Mobile User Connectivity in Relay-Assisted Visible Light Communications

In this paper, we investigate relay-assisted visible light communications (VLC) where a mobile user acts as a relay and forwards data from a transmitter to the end mobile user. We analyse the utilization of the amplify-and-forward (AF) and decode-and-forward (DF) relaying schemes. The focus of the paper is on analysis of the behavior of the mobile user acting as a relay while considering a realistic locations of the receivers and transmitters on a standard mobile phone, more specifically with two photodetectors on both sides of a mobile phone and a transmitting LED array located upright. We also investigate dependency of the bit error rate (BER) performance on the azimuth and elevation angles of the mobile relay device within a typical office environment. We provide a new analytical description of BER for AF and DF-based relays in VLC. In addition we compare AF and DF-based systems and show that DF offers a marginal improvement in the coverage area with a BER < 10–3 and a data rate of 100 Mb/s. Numerical results also illustrate that relay-based systems offer a significant improvement in terms of the coverage compared to direct non-line of sight VLC links

Hybrid Free-Space Optical and Visible Light Communication Link

V součastnosti bezdrátové optické komunikace (optical wireless communication, OWC) získávají širokou pozornost jako vhodný doplněk ke komunikačním přenosům v rádiovém pásmu. OWC nabízejí několik výhod včetně větší šířky přenosového pásma, neregulovaného frekvenčního pásma či odolnosti vůči elektromagnetickému rušení. Tato práce se zabývá návrhem OWC systémů pro připojení koncových uživatelů. Samotná realizace spojení může být provedena za pomoci různých variant bezdrátových technologií, například pomocí OWC, kombinací různých OWC technologií nebo hybridním rádio-optickým spojem. Za účelem propojení tzv. poslední míle je analyzován optický bezvláknový spoj (free space optics, FSO). Tato práce se dále zabývá analýzou přenosových vlastností celo-optického více skokového spoje s důrazem na vliv atmosférických podmínek. V dnešní době mnoho uživatelů tráví čas ve vnitřních prostorech kanceláří či doma, kde komunikace ve viditelném spektru (visible light communication, VLC) poskytuje lepší přenosové parametry pokrytí než úzce směrové FSO. V rámci této práce byla odvozena a experimentálně ověřena závislost pro bitovou chybovost přesměrovaného (relaying) spoje ve VLC. Pro propojení poskytovatele datavých služeb s koncovým uživatelem může být výhodné zkombinovat více přenosových technologií. Proto je navržen a analyzovám systém pro překonání tzv. problému poslední míle a posledního metru kombinující hybridní FSO a VLC technologie.The field of optical wireless communications (OWC) has recently attracted significant attention as a complementary technology to radio frequency (RF). OWC systems offer several advantages including higher bandwidth, an unregulated spectrum, resistance to electromagnetic interference and a high order of reusability. The thesis focuses on the deployment and analyses of end-user interconnections using the OWC systems. Interconnection can be established by many wireless technologies, for instance, by a single OWC technology, a combination of OWC technologies, or by hybrid OWC/RF links. In order to establish last mile outdoor interconnection, a free-space optical (FSO) has to be investigated. In this thesis, the performance of all-optical multi-hop scenarios is analyzed under atmospheric conditions. However, nowadays, many end users spend much time in indoor environments where visible light communication (VLC) technology can provide better transmission parameters and, significantly, better coverage. An analytical description of bit error rate for relaying VLC schemes is derived and experimentally verified. Nonetheless, for the last mile, interconnection of a provider and end users (joint outdoor and indoor connection) can be advantageous when combining multiple technologies. Therefore, a hybrid FSO/VLC system is proposed and analyzed for the interconnection of the last mile and last meter bottleneck

A new equalizer structure for high-speed optical links based on carrierless amplitude and phase modulation

