Multi-band OFDM UWB receiver with narrowband interference suppression

A multi band orthogonal frequency division multiplexing (MB-OFDM) compatible ultra wideband (UWB) receiver with narrowband interference (NBI) suppression capability is presented. The average transmit power of UWB system is limited to -41.3 dBm/MHz in order to not interfere existing narrowband systems. Moreover, it must operate even in the presence of unintentional radiation of FCC Class-B compatible devices. If this unintentional radiation resides in the UWB band, it can jam the communication. Since removing the interference in digital domain requires higher dynamic range of analog front-end than removing it in analog domain, a programmable analog notch filter is used to relax the receiver requirements in the presence of NBI. The baseband filter is placed before the variable gain amplifier (VGA) in order to reduce the signal swing at the VGA input. The frequency hopping period of MB-OFDM puts a lower limit on the settling time of the filter, which is inverse proportional to notch bandwidth. However, notch bandwidth should be low enough not to attenuate the adjacent OFDM tones. Since these requirements are contradictory, optimization is needed to maximize overall performance. Two different NBI suppression schemes are tested. In the first scheme, the notch filter is operating for all sub-bands. In the second scheme, the notch filter is turned on during the sub-band affected by NBI. Simulation results indicate that the UWB system with the first and the second suppression schemes can handle up to 6 dB and 14 dB more NBI power, respectively. The results of this work are not limited to MB-OFDM UWB system, and can be applied to other frequency hopping systems

Design of a Cost-Efficient Reconfigurable Pipeline ADC

Power budget is very critical in the design of battery-powered implantable biomedical instruments. High speed, high resolution and low power usually cannot be achieved at the same time. Therefore, a tradeoff must be made to compromise every aspect of those features. As the main component of the bioinstrument, high conversion rate, high resolution ADC consumes most of the power. Fortunately, based on the operation modes of the bioinstrument, a reconfigurable ADC can be used to solve this problem. The reconfigurable ADC will operate at 10-bit 40 MSPS for the diagnosis mode and at 8-bit 2.5 MSPS for the monitor mode. The ADC will be completely turned off if no active signal comes from sensors or if an off command is received from the antenna. By turning off the sample hold stage and the first two stages of the pipeline ADC, a significant power saving is achieved. However, the reconfigurable ADC suffers from two drawbacks. First, the leakage signals through the extra off-state switches in the third stage degrade the performance of the data converter. This situation tends to be even worse for high speed and high-resolution applications. An interference elimination technique has been proposed in this work to solve this problem. Simulation results show a significant attenuation of the spurious tones. Moreover, the transistors in the OTA tend to operate in weak inversion region due to the scaling of the bias current. The transistor in subthreshold is very slow due to the small transit frequency. In order to get a better tradeoff between the transconductance efficiency and the transit frequency, reconfigurable OTAs and scalable bias technique are devised to adjust the operating point from weak inversion to moderate inversion. The figure of merit of the reconfigurable ADC is comparable to the previously published conventional pipeline ADCs. For the 10-bit, 40 MSPS mode, the ADC attains a 56.9 dB SNDR for 35.4 mW power consumption. For the 8-bit 2.5 MSPS mode, the ADC attains a 49.2 dB SNDR for 7.9 mW power consumption. The area for the core layout is 1.9 mm2 for a 0.35 micrometer process

