Ultra-low power mixed-signal frontend for wearable EEGs

Electronics circuits are ubiquitous in daily life, aided by advancements in the chip design industry, leading to miniaturised solutions for typical day to day problems. One of the critical healthcare areas helped by this advancement in technology is electroencephalography (EEG). EEG is a non-invasive method of tracking a person's brain waves, and a crucial tool in several healthcare contexts, including epilepsy and sleep disorders. Current ambulatory EEG systems still suffer from limitations that affect their usability. Furthermore, many patients admitted to emergency departments (ED) for a neurological disorder like altered mental status or seizures, would remain undiagnosed hours to days after admission, which leads to an elevated rate of death compared to other conditions. Conducting a thorough EEG monitoring in early-stage could prevent further damage to the brain and avoid high mortality. But lack of portability and ease of access results in a long wait time for the prescribed patients. All real signals are analogue in nature, including brainwaves sensed by EEG systems. For converting the EEG signal into digital for further processing, a truly wearable EEG has to have an analogue mixed-signal front-end (AFE). This research aims to define the specifications for building a custom AFE for the EEG recording and use that to review the suitability of the architectures available in the literature. Another critical task is to provide new architectures that can meet the developed specifications for EEG monitoring and can be used in epilepsy diagnosis, sleep monitoring, drowsiness detection and depression study. The thesis starts with a preview on EEG technology and available methods of brainwaves recording. It further expands to design requirements for the AFE, with a discussion about critical issues that need resolving. Three new continuous-time capacitive feedback chopped amplifier designs are proposed. A novel calibration loop for setting the accurate value for a pseudo-resistor, which is a crucial block in the proposed topology, is also discussed. This pseudoresistor calibration loop achieved the resistor variation of under 8.25%. The thesis also presents a new design of a curvature corrected bandgap, as well as a novel DDA based fourth-order Sallen-Key filter. A modified sensor frontend architecture is then proposed, along with a detailed analysis of its implementation. Measurement results of the AFE are finally presented. The AFE consumed a total power of 3.2A (including ADC, amplifier, filter, and current generation circuitry) with the overall integrated input-referred noise of 0.87V-rms in the frequency band of 0.5-50Hz. Measurement results confirmed that only the proposed AFE achieved all defined specifications for the wearable EEG system with the smallest power consumption than state-of-art architectures that meet few but not all specifications. The AFE also achieved a CMRR of 131.62dB, which is higher than any studied architectures.Open Acces

Analysis of fluctuations in semiconductor devices

The random nature of ion implantation and diffusion processes as well as inevitable tolerances in fabrication result in random fluctuations of doping concentrations and oxide thickness in semiconductor devices. These fluctuations are especially pronounced in ultrasmall (nanoscale) semiconductor devices when the spatial scale of doping and oxide thickness variations become comparable with the geometric dimensions of devices. In the disseration, the effects of these fluctuations on device characteristics are analyzed by using a new technique for the analysis of random doping and oxide thickness induced fluctuations. This technique is universal in nature in the sense that it is applicable to any transport model (drift-diffusion, semiclassical transport, quantum transport etc.) and it can be naturally extended to take into account random fluctuations of the oxide (trapped) charges and channel length. The technique is based on linearization of the transport equations with respect to the fluctuating quantities. It is computationally much (a few orders of magnitude) more efficient than the traditional Monte-Carlo approach and it yields information on the sensitivity of fluctuations of parameters of interest (e.g. threshold voltage, small-signal parameters, cut-off frequencies, etc.) to the locations of doping and oxide thickness fluctuations. For this reason, it can be very instrumental in the design of fluctuation-resistant structures of semiconductor devices. Quantum mechanical effects are taken into account by using the density-gradient model as well as through self-consistent Poisson-Schrödinger computations. Special attention is paid to the presenting of the technique in a form that is suitable for implementation on commercial device simulators. The numerical implementation of the technique is discussed in detail and numerous computational results are presented and compared with those previously published in literature

Advances in Solid State Circuit Technologies

This book brings together contributions from experts in the fields to describe the current status of important topics in solid-state circuit technologies. It consists of 20 chapters which are grouped under the following categories: general information, circuits and devices, materials, and characterization techniques. These chapters have been written by renowned experts in the respective fields making this book valuable to the integrated circuits and materials science communities. It is intended for a diverse readership including electrical engineers and material scientists in the industry and academic institutions. Readers will be able to familiarize themselves with the latest technologies in the various fields

Disseny microelectrnic de circuits discriminadors de polsos pel detector LHCb

The aim of this thesis is to present a solution for implementing the front end system of the Scintillator Pad Detector (SPD) of the calorimeter system of the LHCb experiment that will start in 2008 at the Large Hadron Collider (LHC) at CERN. The requirements of this specific system are discussed and an integrated solution is presented, both at system and circuit level. We also report some methodological achievements. In first place, a method to study the PSRR (and any transfer function) in fully differential circuits taking into account the effect of parameter mismatch is proposed. Concerning noise analysis, a method to study time variant circuits in the frequency domain is presented and justified. This would open the possibility to study the effect of 1/f noise in time variants circuits. In addition, it will be shown that the architecture developed for this system is a general solution for front ends in high luminosity experiments that must be operated with no dead time and must be robust against ballistic deficit

