Massive MIMO transmission techniques

Next generation of mobile communication systems must support astounding data traffic increases, higher data rates and lower latency, among other requirements. These requirements should be met while assuring energy efficiency for mobile devices and base stations. Several technologies are being proposed for 5G, but a consensus begins to emerge. Most likely, the future core 5G technologies will include massive MIMO (Multiple Input Multiple Output) and beamforming schemes operating in the millimeter wave spectrum. As soon as the millimeter wave propagation difficulties are overcome, the full potential of massive MIMO structures can be tapped. The present work proposes a new transmission system with bi-dimensional antenna arrays working at millimeter wave frequencies, where the multiple antenna configurations can be used to obtain very high gain and directive transmission in point to point communications. A combination of beamforming with a constellation shaping scheme is proposed, that enables good user isolation and protection against eavesdropping, while simultaneously assuring power efficient amplification of multi-level constellations

Efficient DSP and Circuit Architectures for Massive MIMO: State-of-the-Art and Future Directions

Massive MIMO is a compelling wireless access concept that relies on the use of an excess number of base-station antennas, relative to the number of active terminals. This technology is a main component of 5G New Radio (NR) and addresses all important requirements of future wireless standards: a great capacity increase, the support of many simultaneous users, and improvement in energy efficiency. Massive MIMO requires the simultaneous processing of signals from many antenna chains, and computational operations on large matrices. The complexity of the digital processing has been viewed as a fundamental obstacle to the feasibility of Massive MIMO in the past. Recent advances on system-algorithm-hardware co-design have led to extremely energy-efficient implementations. These exploit opportunities in deeply-scaled silicon technologies and perform partly distributed processing to cope with the bottlenecks encountered in the interconnection of many signals. For example, prototype ASIC implementations have demonstrated zero-forcing precoding in real time at a 55 mW power consumption (20 MHz bandwidth, 128 antennas, multiplexing of 8 terminals). Coarse and even error-prone digital processing in the antenna paths permits a reduction of consumption with a factor of 2 to 5. This article summarizes the fundamental technical contributions to efficient digital signal processing for Massive MIMO. The opportunities and constraints on operating on low-complexity RF and analog hardware chains are clarified. It illustrates how terminals can benefit from improved energy efficiency. The status of technology and real-life prototypes discussed. Open challenges and directions for future research are suggested.Comment: submitted to IEEE transactions on signal processin

Space-Air-Ground Integrated 6G Wireless Communication Networks: A Review of Antenna Technologies and Application Scenarios

A review of technological solutions and advances in the framework of a Vertical Heterogeneous Network (VHetNet) integrating satellite, airborne and terrestrial networks is presented. The disruptive features and challenges offered by a fruitful cooperation among these segments within a ubiquitous and seamless wireless connectivity are described. The available technologies and the key research directions for achieving global wireless coverage by considering all these layers are thoroughly discussed. Emphasis is placed on the available antenna systems in satellite, airborne and ground layers by highlighting strengths and weakness and by providing some interesting trends in research. A summary of the most suitable applicative scenarios for future 6G wireless communications are finally illustrated

Implementação de códigos LDPC em OFDM e SC-FDE

Os desenvolvimentos dos sistemas de comunicação sem fios apontam para transmissões de alta velocidade e alta qualidade de serviço com um uso eficiente de energia. Eficiência espectral pode ser obtida por modulações multinível, enquanto que melhorias na eficiência de potência podem ser proporcionadas pelo uso de códigos corretores de erros. Os códigos Low-Density Parity-Check (LDPC), devido ao seu desempenho próximo do limite de Shannon e baixa complexidade na implementação e descodificação são apropriados para futuros sistemas de comunicações sem fios. Por outro lado, o uso de modulações multinível acarreta limitações na amplificação. Contudo, uma amplificação eficiente pode ser assegurada por estruturas de transmissão onde as modulações multinível são decompostas em submodulações com envolvente constante que podem ser amplificadas por amplificadores não lineares a operar na zona de saturação. Neste tipo de estruturas surgem desvios de fase e ganho, produzindo distorções na constelação resultante da soma de todos os sinais amplificados. O trabalho foca-se no uso dos códigos LDPC em esquemas multiportadora e monoportadora, com especial ênfase na performance de uma equalização iterativa implementada no domínio da frequência por um Iterative Block-Decision Feedback Equalizer (IB-DFE). São analisados aspectos como o impacto do número de iterações no processo de descodificação dentro das iterações do processo de equalização. Os códigos LDPC também serão utilizados para compensar os desvios de fase em recetores iterativos para sistemas baseados em transmissores com vários ramos de amplificação. É feito um estudo sobre o modo como estes códigos podem aumentar a tolerância a erros de fase que incluí uma análise da complexidade e um algoritmo para estimação dos desequilíbrios de fase

Direct Antenna Modulation using Frequency Selective Surfaces

In the coming years, the number of connected wireless devices will increase dramatically, expanding the Internet of Things (IoT). It is likely that much of this capacity will come from network densification. However, base stations are inefficient and expensive, particularly the downlink transmitters. The main cause of this is the power amplifier (PA), which must amplify complex signals, so are expensive and often only 30% efficient. As such, the cost of densifying cellular networks is high. This thesis aims to overcome this problem through codesign of a low complexity, energy efficient transmitter through electromagnetic design; and a waveform which leverages the advantages and mitigates the disadvantages of the new technology, while being suitable for supporting IoT devices. Direct Antenna Modulation (DAM) is a low complexity transmitter architecture, where modulation occurs at the antenna at transmit power. This means a non-linear PA can efficiently amplify the carrier wave without added distortion. Frequency Selective Surfaces (FSS) are presented here as potential phase modulators for DAM transmitters. The theory of operation is discussed, and a prototype DAM for QPSK modulation is simulated, designed and tested. Next, the design process for a continuous phase modulating antenna is explored. Simulations and measurement are used to fully characterise a prototype, and it is implemented in a line-of-sight end-to-end communications system, demonstrating BPSK, QPSK and 8-PSK. Due to the favourable effects of spread spectrum signalling on FSS DAM performance, Cyclic Prefix Direct Sequence Spread Spectrum (CPDSSS) is developed. Conventional spreading techniques are extended using a cyclic prefix, making multipath interference entirely defined by the periodic autocorrelation of the sequence used. This is demonstrated analytically, through simulation and with experiments. Finally, CPDSSS is implemented using FSS DAM, demonstrating the potential of this new low cost, low complexity transmitter with CPDSSS as a scalable solution to IoT connectivity