Accurate and robust spectral testing with relaxed instrumentation requirements

Spectral testing has been widely used to characterize the dynamic performances of the electrical signals and devices, such as Analog-to-Digital Converters (ADCs) for many decades. One of the difficulties faced is to accurately and cost-effectively test the continually higher performance devices. Standard test methods can be difficult to implement accurately and cost effectively, due to stringent requirements. To relax these necessary conditions and to reduce test costs, while achieving accurate spectral test results, several new algorithms are developed to perform accurate spectral and linearity test without requiring precise, expensive instruments. In this dissertation, three classes of methods for overcoming the above difficulties are presented. The first class of methods targeted the accurate, single-tone spectral testing. The first method targets the non-coherent sampling issue on spectral testing, especially when the non-coherently sampled signal has large distortions. The second method resolves simultaneous amplitude and frequency drift with non-coherent sampling. The third method achieves accurate linearity results for DAC-ADC co-testing, and generates high-purity sine wave using the nonlinear DAC in the system via pre-distortion. The fourth method targets ultra-pure sine wave generation with two nonlinear DACs, two simple filters, and a nonlinear ADC. These proposed methods are validated by both simulation and measurement results, and have demonstrated their high accuracy and robustness against various test conditions. The second class of methods deals with the accurate multi-tone spectral testing. The first method in this class resolves the non-coherent sampling issue in multi-tone spectral testing. The second method in this class introduces another proposed method to deal with multi-tone impure sources in spectral testing. The third method generates the multi-tone sine wave with minimum peak-to-average power ratio, which can be implemented in many applications, such as spectral testing and signal analysis. Similarly, simulation and measurement results validate the functionality and robustness of these proposed methods. Finally, the third class introduces two proposed methods to accurately test linearity characteristics of high-performance ADCs using low purity sinusoidal or ramp stimulus in the presence of flicker noise. Extensive simulation results have verified their effectiveness to reduce flicker noise influence and achieve accurate linearity results

Time-based circuits for communication systems in advanced CMOS technology

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2009.This electronic version was submitted by the student author. The certified thesis is available in the Institute Archives and Special Collections.Cataloged from student submitted PDF version of thesis.Includes bibliographical references (p. 145-151).As device size scales down, there have been challenges to design conventional analog circuits, such as low voltage headroom and the low intrinsic gain of a device. Although ever-decreasing device channel length in CMOS technology has mainly negative effects on analog circuits, it increases device speed and reduces the power consumption of digital circuits. As a result, time-based signal processing has been attracting attention because time-based circuits take advantage of high speed and low power devices to deal with analog information in the time domain. In this thesis, we focus on a ring oscillator as a core time-based circuit for communication systems. Ring oscillators are employed in analog-to-time conversion or time-to-digital conversion. In this work, we present A/D converters and an RF modulator based on ring oscillators in deep sub-micron CMOS processes. We introduce a VCO-based [sigma][delta] A/D converter utilizing a voltage-controlled ring oscillator (ring VCO) as a continuous-time integrator. We propose to replace conventional integrators designed with analog circuits in a [sigma][delta] modulator with a ring VCO and a phase detector, thereby implementing an A/D converter without traditional analog circuits. We also propose a single-slope A/D converter using time-to-digital conversion. By combining a few analog circuits and a ring oscillator based Time-to-Digital Converter (TDC), we achieve highly digital A/D conversion. Finally, we demonstrate a VCO-based RF modulator. The proposed RF modulator generates an RF signal by simply switching transistors. As opposed to an RFDAC approach, the proposed RF modulator is not limited by quantization noise because it employs multiphase PWM signals. A VCO-based OP amp is also introduced as an alternative method of designing an OP amp in deep sub-micron CMOS. The proposed VCO-based OP amp is utilized to generate the multiphase PWM signals in the RF modulator. This thesis also presents the fundamental limitations of a ring oscillator as a timebased circuit. Although the idea of time-based signal processing employing a ring oscillator has its own limitations such as non-linear tuning characteristics and phase noise, the basic idea is worth investigating to solve the serious problems of analog circuits for future CMOS technology.by Min Park.Ph.D

