Built-In Self Test (BIST) environment. We present a hard-to-detect delay fault selection method to accelerate the computation time in seed ordering and selection processes. This selection method can be used to restrict faults for test generation executed in an early stage in seed ordering and selection processes, and reduce a test pattern count and therefore a computation time. We evaluate the impact of the selection method both in deterministic BIST, where one test pattern is decoded from one seed, and mixed-mode BIST, where one seed is expanded to two or more patterns. The statistical delay quality level (SDQL) is adopted as test quality measure, to represent ability to detect small delay defects (SDDs). Experimental results show that our proposed method can significantly reduce computation time from 28% to 63% and base set seed counts from 21% to 67% while slightly sacrificing test quality

Acceleration of Seed Ordering and Selection For High Quality VLSI Delay Test

Seed ordering and selection is a key technique to provide high-test quality with limited resources in Built-In Self Test (BIST) environment. We present a hard-to-detect delay fault selection method to optimize the computation time in seed ordering and selection processes. This selection method can be used to select faults for test generation when it is impractical to target all delay faults resulting large test pattern count and long Computation time. Three types of selection categories are considered, ranged in the number of seeds it produced, which is useful when we consider computing resources, such as memory and storage. We also evaluate the impact of the selection method in mixed-mode BIST when seed are expanded to more patterns, and evaluate the statistical delay quality level (SDQL) with the original work. Experimental results show that our proposed method can significantly reduce computation time while slightly sacrificing test quality

Product assurance technology for custom LSI/VLSI electronics

The technology for obtaining custom integrated circuits from CMOS-bulk silicon foundries using a universal set of layout rules is presented. The technical efforts were guided by the requirement to develop a 3 micron CMOS test chip for the Combined Release and Radiation Effects Satellite (CRRES). This chip contains both analog and digital circuits. The development employed all the elements required to obtain custom circuits from silicon foundries, including circuit design, foundry interfacing, circuit test, and circuit qualification

Product assurance technology for procuring reliable, radiation-hard, custom LSI/VLSI electronics

Advanced measurement methods using microelectronic test chips are described. These chips are intended to be used in acquiring the data needed to qualify Application Specific Integrated Circuits (ASIC's) for space use. Efforts were focused on developing the technology for obtaining custom IC's from CMOS/bulk silicon foundries. A series of test chips were developed: a parametric test strip, a fault chip, a set of reliability chips, and the CRRES (Combined Release and Radiation Effects Satellite) chip, a test circuit for monitoring space radiation effects. The technical accomplishments of the effort include: (1) development of a fault chip that contains a set of test structures used to evaluate the density of various process-induced defects; (2) development of new test structures and testing techniques for measuring gate-oxide capacitance, gate-overlap capacitance, and propagation delay; (3) development of a set of reliability chips that are used to evaluate failure mechanisms in CMOS/bulk: interconnect and contact electromigration and time-dependent dielectric breakdown; (4) development of MOSFET parameter extraction procedures for evaluating subthreshold characteristics; (5) evaluation of test chips and test strips on the second CRRES wafer run; (6) two dedicated fabrication runs for the CRRES chip flight parts; and (7) publication of two papers: one on the split-cross bridge resistor and another on asymmetrical SRAM (static random access memory) cells for single-event upset analysis

Investigation into voltage and process variation-aware manufacturing test

Increasing integration and complexity in IC design provides challenges for manufacturing testing. This thesis studies how process and supply voltage variation influence defect behaviour to determine the impact on manufacturing test cost and quality. The focus is on logic testing of static CMOS designs with respect to two important defect types in deep submicron CMOS: resistive bridges and full opens. The first part of the thesis addresses testing for resistive bridge defects in designs with multiple supply voltage settings. To enable analysis, a fault simulator is developed using a supply voltage-aware model for bridge defect behaviour. The analysis shows that for high defect coverage it is necessary to perform test for more than one supply voltage setting, due to supply voltage-dependent behaviour. A low-cost and effective test method is presented consisting of multi-voltage test generation that achieves high defect coverage and test set size reduction without compromise to defect coverage. Experiments on synthesised benchmarks with realistic bridge locations validate the proposed method.The second part focuses on the behaviour of full open defects under supply voltage variation. The aim is to determine the appropriate value of supply voltage to use when testing. Two models are considered for the behaviour of full open defects with and without gate tunnelling leakage influence. Analysis of the supply voltage-dependent behaviour of full open defects is performed to determine if it is required to test using more than one supply voltage to detect all full open defects. Experiments on synthesised benchmarks using an extended version of the fault simulator tool mentioned above, measure the quantitative impact of supply voltage variation on defect coverage.The final part studies the impact of process variation on the behaviour of bridge defects. Detailed analysis using synthesised ISCAS benchmarks and realistic bridge model shows that process variation leads to additional faults. If process variation is not considered in test generation, the test will fail to detect some of these faults, which leads to test escapes. A novel metric to quantify the impact of process variation on test quality is employed in the development of a new test generation tool, which achieves high bridge defect coverage. The method achieves a user-specified test quality with test sets which are smaller than test sets generated without consideration of process variation

Recent Trends and Perspectives on Defect-Oriented Testing

Electronics employed in modern safety-critical systems require severe qualification during the manufacturing process and in the field, to prevent fault effects from manifesting themselves as critical failures during mission operations. Traditional fault models are not sufficient anymore to guarantee the required quality levels for chips utilized in mission-critical applications. The research community and industry have been investigating new test approaches such as device-aware test, cell-aware test, path-delay test, and even test methodologies based on the analysis of manufacturing data to move the scope from OPPM to OPPB. This special session presents four contributions, from academic researchers and industry professionals, to enable better chip quality. We present results on various activities towards this objective, including device-aware test, software-based self-test, and memory test

Improving timing verification and delay testing methodologies for IC designs

textThe task of ensuring the correct temporal behavior of IC designs, both before and after fabrication, is extremely important. It is becoming even more imperative as the demand for performance increases and process technology advances into the deep sub-micron region. This dissertation tackles the key issues in the timing verification and delay testing methodologies. An efficient methodology is presented to identify false timing paths in the timing verification methodology which utilizes ATPG technique and timing information from an ordered list of timing paths according to the delay information. This dissertation also presents a speed binning methodology which utilizes structural delay tests successfully instead of functional tests. In addition, it establishes a methodology which quantifies the correlation between the timing verification prediction and actual silicon measurement of timing paths. This quantification methodology lays the foundation for further research to study the impact of deep submicron effects on design performanceElectrical and Computer Engineerin

A design for testability study on a high performance automatic gain control circuit.

A comprehensive testability study on a commercial automatic gain control circuit is presented which aims to identify design for testability (DfT) modifications to both reduce production test cost and improve test quality. A fault simulation strategy based on layout extracted faults has been used to support the study. The paper proposes a number of DfT modifications at the layout, schematic and system levels together with testability. Guidelines that may well have generic applicability. Proposals for using the modifications to achieve partial self test are made and estimates of achieved fault coverage and quality levels presente

VLSI Testing and Test Power

This paper first reviews the basics of VLSI testing, focusing on test generation and design for testability. Then it discusses the impact of test power in scan testing, and highlights the need for low-power VLSI testing.2011 International Green Computing Conference and Workshops (IGCC 2011), July 25-28, 2011, Orlando, FL, US