Ultra-low Power FinFET SRAM Cell with improved stability suitable for low power applications

In this paper, a new 11T SRAM cell using FinFET technology has been proposed, the basic component of the cell is the 6T SRAM cell with 4 NMOS access transistors to improve the stability and also makes it a dual port memory cell. The proposed cell uses a header scheme in which one extra PMOS transistor is used which is biased at different voltages to improve the read and write stability thus, helps in reducing the leakage power and active power. The cell shows improvement in RSNM (Read Static Noise Margin) with LP8T by 2.39x at sub-threshold voltage 2.68x with D6T SRAM cell, 5.5x with TG8T. The WSNM (Write Static Noise Margin) and HM (Hold Margin) of the SRAM cell at 0.9V is 306mV and 384mV. At sub-threshold operation also it shows improvement. The Leakage power reduced by 0.125x with LP8T, 0.022x with D6T SRAM cell, TG8T and SE8T. Also, impact of process variation on cell stability is discussed

A Process Variation Tolerant Self-Compensation Sense Amplifier Design

As we move under the aegis of the Moore\u27s law, we have to deal with its darker side with problems like leakage and short channel effects. Once we go beyond 45nm regime process variations also have emerged as a significant design concern.Embedded memories uses sense amplifier for fast sensing and typically, sense amplifiers uses pair of matched transistors in a positive feedback environment. A small difference in voltage level of applied input signals to these matched transistors is amplified and the resulting logic signals are latched. Intra die variation causes mismatch between the sense transistors that should ideally be identical structures. Yield loss due to device and process variations has never been so critical to cause failure in circuits. Due to growth in size of embedded SRAMs as well as usage of sense amplifier based signaling techniques, process variations in sense amplifiers leads to significant loss of yield for that we need to come up with process variation tolerant circuit styles and new devices. In this work impact of transistor mismatch due to process variations on sense amplifier is evaluated and this problem is stated. For the solution of the problem a novel self compensation scheme on sense amplifiers is presented on different technology nodes up to 32nm on conventional bulk MOSFET technology. Our results show that the self compensation technique in the conventional bulk MOSFET latch type sense amplifier not just gives improvement in the yield but also leads to improvement in performance for latch type sense amplifiers. Lithography related CD variations, fluctuations in dopant density, oxide thickness and parametric variations of devices are identified as a major challenge to the classical bulk type MOSFET. With the emerging nanoscale devices, SIA roadmap identifies FinFETs as a candidate for post-planar end-of-roadmap CMOS device. With current technology scaling issues and with conventional bulk type MOSFET on 32nm node our technique can easily be applied to Double Gate devices. In this work, we also develop the model of Double Gate MOSFET through 3D Device Simulator Damocles and TCAD simulator. We propose a FinFET based process variation tolerant sense amplifier design that exploits the back gate of FinFET devices for dynamic compensation against process variations. Results from statistical simulation show that the proposed dynamic compensation is highly effective in restoring yield at a level comparable to that of sense amplifiers without process variations. We created the 32nm double gate models generated from Damocles 3-D device simulations [25] and Taurus Device Simulator available commercially from Synopsys [47] and use them in the nominal latch type sense amplifier design and on the Independent Gate Self Compensation Sense Amplifier Design (IGSSA) to compare the yield and performance benefits of sense amplifier design on FinFET technology over the conventional bulk type CMOS based sense amplifier on 32nm technology node effective in restoring yield at a level comparable to that of sense amplifiers without process variations. We created the 32nm double gate models generated from Damocles 3-D device simulations [25] and Taurus Device Simulator available commercially from Synopsys [47] and use them in the nominal latch type sense amplifier design and on the Independent Gate Self Compensation Sense Amplifier Design (IGSSA) to compare the yield and performance benefits of sense amplifier design on FinFET technology over the conventional bulk type CMOS based sense amplifier on 32nm technology node

Ultra-low Power FinFET SRAM Cell with improved stability suitable for low power applications