Multi-band OFDM UWB receiver with narrowband interference suppression

A multi band orthogonal frequency division multiplexing (MB-OFDM) compatible ultra wideband (UWB) receiver with narrowband interference (NBI) suppression capability is presented. The average transmit power of UWB system is limited to -41.3 dBm/MHz in order to not interfere existing narrowband systems. Moreover, it must operate even in the presence of unintentional radiation of FCC Class-B compatible devices. If this unintentional radiation resides in the UWB band, it can jam the communication. Since removing the interference in digital domain requires higher dynamic range of analog front-end than removing it in analog domain, a programmable analog notch filter is used to relax the receiver requirements in the presence of NBI. The baseband filter is placed before the variable gain amplifier (VGA) in order to reduce the signal swing at the VGA input. The frequency hopping period of MB-OFDM puts a lower limit on the settling time of the filter, which is inverse proportional to notch bandwidth. However, notch bandwidth should be low enough not to attenuate the adjacent OFDM tones. Since these requirements are contradictory, optimization is needed to maximize overall performance. Two different NBI suppression schemes are tested. In the first scheme, the notch filter is operating for all sub-bands. In the second scheme, the notch filter is turned on during the sub-band affected by NBI. Simulation results indicate that the UWB system with the first and the second suppression schemes can handle up to 6 dB and 14 dB more NBI power, respectively. The results of this work are not limited to MB-OFDM UWB system, and can be applied to other frequency hopping systems

A Low-Power, Reconfigurable, Pipelined ADC with Automatic Adaptation for Implantable Bioimpedance Applications

Biomedical monitoring systems that observe various physiological parameters or electrochemical reactions typically cannot expect signals with fixed amplitude or frequency as signal properties can vary greatly even among similar biosignals. Furthermore, advancements in biomedical research have resulted in more elaborate biosignal monitoring schemes which allow the continuous acquisition of important patient information. Conventional ADCs with a fixed resolution and sampling rate are not able to adapt to signals with a wide range of variation. As a result, reconfigurable analog-to-digital converters (ADC) have become increasingly more attractive for implantable biosensor systems. These converters are able to change their operable resolution, sampling rate, or both in order convert changing signals with increased power efficiency. Traditionally, biomedical sensing applications were limited to low frequencies. Therefore, much of the research on ADCs for biomedical applications focused on minimizing power consumption with smaller bias currents resulting in low sampling rates. However, recently bioimpedance monitoring has become more popular because of its healthcare possibilities. Bioimpedance monitoring involves injecting an AC current into a biosample and measuring the corresponding voltage drop. The frequency of the injected current greatly affects the amplitude and phase of the voltage drop as biological tissue is comprised of resistive and capacitive elements. For this reason, a full spectrum of measurements from 100 Hz to 10-100 MHz is required to gain a full understanding of the impedance. For this type of implantable biomedical application, the typical low power, low sampling rate analog-to-digital converter is insufficient. A different optimization of power and performance must be achieved. Since SAR ADC power consumption scales heavily with sampling rate, the converters that sample fast enough to be attractive for bioimpedance monitoring do not have a figure-of-merit that is comparable to the slower converters. Therefore, an auto-adapting, reconfigurable pipelined analog-to-digital converter is proposed. The converter can operate with either 8 or 10 bits of resolution and with a sampling rate of 0.1 or 20 MS/s. Additionally, the resolution and sampling rate are automatically determined by the converter itself based on the input signal. This way, power efficiency is increased for input signals of varying frequency and amplitude

An improved sigma-delta modulator for digitizing carrier band measurements

Thesis (M. Eng.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2005.Includes bibliographical references (p. 97-99).Draper Laboratory currently employs a third-order Sigma-Delta modulator to digitize the outputs from microelectromechanical sensors at the intermediate frequency prior to demodulation inside a field programmable gate array. This modulator, which is built on a .5[mu]m CMOS process, is to be used as a standalone chip or as a core for use in larger microelectromechanical sensor integrated circuits. In this document, I submit the design of an improved Sigma-Delta modulator, which has a noise floor of 40nV/ [square root of] Hz and a 5Vpp input range.by John Gerard Puskarich.M.Eng

High-Bandwidth Voltage-Controlled Oscillator based architectures for Analog-to-Digital Conversion

