A Polyphase Multipath Technique for Software-Defined Radio Transmitters

Transmitter circuits using large signal swings and hard-switched mixers are power-efficient, but also produce unwanted harmonics and sidebands, which are commonly removed using dedicated filters. This paper presents a polyphase multipath technique to relax or eliminate filters by canceling a multitude of harmonics and sidebands. Using this technique, a wideband and flexible power upconverter with a clean output spectrum is realized in 0.13-mum CMOS, aiming at a software-defined radio application. Prototype chips operate from DC to 2.4 GHz with spurs smaller than -40 dBc up to the 17th harmonic (18-path mode) or 5th harmonic (6-path mode) of the transmit frequency, without tuning or calibration. The transmitter delivers 8 mW of power to a 100-Omega load (2.54 Vpp-diff voltage swing) and the complete chip consumes 228 mW from a 1.2-V supply. It uses no filters, but only digital circuits and mixer

STUDY OF FULLY-INTEGRATED LOW-DROPOUT REGULATORS

Department of Electrical EngineeringThis thesis focuses on the introduction of fully-integrated low-dropout regulators (LDOs). Recently, for the mobile and internet-of-things applications, the level of integration is getting higher. LDOs get popular in integrated circuit design including functions such as reducing switching ripples from high-efficiency regulators, cancelling spurs from other loads, and giving different supply voltages to loads. In accordance with load applications, choosing proper LDOs is important. LDOs can be classified by the types of power MOSEFT, the topologies of error amplifier, and the locations of dominant pole. Analog loads such as voltage-controlled oscillators and analog-to-digital converters need LDOs that have high power-supply-rejection-ratio (PSRR), high accuracy, and low noise. Digital loads such as DRAM and CPU need fast transient response, a wide range of load current providable LDOs. As an example, we present the design procedure of a fully-integrated LDO that obtains the desired PSRR. In analog LDOs, we discuss advanced techniques such as local positive feedback loop and zero path that can improve stability and PSRR performance. In digital LDOs, the techniques to improve transient response are introduced. In analog-digital hybrid LDOs, to achieve both fast transient and high PSRR performance in a fully-integrated chip, how to optimally combine analog and digital LDOs is considered based on the characteristics of each LDO type. The future work is extracted from the considerations and limitations of conventional techniques.clos

An Analog Phase Interpolation Based Fractional-N PLL

A novel phase-locked loop topology is presented. Compared to conventional designs, this architecture aims to increase frequency resolution and reduce quantization noise while maintaining the fractional-N benefits of high bandwidth and low phase noise up-conversion. This is achieved utilizing a feedforward mechanism for offset cancellation from the integer-N frequency. The design is implemented in a 0.13μm CMOS process technology. A frequency resolution of 1.16Hz is achieved on a 5GHz differential delay cell VCO with a 100MHz reference oscillator. A ping-pong swallow counter topology alleviates pipeline latency to achieve 1-64 divide ratios. A digital pulse generator and nested phase-frequency detector provide tunable offset cancellation. A 5-bit current-steering DAC capable of 200ps pulses reduces output spurs. Theoretical calculations and Simulink modeling provides insight to the effects of non idealities in the system. Test structures and loop configurability are programmed via SPI interface through a custom GUI and prototype PCB

A Low Noise Sub-Sampling PLL in Which Divider Noise Is Eliminated and PD-CP Noise Is not multiplied by N^2

This paper presents a 2.2-GHz low jitter sub-sampling based PLL. It uses a phase-detector/charge-pump (PD/CP)that sub-samples the VCO output with the reference clock. In contrast to what happens in a classical PLL, the PD/CP noise is not multiplied by N2 in this sub-sampling PLL, resulting in a low noise contribution from the PD/CP. Moreover, no frequency divider is needed in the locked state and hence divider noise and power can be eliminated. An added frequency locked loop guarantees correct frequency locking without degenerating jitter performance when in lock. The PLL is implemented in a standard 0.18- m CMOS process. It consumes 4.2 mA from a 1.8 V supply and occupies an active area of 0.4 X 0.45 m