In this paper, a new 11T SRAM cell using FinFET technology has been proposed, the basic component of the cell is the 6T SRAM cell with 4 NMOS access transistors to improve the stability and also makes it a dual port memory cell. The proposed cell uses a header scheme in which one extra PMOS transistor is used which is biased at different voltages to improve the read and write stability thus, helps in reducing the leakage power and active power. The cell shows improvement in RSNM (Read Static Noise Margin) with LP8T by 2.39x at sub-threshold voltage 2.68x with D6T SRAM cell, 5.5x with TG8T. The WSNM (Write Static Noise Margin) and HM (Hold Margin) of the SRAM cell at 0.9V is 306mV and 384mV. At sub-threshold operation also it shows improvement. The Leakage power reduced by 0.125x with LP8T, 0.022x with D6T SRAM cell, TG8T and SE8T. Also, impact of process variation on cell stability is discussed

Static random-access memory designs based on different FinFET at lower technology node (7nm)

Title from PDF of title page viewed January 15, 2020Thesis advisor: Masud H ChowdhuryVitaIncludes bibliographical references (page 50-57)Thesis (M.S.)--School of Computing and Engineering. University of Missouri--Kansas City, 2019The Static Random-Access Memory (SRAM) has a significant performance impact on current nanoelectronics systems. To improve SRAM efficiency, it is important to utilize emerging technologies to overcome short-channel effects (SCE) of conventional CMOS. FinFET devices are promising emerging devices that can be utilized to improve the performance of SRAM designs at lower technology nodes. In this thesis, I present detail analysis of SRAM cells using different types of FinFET devices at 7nm technology. From the analysis, it can be concluded that the performance of both 6T and 8T SRAM designs are improved. 6T SRAM achieves a 44.97% improvement in the read energy compared to 8T SRAM. However, 6T SRAM write energy degraded by 3.16% compared to 8T SRAM. Read stability and write ability of SRAM cells are determined using Static Noise Margin and N- curve methods. Moreover, Monte Carlo simulations are performed on the SRAM cells to evaluate process variations. Simulations were done in HSPICE using 7nm Asymmetrical Underlap FinFET technology. The quasiplanar FinFET structure gained considerable attention because of the ease of the fabrication process [1] – [4]. Scaling of technology have degraded the performance of CMOS designs because of the short channel effects (SCEs) [5], [6]. Therefore, there has been upsurge in demand for FinFET devices for emerging market segments including artificial intelligence and cloud computing (AI) [8], [9], Internet of Things (IoT) [10] – [13] and biomedical [17] –[18] which have their own exclusive style of design. In recent years, many Underlapped FinFET devices were proposed to have better control of the SCEs in the sub-nanometer technologies [3], [4], [19] – [33]. Underlap on either side of the gate increases effective channel length as seen by the charge carriers. Consequently, the source-to-drain tunneling probability is improved. Moreover, edge direct tunneling leakage components can be reduced by controlling the electric field at the gate-drain junction . There is a limitation on the extent of underlap on drain or source sides because the ION is lower for larger underlap. Additionally, FinFET based designs have major width quantization issue. The width of a FinFET device increases only in quanta of silicon fin height (HFIN) [4]. The width quantization issue becomes critical for ratioed designs like SRAMs, where proper sizing of the transistors is essential for fault-free operation. FinFETs based on Design/Technology Co-Optimization (DTCO_F) approach can overcome these issues [38]. DTCO_F follows special design rules, which provides the specifications for the standard SRAM cells with special spacing rules and low leakages. The performances of 6T SRAM designs implemented by different FinFET devices are compared for different pull-up, pull down and pass gate transistor (PU: PD:PG) ratios to identify the best FinFET device for high speed and low power SRAM applications. Underlapped FinFETs (UF) and Design/Technology Co-Optimized FinFETs (DTCO_F) are used for the design and analysis. It is observed that with the PU: PD:PG ratios of 1:1:1 and 1:5:2 for the UF-SRAMs the read energy has degraded by 3.31% and 48.72% compared to the DTCO_F-SRAMs, respectively. However, the read energy with 2:5:2 ratio has improved by 32.71% in the UF-SRAM compared to the DTCO_F-SRAMs. The write energy with 1:1:1 configuration has improved by 642.27% in the UF-SRAM compared to the DTCO_F-SRAM. On the other hand, the write energy with 1:5:2 and 2:5:2 configurations have degraded by 86.26% and 96% in the UF-SRAMs compared to the DTCO_F-SRAMs. The stability and reliability of different SRAMs are also evaluated for 500mV supply. From the analysis, it can be concluded that Asymmetrical Underlapped FinFET is better for high-speed applications and DTCO FinFET for low power applications.Introduction -- Next generation high performance device: FinFET -- FinFET based SRAM bitcell designs -- Benchmarking of UF-SRAMs and DTCO-F-SRAMS -- Collaborative project -- Internship experience at INTEL and Marvell Semiconductor -- Conclusion and future wor

