Design of low-power RF energy harvester for IoT sensors

Rapid technological advancement in CMOS technologies has resulted in increased deployment of low-power Internet-of-Things (IoT) devices. As batteries, used to power-up these devices, suffer from limited lifespan, powering up numerous devices have become a major concern. Radio frequency (RF) is ubiquitous in the surroundings from which energy can be harvested and utilized to increase battery lifetime. Even for low-power sensors, RF energy harvesters can be utilized as primary power sources. However, power density of RF signals is very low and therefore building blocks of RF energy harvester need to be designed carefully to maximize efficiency to gain suitable output power. This research is focused on the design of an RF energy harvesting system in standard CMOS technology. The main goal of this research is to design an RF energy harvesting system with high power conversion efficiency (PCE) and adequate output voltage for low input power. The proposed dynamic voltage compensated cross-coupled fully differential rectifier is capable of providing very high PCE. The synchronous DC-DC boost converter provides stable DC output voltage. Rectifier and DC-DC converter of the system have been designed by using low-power transistors to ensure operation at very low input power. In order to maximize the power transfer through the system, matching network and maximum power point tracking (MPPT) controller has been implemented. In order to cope with rapid input power variation, a machine learning (ML) based MPPT controller has been designed and implemented into FPGA. The proposed ML based MPPT controller has demonstrated fast response time. To further enhance the performance of the RF energy harvesting system, a self-compensated rectifier integrated energy harvesting system is also presented. The energy extracted by using the proposed RF energy harvesting systems can easily be stored and utilized to fully power up low-power sensors used for IoT devices. Integration of RF energy harvester with these devices will significantly reduce the maintenance cost and result in energy-effluent IoT technologies.Includes bibliographical references

Power Management ICs for Internet of Things, Energy Harvesting and Biomedical Devices

This dissertation focuses on the power management unit (PMU) and integrated circuits (ICs) for the internet of things (IoT), energy harvesting and biomedical devices. Three monolithic power harvesting methods are studied for different challenges of smart nodes of IoT networks. Firstly, we propose that an impedance tuning approach is implemented with a capacitor value modulation to eliminate the quiescent power consumption. Secondly, we develop a hill-climbing MPPT mechanism that reuses and processes the information of the hysteresis controller in the time-domain and is free of power hungry analog circuits. Furthermore, the typical power-performance tradeoff of the hysteresis controller is solved by a self-triggered one-shot mechanism. Thus, the output regulation achieves high-performance and yet low-power operations as low as 12 µW. Thirdly, we introduce a reconfigurable charge pump to provide the hybrid conversion ratios (CRs) as 1⅓× up to 8× for minimizing the charge redistribution loss. The reconfigurable feature also dynamically tunes to maximum power point tracking (MPPT) with the frequency modulation, resulting in a two-dimensional MPPT. Therefore, the voltage conversion efficiency (VCE) and the power conversion efficiency (PCE) are enhanced and flattened across a wide harvesting range as 0.45 to 3 V. In a conclusion, we successfully develop an energy harvesting method for the IoT smart nodes with lower cost, smaller size, higher conversion efficiency, and better applicability. For the biomedical devices, this dissertation presents a novel cost-effective automatic resonance tracking method with maximum power transfer (MPT) for piezoelectric transducers (PT). The proposed tracking method is based on a band-pass filter (BPF) oscillator, exploiting the PT’s intrinsic resonance point through a sensing bridge. It guarantees automatic resonance tracking and maximum electrical power converted into mechanical motion regardless of process variations and environmental interferences. Thus, the proposed BPF oscillator-based scheme was designed for an ultrasonic vessel sealing and dissecting (UVSD) system. The sealing and dissecting functions were verified experimentally in chicken tissue and glycerin. Furthermore, a combined sensing scheme circuit allows multiple surgical tissue debulking, vessel sealer and dissector (VSD) technologies to operate from the same sensing scheme board. Its advantage is that a single driver controller could be used for both systems simplifying the complexity and design cost. In a conclusion, we successfully develop an ultrasonic scalpel to replace the other electrosurgical counterparts and the conventional scalpels with lower cost and better functionality