Techniques for Wideband All Digital Polar Transmission

abstract: Modern Communication systems are progressively moving towards all-digital transmitters (ADTs) due to their high efficiency and potentially large frequency range. While significant work has been done on individual blocks within the ADT, there are few to no full systems designs at this point in time. The goal of this work is to provide a set of multiple novel block architectures which will allow for greater cohesion between the various ADT blocks. Furthermore, the design of these architectures are expected to focus on the practicalities of system design, such as regulatory compliance, which here to date has largely been neglected by the academic community. Amongst these techniques are a novel upconverted phase modulation, polyphase harmonic cancellation, and process voltage and temperature (PVT) invariant Delta Sigma phase interpolation. It will be shown in this work that the implementation of the aforementioned architectures allows ADTs to be designed with state of the art size, power, and accuracy levels, all while maintaining PVT insensitivity. Due to the significant performance enhancement over previously published works, this work presents the first feasible ADT architecture suitable for widespread commercial deployment.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

Design of CMOS integrated frequency synthesizers for ultra-wideband wireless communications systems

Ultra¬wide band (UWB) system is a breakthrough in wireless communication, as it provides data rate one order higher than existing ones. This dissertation focuses on the design of CMOS integrated frequency synthesizer and its building blocks used in UWB system. A mixer¬based frequency synthesizer architecture is proposed to satisfy the agile frequency hopping requirement, which is no more than 9.5 ns, three orders faster than conventional phase¬locked loop (PLL)¬based synthesizers. Harmonic cancela¬tion technique is extended and applied to suppress the undesired harmonic mixing components. Simulation shows that sidebands at 2.4 GHz and 5 GHz are below 36 dBc from carrier. The frequency synthesizer contains a novel quadrature VCO based on the capacitive source degeneration structure. The QVCO tackles the jeopardous ambiguity of the oscillation frequency in conventional QVCOs. Measurement shows that the 5¬GHz CSD¬QVCO in 0.18 µm CMOS technology draws 5.2 mA current from a 1.2 V power supply. Its phase noise is ¬120 dBc at 3 MHz offset. Compared with existing phase shift LC QVCOs, the proposed CSD¬QVCO presents better phase noise and power efficiency. Finally, a novel injection locking frequency divider (ILFD) is presented. Im¬plemented with three stages in 0.18 µm CMOS technology, the ILFD draws 3¬mA current from a 1.8¬V power supply. It achieves multiple large division ratios as 6, 12, and 18 with all locking ranges greater than 1.7 GHz and injection frequency up to 11 GHz. Compared with other published ILFDs, the proposed ILFD achieves the largest division ratio with satisfactory locking range

