Design techniques for low-power wide-band direct digital frequency synthesizers of spread spectrum communication applications

For frequency agile communication systems, fast frequency switching in fine frequency steps with good spectral purity is crucial. Direct Digital Frequency Synthesizer (DDFS) is best suitable for these applications, but is not widely employed in wireless communication systems due to its high power consumption. In general, low power and high integration design are two challenges for mixed signal-circuits and communication systems designers. In this dissertation, new design techniques for DDFS at both architecture and circuit levels are proposed and investigated in order to minimize power consumption and optimize performance. A ROM-less low power wide band DDFS prototype using segmented sine wave Digital-to-Analog Converter (DAC) were designed, fabricated and tested to demonstrate the new design techniques.;First, to further reduce power consumption and save chip area, two new phase interpolation ROM less DDFS architectures are proposed. Segmentation technique is applied to the design of sine wave DAC for DDFS: (1) based upon trigonometric identities, a segmented sine wave DAC with fine nonlinear interpolation DAC\u27s is proposed; (2) based upon first order Taylor series and simple linear interpolation, a segmented sine wave DAC with a fine linear interpolation DAC is proposed. Second, a figure of merit (FM) is defined to find the optimal sine wave DAC segmentations for various resolutions of the segmented sine wave DAC\u27s. The device mismatch effects on the performance of segmented sine wave were also discussed. Third, For DDFS using current-steering segmented sine wave DAC with 12-b phase resolution and 11-b amplitude resolution, a behavioral model in Verilog was used to verify the functionality and validate the architecture. Finally, a DDFS prototype was designed and fabricated in a standard 0.25mum CMOS process. The measured SFDR is better than 50 dB with output frequencies up to 3/8 of the 300 MHz clock frequency. The prototype occupies an active area of 1.4 mm2 and consumes 240 mW for 300 MHz clock frequency. The new techniques reduce the power dissipation and die area substantially when compared to conventional ROM based DDFS designs with on-chip DAC

Low power data converters for specific applications

Due to increasing importance of portable equipment and reduction of the supply voltage due to technology scaling, recent efforts in the design of mixed-signal circuits have focused on developing new techniques to reduce the power dissipation and supply voltage. This requires research into new architectures and circuit techniques that enable both integration and programmability. Programmability allows each component to be used for different applications, reducing the total number of components, and increased integration by eliminating external components will reduce cost and power;Since data converters are used in many different applications, in this thesis new low voltage and low power data converter techniques at both the architecture and circuit design levels are investigated to minimize power dissipation and supply voltage. To demonstrate the proposed techniques, test the performance of the proposed architectures, and verify their effectiveness in terms of power savings, five prototype chips are fabricated and tested;First, a re-configurable data converter (RDC) architecture is presented that can be programmed as analog-to-digital converter (ADC), digital-to-analog converter (DAC), or both. The reconfigurability of the RDC to different numbers of ADCs and DACs having different speeds and resolutions makes it an ideal choice for analog test bus, mixed-mode boundary scan, and built-in self test applications. It combines the advantages of both analog test buses and boundary scan techniques while the area overhead of the proposed techniques is very low compared to the mixed-mode boundary scan techniques. RDC can save power by allowing the designer to program it as the right converter for desired application. This architecture can be potentially implemented inside a field programmable gate array (FPGA) to allow the FPGA communicate with the analog world. It can also be used as a stand-alone product to give flexibility to the user to choose ADC/DAC combinations for the desired application;Next, a new method for designing low power and small area ROMless direct digital frequency synthesizers (DDFSs) is presented. In this method, a non-linear digital-to-analog converter is used to replace the phase-to-sine amplitude ROM look-up table and the linear DAC in conventional DDFS. Since the non-linear DAC converts the phase information directly into analog sine wave, no phase-to-amplitude ROM look-up table is required;Finally, a new low voltage technique based on biased inverting opamp that can have almost rail-to-rail swing with continuously valid output is discussed. Based on this biasing technique, a 10-bit segmented R-2R DAC and an 8-bit successive approximation ADC are designed and presented