Design, Modeling and Analysis of Non-classical Field Effect Transistors

Transistor scaling following per Moore\u27s Law slows down its pace when entering into nanometer regime where short channel effects (SCEs), including threshold voltage fluctuation, increased leakage current and mobility degradation, become pronounced in the traditional planar silicon MOSFET. In addition, as the demand of diversified functionalities rises, conventional silicon technologies cannot satisfy all non-digital applications requirements because of restrictions that stem from the fundamental material properties. Therefore, novel device materials and structures are desirable to fuel further evolution of semiconductor technologies. In this dissertation, I have proposed innovative device structures and addressed design considerations of those non-classical field effect transistors for digital, analog/RF and power applications with projected benefits. Considering device process difficulties and the dramatic fabrication cost, application-oriented device design and optimization are performed through device physics analysis and TCAD modeling methodology to develop design guidelines utilizing transistor\u27s improved characteristics toward application-specific circuit performance enhancement. Results support proposed device design methodologies that will allow development of novel transistors capable of overcoming limitation of planar nanoscale MOSFETs. In this work, both silicon and III-V compound devices are designed, optimized and characterized for digital and non-digital applications through calibrated 2-D and 3-D TCAD simulation. For digital functionalities, silicon and InGaAs MOSFETs have been investigated. Optimized 3-D silicon-on-insulator (SOI) and body-on-insulator (BOI) FinFETs are simulated to demonstrate their impact on the performance of volatile memory SRAM module with consideration of self-heating effects. Comprehensive simulation results suggest that the current drivability degradation due to increased device temperature is modest for both devices and corresponding digital circuits. However, SOI FinFET is recommended for the design of low voltage operation digital modules because of its faster AC response and better SCEs management than the BOI structure. The FinFET concept is also applied to the non-volatile memory cell at 22 nm technology node for low voltage operation with suppressed SCEs. In addition to the silicon technology, our TCAD estimation based on upper projections show that the InGaAs FinFET, with superior mobility and improved interface conditions, achieve tremendous drive current boost and aggressively suppressed SCEs and thereby a strong contender for low-power high-performance applications over the silicon counterpart. For non-digital functionalities, multi-fin FETs and GaN HEMT have been studied. Mixed-mode simulations along with developed optimization guidelines establish the realistic application potential of underlap design of silicon multi-Fin FETs for analog/RF operation. The device with underlap design shows compromised current drivability but improve analog intrinsic gain and high frequency performance. To investigate the potential of the novel N-polar GaN material, for the first time, I have provided calibrated TCAD modeling of E-mode N-polar GaN single-channel HEMT. In this work, I have also proposed a novel E-mode dual-channel hybrid MIS-HEMT showing greatly enhanced current carrying capability. The impact of GaN layer scaling has been investigated through extensive TCAD simulations and demonstrated techniques for device optimization

Sub-10nm Transistors for Low Power Computing: Tunnel FETs and Negative Capacitance FETs