Energy efficient control for power management circuits operating from nano-watts to watts

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2013.Cataloged from PDF version of thesis.Includes bibliographical references (p. 163-172).Energy efficiency and form factor are the key driving forces in today's power electronics. All power delivery circuits, irrespective of the magnitude of power, basically consists of power trains, gate drivers and control circuits. Although the control circuits are primarily required for regulation, these circuits can play a crucial role in achieving high efficiency and/or minimizing overall system form-factor. In this thesis, power converter circuits, spanning a wide operating range- from nano-watts to watts, are presented while highlighting techniques for using digital control circuits not just for regulation but also to achieve high system efficiency and smaller system form-factor. The first part of the thesis presents a power management unit of an autonomous wireless sensor that sustains itself by harvesting energy from the endo-cochlear potential (EP), the 70-100mV electrochemical potential inside the mammalian inner ear. Due to the anatomical constraints, the total extractable power from the EP is limited to 1.1-6.3nW. A low switching frequency boost converter is employed to increase the input voltage to a higher voltage usable by CMOS circuits in the sensor. Ultra-low power digital control circuits with timers help keep the quiescent power of the power management unit down to 544pW. Further, a charge-pump is used to implement leakage reduction techniques in the sensor. This work demonstrates how digital low power control circuit design can help improve converter efficiency and ensure system sustainability. All circuits have been implemented on a 0.18[mu]m CMOS process. The second part of the thesis discusses an energy harvesting architecture that combines energy from multiple energy harvesting sources- photovoltaic, thermoelectric and piezoelectric sources. Digital control circuits that configure the power trains to new efficient system architectures with maximum power point tracking are presented, while using a single inductor to combine energy from the aforementioned energy sources all at the same time. A dual-path architecture for energy harvesting systems is proposed. This provides a peak efficiency improvement of 11-13% over the traditional two stage approach. The system can handle input voltages from 20mV to 5V and is also capable of extracting maximum power from individual harvesters all at the same time utilizing a single inductor. A proposed completely digital timebased power monitor is used for achieving maximum power point tracking for the photovoltaic harvester. This has a peak tracking efficiency of 96%. The peak efficiencies achieved with inductor sharing are 83%, 58% and 79% for photovoltaic boost, thermoelectric boost and piezoelectric buck-boost converters respectively. The switch matrix and the control circuits are implemented on a 0.35pm CMOS process. This part of the thesis highlights how digital control circuits can help reconfigure power converter architectures for improving efficiency and reducing form-factors. The last part of the thesis deals with a power management system for an offline 22W LED driver. In order to reduce the system form factor, Gallium Nitride (GaN) transistors capable of high frequency switching have been utilized with a Quasi-Resonant Inverted Buck architecture. A burst mode digital controller has been used to perform dimming control and power factor correction (PFC) for the LED driver. The custom controller and driver IC was implemented in a 0.35[mu]m CMOS process. The LED driver achieves a peak efficiency of 90.6% and a 0.96 power factor. Due to the high power level of the driver, the digital controller is primarily used for regulation purposes in this system, although the digital nature of the controller helps remove the passives that would be normally present in analog controllers. In this thesis, apart from regulation, control circuit enabled techniques have been used to improve efficiency and reduce system form factor. Low power design and control for reconfigurable power train architectures help improve the overall power converter efficiency. Digital control circuits have been used to reduce the form factor by enabling inductor sharing in a system with multiple power converters or by removing the compensator passives.by Saurav Bandyopadhyay.Ph.D

Architectures and circuits for low-voltage energy conversion and applications in renewable energy and power management