A Parallel Programmer for Non-Volatile Analog Memory Arrays

Since their introduction in 1967, floating-gate transistors have enjoyed widespread success as non-volatile digital memory elements in EEPROM and flash memory. In recent decades, however, a renewed interest in floating-gate transistors has focused on their viability as non-volatile analog memory, as well as programmable voltage and current sources. They have been used extensively in this capacity to solve traditional problems associated with analog circuit design, such as to correct for fabrication mismatch, to reduce comparator offset, and for amplifier auto-zeroing. They have also been used to implement adaptive circuits, learning systems, and reconfigurable systems. Despite these applications, their proliferation has been limited by complex programming procedures, which typically require high-precision test equipment and intimate knowledge of the programmer circuit to perform.;This work strives to alleviate this limitation by presenting an improved method for fast and accurate programming of floating-gate transistors. This novel programming circuit uses a digital-to-analog converter and an array of sample-and-hold circuits to facilitate fast parallel programming of floating-gate memory arrays and eliminate the need for high accuracy voltage sources. Additionally, this circuit employs a serial peripheral interface which digitizes control of the programmer, simplifying the programming procedure and enabling the implementation of software applications that obscure programming complexity from the end user. The efficient and simple parallel programming system was fabricated in a 0.5?m standard CMOS process and will be used to demonstrate the effectiveness of this new method

Third International Symposium on Magnetic Suspension Technology

In order to examine the state of technology of all areas of magnetic suspension and to review recent developments in sensors, controls, superconducting magnet technology, and design/implementation practices, the Third International Symposium on Magnetic Suspension Technology was held at the Holiday Inn Capital Plaza in Tallahassee, Florida on 13-15 Dec. 1995. The symposium included 19 sessions in which a total of 55 papers were presented. The technical sessions covered the areas of bearings, superconductivity, vibration isolation, maglev, controls, space applications, general applications, bearing/actuator design, modeling, precision applications, electromagnetic launch and hypersonic maglev, applications of superconductivity, and sensors

Solid State Circuits Technologies

The evolution of solid-state circuit technology has a long history within a relatively short period of time. This technology has lead to the modern information society that connects us and tools, a large market, and many types of products and applications. The solid-state circuit technology continuously evolves via breakthroughs and improvements every year. This book is devoted to review and present novel approaches for some of the main issues involved in this exciting and vigorous technology. The book is composed of 22 chapters, written by authors coming from 30 different institutions located in 12 different countries throughout the Americas, Asia and Europe. Thus, reflecting the wide international contribution to the book. The broad range of subjects presented in the book offers a general overview of the main issues in modern solid-state circuit technology. Furthermore, the book offers an in depth analysis on specific subjects for specialists. We believe the book is of great scientific and educational value for many readers. I am profoundly indebted to the support provided by all of those involved in the work. First and foremost I would like to acknowledge and thank the authors who worked hard and generously agreed to share their results and knowledge. Second I would like to express my gratitude to the Intech team that invited me to edit the book and give me their full support and a fruitful experience while working together to combine this book

Development of Carbon Nanotube Field-Effect Transistor Arrays for Detection of HER2 Overexpression in Breast Cancer

We developed a carbon nanotube biosensor platform that was deployed at the National Cancer Institute and successfully detected the HER2 oncogene in real cancer cells at clinically relevant levels. HER2 is a receptor protein that resides on the surface of certain cancer cells and is associated with higher aggressiveness in breast cancers. Overabundance of HER2 at the chromosomal, cell surface, and intermediate gene expression levels can all indicate a dangerous HER2 status. At the present, testing for HER2 status requires labor-intensive laboratory procedures using expensive reagents. Cost remains the major barrier to widespread screening. We propose an integrated electronic testing platform based on direct label-free gene detection. The system would integrate the various labor-intensive processes that are usually performed by skilled laboratory technicians. The heart of the system is an array of carbon nanotube field-effect transistors that can detect unlabelled nucleic acids via their intrinsic electric charges. We developed a scalable fabrication technique for carbon nanotube biosensor arrays, hardware and software for data acquisition and analysis, theoretical models for detection mechanism, and protocols for immobilization of peptide nucleic acid probes and hybridization of nucleic acids extracted from cells. We demonstrated detection of HER2 from real cell lines which express cancer genes, thereby lowering the technological barrier towards commercialization of a low-cost gene expression biosensor. The system is suitable for lab-on-a-chip integration, which could bring rapid, low-cost cancer diagnoses into the clinical setting