Design and Implementation of an RF Front-End for Software Defined Radios

Software Defined Radios have brought a major reformation in the design standards for radios, in which a large portion of the functionality is implemented through pro­ grammable signal processing devices, giving the radio the ability to change its op­ erating parameters to accommodate new features and capabilities. A software radio approach reduces the content of radio frequency and other analog components of the traditional radios and emphasizes digital signal processing to enhance overall receiver flexibility. Field Programmable Gate Arrays (FPGA) are a suitable technology for the hardware platform as they offer the potential of hardware-like performance coupled with software-like programmability. Software defined radio is a very broad field, encompassing the design of various technologies all the way from the antenna to RF, IF, and baseband digital design. The RF section primarily consists of analog hardware modules. The IF and baseband sections are primarily digital. It is the general process of the radio to convert the incoming signal from RF to IF and then IF to baseband for better signal processing system. In this thesis, some of major building blocks of a Software defined radio are de­ signed and implemented using FPGAs. The design of a Digital front end, which provides the bridge between the baseband and analog RF portions of a wireless receiver, is synthesized. The Digital front end receiver consists of a digital down converter(DDC) which in turn comprises of a direct digital frequency synthesizer (DDFS), a phase accumulator and a low pass filter. The signal processing block of the DDFS is executed using Co-ordinate Rotation Digital Computer (CORDIC) iii Abstract algorithm. Cascaded-Integrator-Comb filters (CIC) are implemented for changing the sample rate of the incoming data. Application of a DDC includes software ra­ dios, multicarrier, multimode digital receivers, micro and pico cell systems,broadband data applications, instrumentation and test equipment and in-building wireless tele­ phony. Also, in this thesis, interfaces for connecting Texas Instruments high speed and high resolution Analog-to-Digital converters (ADC) and Digital-to-Analog converters (DAC) with Xilinx Virtex-5 FPGAs are also implemented and demonstrated

Transceiver architectures and sub-mW fast frequency-hopping synthesizers for ultra-low power WSNs

Wireless sensor networks (WSN) have the potential to become the third wireless revolution after wireless voice networks in the 80s and wireless data networks in the late 90s. This revolution will finally connect together the physical world of the human and the virtual world of the electronic devices. Though in the recent years large progress in power consumption reduction has been made in the wireless arena in order to increase the battery life, this is still not enough to achieve a wide adoption of this technology. Indeed, while nowadays consumers are used to charge batteries in laptops, mobile phones and other high-tech products, this operation becomes infeasible when scaled up to large industrial, enterprise or home networks composed of thousands of wireless nodes. Wireless sensor networks come as a new way to connect electronic equipments reducing, in this way, the costs associated with the installation and maintenance of large wired networks. To accomplish this task, it is necessary to reduce the energy consumption of the wireless node to a point where energy harvesting becomes feasible and the node energy autonomy exceeds the life time of the wireless node itself. This thesis focuses on the radio design, which is the backbone of any wireless node. A common approach to radio design for WSNs is to start from a very simple radio (like an RFID) adding more functionalities up to the point in which the power budget is reached. In this way, the robustness of the wireless link is traded off for power reducing the range of applications that can draw benefit form a WSN. In this thesis, we propose a novel approach to the radio design for WSNs. We started from a proven architecture like Bluetooth, and progressively we removed all the functionalities that are not required for WSNs. The robustness of the wireless link is guaranteed by using a fast frequency hopping spread spectrum technique while the power budget is achieved by optimizing the radio architecture and the frequency hopping synthesizer Two different radio architectures and a novel fast frequency hopping synthesizer are proposed that cover the large space of applications for WSNs. The two architectures make use of the peculiarities of each scenario and, together with a novel fast frequency hopping synthesizer, proved that spread spectrum techniques can be used also in severely power constrained scenarios like WSNs. This solution opens a new window toward a radio design, which ultimately trades off flexibility, rather than robustness, for power consumption. In this way, we broadened the range of applications for WSNs to areas in which security and reliability of the communication link are mandatory

High performance continuous-time filters for information transfer systems

Vast attention has been paid to active continuous-time filters over the years. Thus as the cheap, readily available integrated circuit OpAmps replaced their discrete circuit versions, it became feasible to consider active-RC filter circuits using large numbers of OpAmps. Similarly the development of integrated operational transconductance amplifier (OTA) led to new filter configurations. This gave rise to OTA-C filters, using only active devices and capacitors, making it more suitable for integration. The demands on filter circuits have become ever more stringent as the world of electronics and communications has advanced. In addition, the continuing increase in the operating frequencies of modern circuits and systems increases the need for active filters that can perform at these higher frequencies; an area where the LC active filter emerges. What mainly limits the performance of an analog circuit are the non-idealities of the used building blocks and the circuit architecture. This research concentrates on the design issues of high frequency continuous-time integrated filters. Several novel circuit building blocks are introduced. A novel pseudo-differential fully balanced fully symmetric CMOS OTA architecture with inherent common-mode detection is proposed. Through judicious arrangement, the common-mode feedback circuit can be economically implemented. On the level of system architectures, a novel filter low-voltage 4th order RF bandpass filter structure based on emulation of two magnetically coupled resonators is presented. A unique feature of the proposed architecture is using electric coupling to emulate the effect of the coupled-inductors, thus providing bandwidth tuning with small passband ripple. As part of a direct conversion dual-mode 802.11b/Bluetooth receiver, a BiCMOS 5th order low-pass channel selection filter is designed. The filter operated from a single 2.5V supply and achieves a 76dB of out-of-band SFDR. A digital automatic tuning system is also implemented to account for process and temperature variations. As part of a Bluetooth transmitter, a low-power quadrature direct digital frequency synthesizer (DDFS) is presented. Piecewise linear approximation is used to avoid using a ROM look-up table to store the sine values in a conventional DDFS. Significant saving in power consumption, due to the elimination of the ROM, renders the design more suitable for portable wireless communication applications