One of the major roadblocks in the continued scaling of standard CMOS technology is its alarmingly high leakage power consumption. Although circuit and system level methods can be employed to reduce power, the fundamental limit in the overall energy efficiency of a system is still rooted in the MOSFET operating principle: an injection of thermally distributed carriers, which does not allow subthreshold swing (SS) lower than 60mV/dec at room temperature. Recently, a new class of steep-slope devices like Tunnel FETs (TFETs) and Negative-Capacitance FETs (NCFETs) have garnered intense interest due to their ability to surpass the 60mV/dec limit on SS at room temperature. The focus of this research is on the simulation and design of TFETs and NCFETs for ultra-low power logic and memory applications. Using full band quantum mechanical model within the Non-Equilibrium Greens Function (NEGF) formalism, source-underlapping has been proposed as an effective technique to lower the SS in GaSb-InAs TFETs. Band-tail states, associated with heavy source doping, are shown to significantly degrade the SS in TFETs from their ideal value. To solve this problem, undoped source GaSb-InAs TFET in an i-i-n configuration is proposed. A detailed circuit-to-system level evaluation is performed to investigate the circuit level metrics of the proposed devices. To demonstrate their potential in a memory application, a 4T gain cell (GC) is proposed, which utilizes the low-leakage and enhanced drain capacitance of TFETs to realize a robust and long retention time GC embedded-DRAMs. The device/circuit/system level evaluation of proposed TFETs demonstrates their potential for low power digital applications. The second part of the thesis focuses on the design space exploration of hysteresis-free Negative Capacitance FETs (NCFETs). A cross-architecture analysis using HfZrOx ferroelectric (FE-HZO) integrated on bulk MOSFET, fully-depleted SOI-FETs, and sub-10nm FinFETs shows that FDSOI and FinFET configurations greatly benefit the NCFET performance due to their undoped body and improved gate-control which enables better capacitance matching with the ferroelectric. A low voltage NC-FinFET operating down to 0.25V is predicted using ultra-thin 3nm FE-HZO. Next, we propose one-transistor ferroelectric NOR type (Fe-NOR) non-volatile memory based on HfZrOx ferroelectric FETs (FeFETs). The enhanced drain-channel coupling in ultrashort channel FeFETs is utilized to dynamically modulate memory window of storage cells thereby resulting in simple erase-, program-and read-operations. The simulation analysis predicts sub-1V program/erase voltages in the proposed Fe-NOR memory array and therefore presents a significantly lower power alternative to conventional FeRAM and NOR flash memories

ENERGY-EFFICIENT AND SECURE HARDWARE FOR INTERNET OF THINGS (IoT) DEVICES

Internet of Things (IoT) is a network of devices that are connected through the Internet to exchange the data for intelligent applications. Though IoT devices provide several advantages to improve the quality of life, they also present challenges related to security. The security issues related to IoT devices include leakage of information through Differential Power Analysis (DPA) based side channel attacks, authentication, piracy, etc. DPA is a type of side-channel attack where the attacker monitors the power consumption of the device to guess the secret key stored in it. There are several countermeasures to overcome DPA attacks. However, most of the existing countermeasures consume high power which makes them not suitable to implement in power constraint devices. IoT devices are battery operated, hence it is important to investigate the methods to design energy-efficient and secure IoT devices not susceptible to DPA attacks. In this research, we have explored the usefulness of a novel computing platform called adiabatic logic, low-leakage FinFET devices and Magnetic Tunnel Junction (MTJ) Logic-in-Memory (LiM) architecture to design energy-efficient and DPA secure hardware. Further, we have also explored the usefulness of adiabatic logic in the design of energy-efficient and reliable Physically Unclonable Function (PUF) circuits to overcome the authentication and piracy issues in IoT devices. Adiabatic logic is a low-power circuit design technique to design energy-efficient hardware. Adiabatic logic has reduced dynamic switching energy loss due to the recycling of charge to the power clock. As the first contribution of this dissertation, we have proposed a novel DPA-resistant adiabatic logic family called Energy-Efficient Secure Positive Feedback Adiabatic Logic (EE-SPFAL). EE-SPFAL based circuits are energy-efficient compared to the conventional CMOS based design because of recycling the charge after every clock cycle. Further, EE-SPFAL based circuits consume uniform power irrespective of input data transition which makes them resilience against DPA attacks. Scaling of CMOS transistors have served the industry for more than 50 years in providing integrated circuits that are denser, and cheaper along with its high performance, and low power. However, scaling of the transistors leads to increase in leakage current. Increase in leakage current reduces the energy-efficiency of the computing circuits,and increases their vulnerability to DPA attack. Hence, it is important to investigate the crypto circuits in low leakage devices such as FinFET to make them energy-efficient and DPA resistant. In this dissertation, we have proposed a novel FinFET based Secure Adiabatic Logic (FinSAL) family. FinSAL based designs utilize the low-leakage FinFET device along with adiabatic logic principles to improve energy-efficiency along with its resistance against DPA attack. Recently, Magnetic Tunnel Junction (MTJ)/CMOS based Logic-in-Memory (LiM) circuits have been explored to design low-power non-volatile hardware. Some of the advantages of MTJ device include non-volatility, near-zero leakage power, high integration density and easy compatibility with CMOS devices. However, the differences in power consumption between the switching of MTJ devices increase the vulnerability of Differential Power Analysis (DPA) based side-channel attack. Further, the MTJ/CMOS hybrid logic circuits which require frequent switching of MTJs are not very energy-efficient due to the significant energy required to switch the MTJ devices. In the third contribution of this dissertation, we have investigated a novel approach of building cryptographic hardware in MTJ/CMOS circuits using Look-Up Table (LUT) based method where the data stored in MTJs are constant during the entire encryption/decryption operation. Currently, high supply voltage is required in both writing and sensing operations of hybrid MTJ/CMOS based LiM circuits which consumes a considerable amount of energy. In order to meet the power budget in low-power devices, it is important to investigate the novel design techniques to design ultra-low-power MTJ/CMOS circuits. In the fourth contribution of this dissertation, we have proposed a novel energy-efficient Secure MTJ/CMOS Logic (SMCL) family. The proposed SMCL logic family consumes uniform power irrespective of data transition in MTJ and more energy-efficient compared to the state-of-art MTJ/ CMOS designs by using charge sharing technique. The other important contribution of this dissertation is the design of reliable Physical Unclonable Function (PUF). Physically Unclonable Function (PUF) are circuits which are used to generate secret keys to avoid the piracy and device authentication problems. However, existing PUFs consume high power and they suffer from the problem of generating unreliable bits. This dissertation have addressed this issue in PUFs by designing a novel adiabatic logic based PUF. The time ramp voltages in adiabatic PUF is utilized to improve the reliability of the PUF along with its energy-efficiency. Reliability of the adiabatic logic based PUF proposed in this dissertation is tested through simulation based temperature variations and supply voltage variations