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2012.Cataloged from PDF version of thesis.Includes bibliographical references (p. 337-343).In this thesis we seek to develop smaller, less expensive, and more efficient power electronics. We also investigate emerging applications where the proper implementation of these new types of power converters can have a significant impact on the overall system performance. We have developed a new two-stage dc-dc converter architecture suitable for low-voltage CMOS power delivery. The architecture, which combines the benefits of switched-capacitor and inductor-based converters, achieves both large voltage step-down and high switching frequency, while maintaining good efficiency. We explore the benefits of a new soft-charging technique that drastically reduces the major loss mechanism in switched-capacitor converters, and we show experimental results from a 5-to-1 V, 0.8 W integrated dc-dc converter developed in 180 nm CMOS technology. The use of power electronics to increase system performance in a portable thermophotovoltaic power generator is also investigated in this thesis. We show that mechanical non-idealities in a MEMS fabricated energy conversion device can be mitigated with the help of low-voltage distributed maximum power point tracking (MPPT) dc-dc converters. As part of this work, we explore low power control and sensing architectures, and present experimental results of a 300 mW integrated MPPT developed in 0.35 um CMOS with all power, sensing and control circuitry on chip. The final piece of this thesis investigates the implementation of distributed power electronics in solar photovoltaic applications. We explore the benefits of small, intelligent power converters integrated directly into the solar panel junction box to enhance overall energy capture in real-world scenarios. To this end, we developed a low-cost, high efficiency (>98%) power converter that enables intelligent control and energy conversion at the sub-panel level. Experimental field measurements show that the solution can provide up to a 35% increase in panel output power during partial shading conditions compared to current state-of-the-art solutions.by Robert C. N. Pilawa-Podgurski.Ph.D

Power Management Techniques for Micropower Energy Scavenging

Advances in semi-conductor technology have led to the reduction in size and power consumption of microelectronic circuits. With the miniaturization and increased efficiency of these circuits there are more potential applications for wireless sensor networks and portable electronic equipment. These applications include structural integrity and environment monitoring such as aircraft wing health monitoring and forest fire and natural disaster detection. Biomedical devices have also benefited from the improved size and performance of microelectronics. This thesis studies power management techniques to enable efficient energy scavenging at micropower input power levels from a number of power sources. These sources range from temperature gradients, radio frequency (RF) radiation, solar power, and mechanical vibrations. The scavenged energy is used to improve the performance and distribution of wireless sensors and devices by supplementing or potentially replacing the local power supply of the sensor or device. The major focus of this thesis is to combine source characterization, power management theory, detailed power loss analysis, and ultra-low power circuit design to maximize the extraction of energy from source and deliver it to the wireless sensor or device. The resistor emulation techniques from power factor correction (PFC) are leveraged to load an RF rectifying antenna (rectenna) such that maximum power point tracking (MPPT) of the rectenna is achieved naturally. An application specific integrated circuit (ASIC) is developed to implement this technique after experimental verification with commercially available discrete circuitry. Experimental results show efficient energy scavenging at power levels below 2 microwatts. In addition to resistor emulation, synchronous electric charge extraction (SECE) for energy scavenging from piezoelectric generators is also investigated. The presented techniques allow for the scavenging of usable power for sensors at power levels significantly lower than previous research