Bluetooth/WLAN receiver design methodology and IC implementations

Emerging technologies such as Bluetooth and 802.11b (Wi-Fi) have fuelled the growth of the short-range communication industry. Bluetooth, the leading WPAN (wireless personal area network) technology, was designed primarily for cable replacement applications. The first generation Bluetooth products are focused on providing low-cost radio connections among personal electronic devices. In the WLAN (wireless local area network) arena, Wi-Fi appears to be the superior product. Wi-Fi is designed for high speed internet access, with higher radio power and longer distances. Both technologies use the same 2.4GHz ISM band. The differences between Bluetooth and Wi-Fi standard features lead to a natural partitioning of applications. Nowadays, many electronics devices such as laptops and PDAs, support both Bluetooth and Wi-Fi standards to cover a wider range of applications. The cost of supporting both standards, however, is a major concern. Therefore, a dual-mode transceiver is essential to keep the size and cost of such system transceivers at a minimum. A fully integrated low-IF Bluetooth receiver is designed and implemented in a low cost, main stream 0.35um CMOS technology. The system includes the RF front end, frequency synthesizer and baseband blocks. It has -82dBm sensitivity and draws 65mA current. This project involved 6 Ph.D. students and I was in charge of the design of the channel selection complex filter is designed. In the Bluetooth transmitter, a frequency modulator with fine frequency steps is needed to generate the GFSK signal that has +/-160kHz frequency deviation. A low power ROM-less direct digital frequency synthesizer (DDFS) is designed to implement the frequency modulation. The DDFS can be used for any frequency or phase modulation communication systems that require fast frequency switching with fine frequency steps. Another contribution is the implementation of a dual-mode 802.11b/Bluetooth receiver in IBM 0.25um BiCMOS process. Direct-conversion architecture was used for both standards to achieve maximum level of integration and block sharing. I was honored to lead the efforts of 7 Ph.D. students in this project. I was responsible for system level design as well as the design of the variable gain amplifier. The receiver chip consumes 45.6/41.3mA and the sensitivity is -86/-91dBm

Transmitter architectures with digital modulators, D/A converters and switching-mode power amplifiers

This thesis is composed of nine publications and an overview of the research topic, which also summarises the work. The research described in this thesis focuses on research into the digitalisation of wireless communication base station transmitters. In particular it has three foci: digital modulation, D/A conversion and switching-mode power amplification. The main interest in the implementation of these circuits is in CMOS. The work summarizes the designs of several circuit blocks of a wireless transmitter base station. In the baseband stage, a multicarrier digital modulator that combines multiple modulated signals at different carrier frequencies digitally at baseband, and a multimode digital modulator that can be operated for three different communications standards, are implemented as integrated circuits. The digital modulators include digital power ramping and power level control units for transmission bursts. The upconversion of the baseband signal is implemented using an integrated digital quadrature modulator. The work presented provides insight into the digital-to-analogue interface in the transmitters. This interface is studied both by implementing an intermediate frequency D/A converter in BiCMOS technology and bandpass Delta-Sigma modulator-based D/A conversion in CMOS technology. Finally, the last part of the work discusses switching-mode power amplifiers which are experimented with both as discrete and integrated implementations in conjunction with 1-bit Delta-Sigma modulation and pulse-width modulation as input signal generation methods.Tämä väitöskirja koostuu yhdeksästä julkaisusta ja tutkimusaiheen yhteenvedosta. Väitöskirjassa esitetty tutkimus keskittyy langattaman viestinnän tukiasemien lähettimien digitalisoinnin tutkimukseen. Yksityiskohtaisemmin tutkimusalueet ovat: digitaalinen modulaatio, D/A muunnos ja kytkinmuotoiset tehovahvistimet. Näiden elektronisten piirien toteutuksessa keskitytään CMOS teknologiaan. Työ vetää yhteen useiden langattoman viestinnän tukiasemien lähettimien piirilohkojen suunnittelun. Kantataajuusasteella toteutetaan integroituna piirinä monikantoaaltoinen digitaalinen modulaattori, joka yhdistää useita moduloituja signaaleja eri kantoaalloilla digitaalisesti ja monistandardi digitaalinen modulaatori, joka tukee kolmea eri viestintästandardia. Digitaaliset modulaattoripiirit sisältävät digitaalisen tehoramping ja tehotason säätöyksikön lähetyspurskeita varten. Kantataajuussignaalin ylössekoitus toteutetaan integroitua digitaalista kvadratuurimodulaattoria käyttäen. Esitetty työ antaa näkemystä lähettimien digitalia-analogia rajapintaan, jota tutkitaan toteuttamalla välitaajuinen D/A muunnin BiCMOS teknologialla ja päästökaistainen Delta-Sigma-modulaattoripohjainen D/A muunnin CMOS teknologialla. Lopuksi työn viimeinen osa käsittelee kytkinmuotoisia tehovahvistimia, joita tutkitaan kokeellisesti sekä erilliskompontein toteutettuina piirein että integroiduin piirein toteutettuina käyttäen sisääntulosignaalin muodostamismenetemänä yksibittistä Delta-Sigma-modulaatiota ja pulssin leveys modulaatiota.reviewe