Ultra Low Power Digital Circuit Design for Wireless Sensor Network Applications

Ny forskning innenfor feltet trådløse sensornettverk åpner for nye og innovative produkter og løsninger. Biomedisinske anvendelser er blant områdene med størst potensial og det investeres i dag betydelige beløp for å bruke denne teknologien for å gjøre medisinsk diagnostikk mer effektiv samtidig som man åpner for fjerndiagnostikk basert på trådløse sensornoder integrert i et ”helsenett”. Målet er å forbedre tjenestekvalitet og redusere kostnader samtidig som brukerne skal oppleve forbedret livskvalitet som følge av økt trygghet og mulighet for å tilbringe mest mulig tid i eget hjem og unngå unødvendige sykehusbesøk og innleggelser. For å gjøre dette til en realitet er man avhengige av sensorelektronikk som bruker minst mulig energi slik at man oppnår tilstrekkelig batterilevetid selv med veldig små batterier. I sin avhandling ” Ultra Low power Digital Circuit Design for Wireless Sensor Network Applications” har PhD-kandidat Farshad Moradi fokusert på nye løsninger innenfor konstruksjon av energigjerrig digital kretselektronikk. Avhandlingen presenterer nye løsninger både innenfor aritmetiske og kombinatoriske kretser, samtidig som den studerer nye statiske minneelementer (SRAM) og alternative minnearkitekturer. Den ser også på utfordringene som oppstår når silisiumteknologien nedskaleres i takt med mikroprosessorutviklingen og foreslår løsninger som bidrar til å gjøre kretsløsninger mer robuste og skalerbare i forhold til denne utviklingen. De viktigste konklusjonene av arbeidet er at man ved å introdusere nye konstruksjonsteknikker både er i stand til å redusere energiforbruket samtidig som robusthet og teknologiskalerbarhet øker. Forskningen har vært utført i samarbeid med Purdue University og vært finansiert av Norges Forskningsråd gjennom FRINATprosjektet ”Micropower Sensor Interface in Nanometer CMOS Technology”