© 2020 IEEE. Spectral efficient modulation formats can enable the transmission of higher data rates than conventional on-off keying (OOK). Carrierless amplitude and phase modulation (CAP) is such an attractive modulation scheme that has been widely considered for use in different types of optical links. The scheme however can suffer from intersymbol interference (ISI) and channel crosstalk (CCI) when the frequency response of the channel is not ideal. Conventional equalizers based on feedforward (FFE) and decision feedback (DFE) equalizers are easy to implement in practice and can mitigate some of the induced ISI. However, they fail to suppress the induced CCI in the link as each channel is equalized independently. As a result, we have recently proposed the use of a new equalizer structure for use in CAP-based optical links to mitigate these transmission impairments. This new equalizer, named CAP equalizer, can be formed with conventional FFEs and DFEs with minimal additional complexity whilst providing significant performance advantages. In this paper therefore, we review the equalizer structure and report recent demonstrations of its use in short-reach optical links. We present experimental studies on a 112 Gb/s CAP-16 VCSEL-based OM4 MMF link and a 4 Gb/s CAP-16 LED-based POF link and compare the performance of the links when both a conventional FFE and DFE equalizer and the newly proposed CAP equalizer are used. The results clearly demonstrate that the CAP equalizer offers improved receiver sensitivity and enables successful data transmission over longer fibre reaches.UK EPSRC via the UP-VLC (EP/K00042X/1) and TOWS (EP/S016570/1) project

Visible light communication based system using high power LED and dicode pulse position modulation technique

In this paper a dicode pulse position modulation (DiPPM) technique has been successfully implemented for an indoor visible light communication (VLC) based system using an FPGA and a commercial high power white LED (30W). A data rate of 13 Mbps has been achieved with a bit error rate (BER) <10-11 at a free space distance of 1.2 m through a basic transceiver circuit, and 14.5 Mbps with 1.15x10-6 of BER. Furthermore, a data rate of 13 Mbps has been successfully transmitted over a distance of 1.8 m with BER of 10-5. This proves that the application of DiPPM is a viable modulation system over free space communication links

Near-capacity MIMOs using iterative detection

In this thesis, Multiple-Input Multiple-Output (MIMO) techniques designed for transmission over narrowband Rayleigh fading channels are investigated. Specifically, in order to providea diversity gain while eliminating the complexity of MIMO channel estimation, a Differential Space-Time Spreading (DSTS) scheme is designed that employs non-coherent detection. Additionally, in order to maximise the coding advantage of DSTS, it is combined with Sphere Packing (SP) modulation. The related capacity analysis shows that the DSTS-SP scheme exhibits a higher capacity than its counterpart dispensing with SP. Furthermore, in order to attain additional performance gains, the DSTS system invokes iterative detection, where the outer code is constituted by a Recursive Systematic Convolutional (RSC) code, while the inner code is a SP demapper in one of the prototype systems investigated, while the other scheme employs a Unity Rate Code (URC) as its inner code in order to eliminate the error floor exhibited by the system dispensing with URC. EXIT charts are used to analyse the convergence behaviour of the iteratively detected schemes and a novel technique is proposed for computing the maximum achievable rate of the system based on EXIT charts. Explicitly, the four-antenna-aided DSTSSP system employing no URC precoding attains a coding gain of 12 dB at a BER of 10-5 and performs within 1.82 dB from the maximum achievable rate limit. By contrast, the URC aidedprecoded system operates within 0.92 dB from the same limit.On the other hand, in order to maximise the DSTS system’s throughput, an adaptive DSTSSP scheme is proposed that exploits the advantages of differential encoding, iterative decoding as well as SP modulation. The achievable integrity and bit rate enhancements of the system are determined by the following factors: the specific MIMO configuration used for transmitting data from the four antennas, the spreading factor used and the RSC encoder’s code rate.Additionally, multi-functional MIMO techniques are designed to provide diversity gains, multiplexing gains and beamforming gains by combining the benefits of space-time codes, VBLASTand beamforming. First, a system employing Nt=4 transmit Antenna Arrays (AA) with LAA number of elements per AA and Nr=4 receive antennas is proposed, which is referred to as a Layered Steered Space-Time Code (LSSTC). Three iteratively detected near-capacity LSSTC-SP receiver structures are proposed, which differ in the number of inner iterations employed between the inner decoder and the SP demapper as well as in the choice of the outer code, which is either an RSC code or an Irregular Convolutional Code (IrCC). The three systems are capable of operating within 0.9, 0.4 and 0.6 dB from the maximum achievable rate limit of the system. A comparison between the three iteratively-detected schemes reveals that a carefully designed two-stage iterative detection scheme is capable of operating sufficiently close to capacity at a lower complexity, when compared to a three-stage system employing a RSC or a two-stage system using an IrCC as an outer code. On the other hand, in order to allow the LSSTC scheme to employ less receive antennas than transmit antennas, while still accommodating multiple users, a Layered Steered Space-Time Spreading (LSSTS) scheme is proposed that combines the benefits of space-time spreading, V-BLAST, beamforming and generalised MC DS-CDMA. Furthermore, iteratively detected LSSTS schemes are presented and an LLR post-processing technique is proposed in order to improve the attainable performance of the iteratively detected LSSTS system.Finally, a distributed turbo coding scheme is proposed that combines the benefits of turbo coding and cooperative communication, where iterative detection is employed by exchanging extrinsic information between the decoders of different single-antenna-aided users. Specifically, the effect of the errors induced in the first phase of cooperation, where the two users exchange their data, on the performance of the uplink in studied, while considering different fading channel characteristics