고속 시리얼 링크를 위한 고리 발진기를 기반으로 하는 주파수 합성기

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022. 8. 정덕균.In this dissertation, major concerns in the clocking of modern serial links are discussed. As sub-rate, multi-standard architectures are becoming predominant, the conventional clocking methodology seems to necessitate innovation in terms of low-cost implementation. Frequency synthesis with active, inductor-less oscillators replacing LC counterparts are reviewed, and solutions for two major drawbacks are proposed. Each solution is verified by prototype chip design, giving a possibility that the inductor-less oscillator may become a proper candidate for future high-speed serial links. To mitigate the high flicker noise of a high-frequency ring oscillator (RO), a reference multiplication technique that effectively extends the bandwidth of the following all-digital phase-locked loop (ADPLL) is proposed. The technique avoids any jitter accumulation, generating a clean mid-frequency clock, overall achieving high jitter performance in conjunction with the ADPLL. Timing constraint for the proper reference multiplication is first analyzed to determine the calibration points that may correct the existent phase errors. The weight for each calibration point is updated by the proposed a priori probability-based least-mean-square (LMS) algorithm. To minimize the time required for the calibration, each gain for the weight update is adaptively varied by deducing a posteriori which error source dominates the others. The prototype chip is fabricated in a 40-nm CMOS technology, and its measurement results verify the low-jitter, high-frequency clock generation with fast calibration settling. The presented work achieves an rms jitter of 177/223 fs at 8/16-GHz output, consuming 12.1/17-mW power. As the second embodiment, an RO-based ADPLL with an analog technique that addresses the high supply sensitivity of the RO is presented. Unlike prior arts, the circuit for the proposed technique does not extort the RO voltage headroom, allowing high-frequency oscillation. Further, the performance given from the technique is robust over process, voltage, and temperature (PVT) variations, avoiding the use of additional calibration hardware. Lastly, a comprehensive analysis of phase noise contribution is conducted for the overall ADPLL, followed by circuit optimizations, to retain the low-jitter output. Implemented in a 40-nm CMOS technology, the frequency synthesizer achieves an rms jitter of 289 fs at 8 GHz output without any injected supply noise. Under a 20-mVrms white supply noise, the ADPLL suppresses supply-noise-induced jitter by -23.8 dB.본 논문은 현대 시리얼 링크의 클락킹에 관여되는 주요한 문제들에 대하여 기술한다. 준속도, 다중 표준 구조들이 채택되고 있는 추세에 따라, 기존의 클라킹 방법은 낮은 비용의 구현의 관점에서 새로운 혁신을 필요로 한다. LC 공진기를 대신하여 능동 소자 발진기를 사용한 주파수 합성에 대하여 알아보고, 이에 발생하는 두가지 주요 문제점과 각각에 대한 해결 방안을 탐색한다. 각 제안 방법을 프로토타입 칩을 통해 그 효용성을 검증하고, 이어서 능동 소자 발진기가 미래의 고속 시리얼 링크의 클락킹에 사용될 가능성에 대해 검토한다. 첫번째 시연으로써, 고주파 고리 발진기의 높은 플리커 잡음을 완화시키기 위해 기준 신호를 배수화하여 뒷단의 위상 고정 루프의 대역폭을 효과적으로 극대화 시키는 회로 기술을 제안한다. 본 기술은 지터를 누적 시키지 않으며 따라서 깨끗한 중간 주파수 클락을 생성시켜 위상 고정 루프와 함께 높은 성능의 고주파 클락을 합성한다. 기준 신호를 성공적으로 배수화하기 위한 타이밍 조건들을 먼저 분석하여 타이밍 오류를 제거하기 위한 방법론을 파악한다. 각 교정 중량은 연역적 확률을 기반으로한 LMS 알고리즘을 통해 갱신되도록 설계된다. 교정에 필요한 시간을 최소화 하기 위하여, 각 교정 이득은 타이밍 오류 근원들의 크기를 귀납적으로 추론한 값을 바탕으로 지속적으로 제어된다. 40-nm CMOS 공정으로 구현된 프로토타입 칩의 측정을 통해 저소음, 고주파 클락을 빠른 교정 시간안에 합성해 냄을 확인하였다. 이는 177/223 fs의 rms 지터를 가지는 8/16 GHz의 클락을 출력한다. 두번째 시연으로써, 고리 발진기의 높은 전원 노이즈 의존성을 완화시키는 기술이 포함된 주파수 합성기가 설계되었다. 이는 고리 발진기의 전압 헤드룸을 보존함으로서 고주파 발진을 가능하게 한다. 나아가, 전원 노이즈 감소 성능은 공정, 전압, 온도 변동에 대하여 민감하지 않으며, 따라서 추가적인 교정 회로를 필요로 하지 않는다. 마지막으로, 위상 노이즈에 대한 포괄적 분석과 회로 최적화를 통하여 주파수 합성기의 저잡음 출력을 방해하지 않는 방법을 고안하였다. 해당 프로토타입 칩은 40-nm CMOS 공정으로 구현되었으며, 전원 노이즈가 인가되지 않은 상태에서 289 fs의 rms 지터를 가지는 8 GHz의 클락을 출력한다. 또한, 20 mVrms의 전원 노이즈가 인가되었을 때에 유도되는 지터의 양을 -23.8 dB 만큼 줄이는 것을 확인하였다.1 Introduction 1 1.1 Motivation 3 1.1.1 Clocking in High-Speed Serial Links 4 1.1.2 Multi-Phase, High-Frequency Clock Conversion 8 1.2 Dissertation Objectives 10 2 RO-Based High-Frequency Synthesis 12 2.1 Phase-Locked Loop Fundamentals 12 2.2 Toward All-Digital Regime 15 2.3 RO Design Challenges 21 2.3.1 Oscillator Phase Noise 21 2.3.2 Challenge 1: High Flicker Noise 23 2.3.3 Challenge 2: High Supply Noise Sensitivity 26 3 Filtering RO Noise 28 3.1 Introduction 28 3.2 Proposed Reference Octupler 34 3.2.1 Delay Constraint 34 3.2.2 Phase Error Calibration 38 3.2.3 Circuit Implementation 51 3.3 IL-ADPLL Implementation 55 3.4 Measurement Results 59 3.5 Summary 63 4 RO Supply Noise Compensation 69 4.1 Introduction 69 4.2 Proposed Analog Closed Loop for Supply Noise Compensation 72 4.2.1 Circuit Implementation 73 4.2.2 Frequency-Domain Analysis 76 4.2.3 Circuit Optimization 81 4.3 ADPLL Implementation 87 4.4 Measurement Results 90 4.5 Summary 98 5 Conclusions 99 A Notes on the 8REF 102 B Notes on the ACSC 105박