Efficient power management circuits for energy harvesting applications

Low power IoT devices are growing in numbers and by 2020 there will be more than 25 Billion of those in areas such as wearables, smart homes, remote surveillance, transportation and industrial systems, including many others. Many IoT electronics either will operate from stand-alone energy supply (e.g., battery) or be self-powered by harvesting from ambient energy sources or have both options. Harvesting sustainable energy from ambient environment plays significant role in extending the operation lifetime of these devices and hence, lower the maintenance cost of the system, which in turn help make them integral to simpler systems. Both for battery-powered and harvesting capable systems, efficient power delivery unit remains an essential component for maximizing energy efficiency. The goal of this research is to investigate the challenges of energy delivery for low power electronics considering both energy harvesting as well as battery-powered conditions and to address those challenges. Different challenges of energy harvesting from low voltage energy sources based on the limitations of the sources, the type of the regulator used and the pattern of the load demands have been investigated. Different aspects of the each challenges are further investigated to seek optimized solutions for both load specific and generalized applications. A voltage boost mechanism is chosen as the primary mechanism to investigate and to addressing those challenges, befitting the need for low power applications which often rely on battery voltage or on low voltage energy harvesting sources. Additionally, a multiple output buck regulator is also discussed. The challenges analyzed include very low voltage start up issues for an inductive boost regulator, cascading of boost regulator stages, and reduction of the number of external component through reusing those. Design techniques for very high conversion ratio, bias current reduction with autonomous bias gating, battery-less cold start, component and power stage multiplexing for reconfigurable and multi-domain regulators are presented. Measurement results from several silicon prototypes are also presented.Ph.D

Power Management Circuits for Energy Harvesting Applications

Energy harvesting is the process of converting ambient available energy into usable electrical energy. Multiple types of sources are can be used to harness environmental energy: solar cells, kinetic transducers, thermal energy, and electromagnetic waves. This dissertation proposal focuses on the design of high efficiency, ultra-low power, power management units for DC energy harvesting sources. New architectures and design techniques are introduced to achieve high efficiency and performance while achieving maximum power extraction from the sources. The first part of the dissertation focuses on the application of inductive switching regulators and their use in energy harvesting applications. The second implements capacitive switching regulators to minimize the use of external components and present a minimal footprint solution for energy harvesting power management. Analysis and theoretical background for all switching regulators and linear regulators are described in detail. Both solutions demonstrate how low power, high efficiency design allows for a self-sustaining, operational device which can tackle the two main concerns for energy harvesting: maximum power extraction and voltage regulation. Furthermore, a practical demonstration with an Internet of Things type node is tested and positive results shown by a fully powered device from harvested energy. All systems were designed, implemented and tested to demonstrate proof-of-concept prototypes

Sub 1V Charge Pump based Micro Scale Energy Harvesting for Low Power Application

Harvesting energy from our environment is a promising solution to provide power to wireless sensor network, wearable devices and biomedical implantation. Now a days, usage of battery power system has disappeared because of replacement issues, installation costs every periodic year and the possibility of health hazard in the case of biomedical implants. Considering these issues, energy harvesting proves to be the most feasible and convenient option in the case of wearable devices and biomedical implantation. Hence, we have focused on indoor single solar cell energy harvesting to power ultra-low power load. The tree topology DC-DC converter is used for power management circuit with optimized efficiency. High efficiency is achieved by using ZVT MOSCAP. The power management circuit includes DC-DC converter and feed forward maximum power point tracking algorithm to transfer maximum power from the single solar cell. The system has ultra-low power battery protection and input condition sensor circuit to extend the life of the battery by protecting from overcharging and over discharging. Also, cold start up circuit is used to run the system when battery voltage drains out to zero. The objective of this system to make complete energy harvester unit is to drive wide range of ultra-low power applications. We have driven the ZigBee receiver to validate our system and the system works effectively

Power management systems based on switched-capacitor DC-DC converter for low-power wearable applications