10 Gbps Mobile Visible Light Communication System Employing Angle Diversity, Imaging Receivers, and Relay Nodes

Over the last decade, visible light communication (VLC) systems have typically operated between 50 Mbps and 3.4 Gbps. In this paper, we propose and evaluate mobile VLC systems that operate at 10 Gbps. The enhancements in channel bandwidth and data rate are achieved by the introduction of laser diodes (LDs), angle diversity receivers (ADR), imaging receivers, relay nodes and delay adaptation techniques. We propose three mobile VLC systems; an ADR relay assisted LD-VLC (ADRR-LD), an imaging relay assisted LD-VLC (IMGR-LD) and select-the-best imaging relay assisted LD-VLC (SBIMGR-LD). The ADR and imaging receiver are proposed for the VLC system to mitigate the intersymbol interference (ISI), maximise the signal to noise ratio (SNR) and reduce the impact of multipath dispersion due to mobility. The combination of IMGR-LD with a delay adaptation technique adds a degree of freedom to the link design, which results in a VLC system that has the ability to provide high data rates under mobility. The proposed IMGR-LD system achieves significant improvements in the SNR over other systems in the worst case scenario in the considered real indoor environment

Performance Enhancement in SU and MU MIMO-OFDM Technique for Wireless Communication: A Review

The consistent demand for higher data rates and need to send giant volumes of data while not compromising the quality of communication has led the development of a new generations of wireless systems. But range and data rate limitations are there in wireless devices. In an attempt to beat these limitations, Multi Input Multi Output (MIMO) systems will be used which also increase diversity and improve the bit error rate (BER) performance of wireless systems. They additionally increase the channel capacity, increase the transmitted data rate through spatial multiplexing, and/or reduce interference from other users. MIMO systems therefore create a promising communication system because of their high transmission rates without additional bandwidth or transmit power and robustness against multipath fading. This paper provides the overview of Multiuser MIMO system. A detailed review on how to increase performance of system and reduce the bit error rate (BER) in different fading environment e.g. Rayleigh fading, Rician fading, Nakagami fading, composite fading

Design of communication systems based on broadband sources for fiber and free space optical links