Design of Digital Frequency Synthesizer for 5G SDR Systems

The previous frequency synthesizer techniques for scalable SDR are not compatible with high end applications due to its complex computations and the intolerance over increased path interference rate which leads to an unsatisfied performance with improved user rate in real time environment. Designing an efficient frequency synthesizer framework in the SDR system is essential for 5G wireless communication systems with improved Quality of service (QoS). Consequently, this research has been performed based on the merits of fully digitalized frequency synthesizer and its explosion in wide range of frequency band generations. In this paper hardware optimized reconfigurable digital base band processing and frequency synthesizer model is proposed without making any design complexity trade-off to deal with the multiple standards. Here fully digitalized frequency synthesizer is introduced using simplified delay units to reduce the design complexity. Experimental results and comparative analyzes are carried out to validate the performance metrics and exhaustive test bench simulation is also carried out to verify the functionality

Architectural implementation of cordic unit and its applications

The ubiquity of DSP has made increasing demand to develop area efficient and accurate architectures in carrying out many nonlinear arithmetic operations. One such architecture is CORDIC unit which has many applications in the field of DSP including implementing transforms based on Fourier basis. This report presents architecture of CORDIC, embedded with a scaling unit that has only minimal number of adders and shifters. It can be implemented in rotation mode as well as vectoring mode. The purpose of the design is to get a scaling free CORDIC unit preserving the design of original algorithm. The proposed design has a considerable reduction in hardware when compared with other scaling free architectures. The analysis of error for different word lengths and different input ranges for fixed word length gives a better choice to choose the parameters. The error in rotation mode for 16 bit data path, obtained for Y equivalent input is 0.073% and for X equivalent input is 0.067%. We also report architecture of a DFT core that is implemented using low latency CORDIC. A scaling unit has been included to get scaled outputs. The reported DFT core architecture has 22 adders in total, in addition to 2 CORDIC units. DDS or NCO are nowadays prominently used in the applications of RF signal processing, satellite communications, etc. This report also brings out the FPGA implementation of one such DDS which has quadrature outputs. The proposed DDS design, which is based on pipelined CORDIC, has considerable improvement in terms of SFDR compared to other existing designs at reduced hardware. This report also proposes multiplier-less architecture for the implementation of radix-2^2 folded pipelined complex FFT core based on CORDIC technique. The number of points considered in the work is sixteen and the folding is done by a factor of four

Hybrid DDS-PLL based reconfigurable oscillators with high spectral purity for cognitive radio

Analytical, design and simulation studies on the performance optimization of reconfigurable architecture of a Hybrid DDS – PLL are presented in this thesis. The original contributions of this thesis are aimed towards the DDS, the dithering (spur suppression) scheme and the PLL. A new design of Taylor series-based DDS that reduces the dynamic power and number of multipliers is a significant contribution of this thesis. This thesis compares dynamic power and SFDR achieved in the design of varieties of DDS such as Quartic, Cubic, Linear and LHSC. This thesis proposes two novel schemes namely “Hartley Image Suppression” and “Adaptive Sinusoidal Interference Cancellation” overcoming the low noise floor of traditional dithering schemes. The simulation studies on a Taylor series-based DDS reveal an improvement in SFDR from 74 dB to 114 dB by using Least Mean Squares -Sinusoidal Interference Canceller (LM-SIC) with the noise floor maintained at -200 dB. Analytical formulations have been developed for a second order PLL to relate the phase noise to settling time and Phase Margin (PM) as well as to relate jitter variance and PM. New expressions relating phase noise to PM and lock time to PM are derived. This thesis derives the analytical relationship between the roots of the characteristic equation of a third order PLL and its performance metrics like PM, Gardner’s stability factor, jitter variance, spur gain and ratio of noise power to carrier power. This thesis presents an analysis to relate spur gain and capacitance ratio of a third order PLL. This thesis presents an analytical relationship between the lock time and the roots of its characteristic equation of a third order PLL. Through Vieta’s circle and Vieta’s angle, the performance metrics of a third order PLL are related to the real roots of its characteristic equation