The highly efficient ultra-low-power management unit is essential in powering low-power wearable electronics. Such devices are powered by a single input source, either by a battery or with the help of a renewable energy source. Thus, there is a demand for an energy conversion unit, in this case, a DC-DC converter, which can perform either step-up or step-down conversions to provide the required voltage at the load. Energy scavenging with a boost converter is an intriguing choice since it removes the necessity of bulky batteries and considerably extends the battery life. Wearable devices are typically powered by a monolithic battery. The commonly available battery such as Alkaline or Lithium-ion, degrade over time due to their life spans as it is limited by the number of charge cycles- which depend highly on the environmental and loading condition. Thus, once it reaches the maximum number of life cycles, the battery needs to be replaced. The operation of the wearable devices is limited by usable duration, which depends on the energy density of the battery. Once the stored energy is depleted, the operation of wearable devices is also affected, and hence it needs to be recharged. The energy harvesters- which gather the available energy from the surroundings, however, have no limitation on operating life. The application can become battery-less given that harvestable energy is sufficiently powering the low-power devices. Although the energy harvester may not completely replace the battery source, it ensures the maximum duration of use and assists to become autonomous and self-sustain devices. The photovoltaic (PV) cell is a promising candidate as a hypothetical input supply source among the energy harvesters due to its smaller area and high power density over other harvesters. Solar energy use PV harvester can convert ambient light energy into electrical energy and keep it in the storage device. The harvested output of PV cannot directly connect to wearable loads for two main reasons. Depending on the incoming light, the harvested current result in varying open-circuit voltage. It requires the power management circuit to deal with unregulated input variation. Second, depending on the PV cell's material type and an effective area, the I-V characteristic's performance varies, resulting in a variation of the output power. There are several works of maximum power point tracking (MPPT) methods that allow the solar energy harvester to achieve optimal harvested power. Therefore, the harvested power depends on the size and usually small area cell is sufficient for micro-watt loads low-powered applications. The available harvested voltage, however, is generally very low-voltage range between 0.4-0.6 V. The voltage ratings of electronics in standard wearable applications operate in 1.8-3 V voltages as described in introduction’s application example section. It is higher than the supply source can offer. The overcome the mismatch voltage between source and supply circuit, a DC-DC boost converter is necessary. The switch-mode converters are favoured over the linear converters due to their highly efficient and small area overhead. The inductive converter in the switch-mode converter is common due to its high-efficiency performance. However, the integration of the inductor in the miniaturised integrated on-chip design tends to be bulky. Therefore, the switched-capacitor approach DC-DC converters will be explored in this research. In the switched-capacitor converter universe, there is plenty of work for single-output designs for various topologies. Most converters are reconfigurable to the different DC voltage levels apart from Dickson and cross-coupled charge pump topologies due to their boosting power stage architecture through a number of stages. However, existing multi-output converters are limited to the fixed gain ratio. This work explores the reconfigurable dual-output converter with adjustable gain to compromise the research gap. The thesis's primary focus is to present the inductor-less, switched-capacitor-based DC-DC converter power management system (PMS) supplied by a varying input of PV energy harvester input source. The PMS should deliver highly efficient regulated voltage conversion ratio (VCR) outputs to low-power wearable electronic devices that constitute multi-function building blocks

Multiple-output DC–DC converters: applications and solutions

Multiple-output DC–DC converters are essential in a multitude of applications where different DC output voltages are required. The interest and importance of this type of multiport configuration is also reflected in that many electronics manufacturers currently develop integrated solutions. Traditionally, the different output voltages required are obtained by means of a transformer with several windings, which are in addition to providing electrical isolation. However, the current trend in the development of multiple-output DC–DC converters follows general aspects, such as low losses, high-power density, and high efficiency, as well as the development of new architectures and control strategies. Certainly, simple structures with a reduced number of components and power switches will be one of the new trends, especially to reduce the size. In this sense, the incorporation of devices with a Wide Band Gap (WBG), particularly Gallium Nitride (GaN) and Silicon Carbide (SiC), will establish future trends, advantages, and disadvantages in the development and applications of multiple-output DC–DC converters. In this paper, we present a review of the most important topics related to multiple-output DC–DC converters based on their main topologies and configurations, applications, solutions, and trends. A wide variety of configurations and topologies of multiple-output DC–DC converters are shown (more than 30), isolated and non-isolated, single and multiple switches, and based on soft and hard switching techniques, which are used in many different applications and solutions.info:eu-repo/semantics/publishedVersio