[ES] Las comunicaciones ópticas inalámbricas (OWC) constituyen una tecnología muy prometedora para el desarrollo de futuras comunicaciones inalámbricas. De hecho, ha despertado un interés creciente entre los investigadores y varias empresas de todo el mundo trabajan actualmente en el desarrollo de redes inalámbricas de muy alta velocidad. Las comunidades científica e industrial consideran la OWC como una tecnología complementaria en sus diversas formas: comunicaciones ópticas en el espacio libre (FSO), comunicaciones de luz visible (VLC) o fidelidad de la luz (Li-Fi). El espectro óptico ha sido considerado durante muchos años como una gran oportunidad para las comunicaciones inalámbricas, especialmente debido a la saturación del espectro de radiofrecuencia (RF). Esta disertación trata del uso de fuentes de banda ancha en sistemas de transmisión de luz visible (VLC), así como en sistemas de transmisión en el espectro infrarrojo por fibra óptica. En el trabajo de investigación realizado se pueden distinguir tres partes: En la primera parte, se considera el estudio y la simulación de componentes de Diodos Emisores de Luz (LED) con el software WIEN2k centrándose en las propiedades ópticas y eléctricas de los elementos II-VI. La segunda parte trata del diseño, la implementación y las pruebas de diferentes prototipos de comunicación VLC para la transmisión analógica y digital en modo simplex y semidúplex. Hemos demostrado un sistema OWC empleando una fuente de banda ancha (LED) para la transmisión no sólo de datos, sino también para la transmisión inalámbrica de energía. Además, se aborda el problema de la sincronización y la detección del nivel "1" o "0" de un bit en los sistemas de comunicación inalámbrica óptica implementados que surge como consecuencia de la atenuación de la luz a lo largo de la distancia y al problema de la pérdida de línea de visión (NLOS) entre el emisor y el receptor. Para hacer frente a este problema, se ha proporcionado un protocolo de comunicación que garantiza la transmisión fiable de datos digitales con un algoritmo de detección de nivel de bits adaptativo y se ha demostrado su eficacia mediante la transmisión de textos e imágenes. Además, esta tesis aporta una solución para la implementación de transmisores multiplexados en redes con división de longitud de onda (WDM) para formatos de modulación con multiplexación por división de frecuencia ortogonal (OFDM) basados en el uso de fuentes de banda ancha en el espectro infrarrojo para redes de fibra bidireccionales centralizadas. A pesar de las limitaciones impuestas por la dispersión cromática en el uso de este tipo de fuentes ópticas, la inclusión de ciertas estructuras antes de la detección permite la transmisión de señales OFDM en enlaces ópticos. En este trabajo se ha demostrado experimentalmente la reutilización de portadoras, la asignación dinámica de ancho de banda y la transmisión de señales OFDM multibanda mediante el uso de fuentes ópticas de banda ancha en redes WDM. Los principales resultados obtenidos en cada parte de esta tesis doctoral muestran los procedimientos de estudio, la eficacia de las soluciones propuestas y las limitaciones encontradas.[CA] Les comunicacions òptiques sense fils (OWC) constitueixen una tecnologia molt prometedora per al desenvolupament de futures comunicacions sense fils. De fet, ha despertat un interés creixent entre els investigadors i diverses empreses de tot el món treballen actualment en el desenvolupament de xarxes sense fils de molt alta velocitat. Les comunitats científica i industrial consideren la OWC com una tecnologia complementària en les seues diverses formes: comunicacions òptiques en l'espai lliure (FSO), comunicacions de llum visible (VLC) o fidelitat de la llum (Li-Fi). L'espectre òptic ha sigut considerat durant molts anys com una gran oportunitat per a les comunicacions sense fils, especialment a causa de la saturació de l'espectre de radiofreqüència (RF). Aquesta dissertació tracta de l'ús de fonts de banda ampla en sistemes de transmissió de llum visible (VLC), així com en sistemes de transmissió en l'espectre infraroig per fibra òptica. En el treball de recerca realitzat es poden distingir tres parts: ¿ En la primera part, es considera l'estudi i la simulació de components de Díodes Emissors de Llum (LED) amb el software WIEN2k centrant-se en les propietats òptiques i elèctriques dels elements II-VI. ¿ La segona part tracta del disseny, la implementació i les proves de diferents prototips de comunicació VLC per a la transmissió analògica i digital de manera simplex i semidúplex. Hem demostrat un sistema OWC emprant una font de banda ampla (LED) per a la transmissió no sols de dades, sinó també per a la transmissió sense fil d'energia. A més, s'aborda el problema de la sincronització i la detecció del nivell "1" o "0" d'un bit en els sistemes de comunicació sense fil òptica implementats, que sorgeix a conseqüència de l'atenuació de la llum al llarg de la distància i al problema de la pèrdua de línia de visió (NLOS) entre l'emissor i el receptor. Per a fer front a aquest problema, s'ha proporcionat un protocol de comunicació que garanteix la transmissió fiable de dades digitals amb un algorisme de detecció de nivell de bits adaptatiu i s'ha demostrat la seua eficàcia mitjançant la transmissió de textos i imatges. ¿ A més, aquesta tesi aporta una solució per a la implementació de transmissors multiplexats en xarxes amb divisió de longitud d'ona (WDM) per a formats de modulació amb multiplexació per divisió de freqüència ortogonal (OFDM) basats en l'ús de fonts de banda ampla en l'espectre infraroig per a xarxes de fibra bidireccionals centralitzades. Malgrat les limitacions imposades per la dispersió cromàtica en l'ús d'aquest tipus de fonts òptiques, la inclusió d'unes certes estructures abans de la detecció permet la transmissió de senyals OFDM en enllaços òptics. En aquest treball s'ha demostrat experimentalment la reutilització de portadores, l'assignació dinàmica d'amplada de banda i la transmissió de senyals OFDM multibanda mitjançant l'ús de fonts òptiques de banda ampla en xarxes WDM. Els principals resultats obtinguts en cada part d'aquesta tesi doctoral mostren els procediments d'estudi, l'eficàcia de les solucions proposades i les limitacions trobades.[EN] Optical wireless communication (OWC) is a very promising technology for future wireless communications developments. It has attracted increasing interest from researchers and several companies around the world are currently working on the development of very high-speed wireless networks. The scientific and industrial communities believe that OWC will be a complementary technology in its various forms: Free Space Optical communications (FSO), Visible Light Communications (VLC), Light Fidelity (Li-Fi). In fact, the optical spectrum has been considered for many years as a great opportunity for wireless communications especially due to the saturation of the radio frequency (RF) spectrum. This dissertation deals with the use of broadband sources in visible light transmission systems (VLC) as well as fiber optic systems. To carry out the research, three parts can be distinguished: In the first part, we consider the study and simulation of Light Emitting Diode (LED) components with the WIEN2k software by focusing on the optical and electrical properties of elements II-VI. The second part deals with the design, implementation and testing of different VLC communication prototypes for analog and digital transmission in simplex and half-duplex mode. We have demonstrated that an OWC system using a broadband source (i.e. an LED) can be used not only for data transmission, but also for wireless power transmission. Moreover, the synchronization problem and the detection of level "1" or "0" of a bit often arise in the optical wireless communication systems. This is a result of the attenuation nature of the light over the distance and the problem of Non Line-Of-Sight (NLOS) between the emitter and the receiver. To deal with this problem, a communication protocol ensuring reliable digital data transmission with an adaptive bit level detection algorithm has been provided and its effectiveness has been demonstrated by the transmission of texts and images. In addition, this thesis provides a solution for the implementation of wavelength division multiplexed - orthogonal frequency division multiplexed (WDM-OFDM) transmitters based on the use of broadband sources in the infrared spectrum for centralized bidirectional fiber networks. Despite the chromatic dispersion that avoids the use of this type of optical sources, the inclusion of certain structures before detection allows the transmission of OFDM signals in optical links. Carrier reuse, dynamic bandwidth allocation and multiband OFDM signals transmission will be experimentally demonstrated by using optical broadband sources in WDM networks. The main results obtained during this thesis work demonstrate the study procedures, for each part, the effectiveness of the proposed solutions as well as the constraints encountered.Sekkiou, I. (2021). Design of communication systems based on broadband sources for fiber and free space optical links [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/172542TESI