The purpose of this thesis is the proposal and implementation of data conversion open-loop architectures based on voltage-controlled oscillators (VCOs) built with ring oscillators (RO-based ADCs), suitable for highly digital designs, scalable to the newest complementary metal-oxide-semiconductor (CMOS) nodes. The scaling of the design technologies into the nanometer range imposes the reduction of the supply voltage towards small and power-efficient architectures, leading to lower voltage overhead of the transistors. Additionally, phenomena like a lower intrinsic gain, inherent noise, and parasitic effects (mismatch between devices and PVT variations) make the design of classic structures for ADCs more challenging. In recent years, time-encoded A/D conversion has gained relevant popularity due to the possibility of being implemented with mostly digital structures. Within this trend, VCOs designed with ring oscillator based topologies have emerged as promising candidates for the conception of new digitization techniques. RO-based data converters show excellent scalability and sensitivity, apart from some other desirable properties, such as inherent quantization noise shaping and implicit anti-aliasing filtering. However, their nonlinearity and the limited time delay achievable in a simple NOT gate drastically limits the resolution of the converter, especially if we focus on wide-band A/D conversion. This thesis proposes new ways to alleviate these issues. Firstly, circuit-based techniques to compensate for the nonlinearity of the ring oscillator are proposed and compared to equivalent state-of-the-art solutions. The proposals are designed and simulated in a 65-nm CMOS node for open-loop RO-based ADC architectures. One of the techniques is also validated experimentally through a prototype. Secondly, new ways to artificially increase the effective oscillation frequency are introduced and validated by simulations. Finally, new approaches to shape the quantization noise and filter the output spectrum of a RO-based ADC are proposed theoretically. In particular, a quadrature RO-based band-pass ADC and a power-efficient Nyquist A/D converter are proposed and validated by simulations. All the techniques proposed in this work are especially devoted for highbandwidth applications, such as Internet-of-Things (IoT) nodes or maximally digital radio receivers. Nevertheless, their field of application is not restricted to them, and could be extended to others like biomedical instrumentation or sensing.El propósito de esta tesis doctoral es la propuesta y la implementación de arquitecturas de conversión de datos basadas en osciladores en anillos, compatibles con diseños mayoritariamente digitales, escalables en los procesos CMOS de fabricación más modernos donde las estructuras digitales se ven favorecidas. La miniaturización de las tecnologías CMOS de diseño lleva consigo la reducción de la tensión de alimentación para el desarrollo de arquitecturas pequeñas y eficientes en potencia. Esto reduce significativamente la disponibilidad de tensión para saturar transistores, lo que añadido a una ganancia cada vez menor de los mismos, ruido y efectos parásitos como el “mismatch” y las variaciones de proceso, tensión y temperatura han llevado a que sea cada vez más complejo el diseño de estructuras analógicas eficientes. Durante los últimos años la conversión A/D basada en codificación temporal ha ganado gran popularidad dado que permite la implementación de estructuras mayoritariamente digitales. Como parte de esta evolución, los osciladores controlados por tensión diseñados con topologías de oscilador en anillo han surgido como un candidato prometedor para la concepción de nuevas técnicas de digitalización. Los convertidores de datos basados en osciladores en anillo son extremadamente sensibles (variación de frecuencia con respecto a la señal de entrada) así como escalables, además de otras propiedades muy atractivas, como el conformado espectral de ruido de cuantificación y el filtrado “anti-aliasing”. Sin embargo, su respuesta no lineal y el limitado tiempo de retraso alcanzable por una compuerta NOT restringen la resolución del conversor, especialmente para conversión A/D en aplicaciones de elevado ancho de banda. Esta tesis doctoral propone nuevas técnicas para aliviar este tipo de problemas. En primer lugar, se proponen técnicas basadas en circuito para compensar el efecto de la no linealidad en los osciladores en anillo, y se comparan con soluciones equivalentes ya publicadas. Las propuestas se diseñan y simulan en tecnología CMOS de 65 nm para arquitecturas en lazo abierto. Una de estas técnicas presentadas es también validada experimentalmente a través de un prototipo. En segundo lugar, se introducen y validan por simulación varias formas de incrementar artificialmente la frecuencia de oscilación efectiva. Para finalizar, se proponen teóricamente dos enfoques para configurar nuevas formas de conformación del ruido de cuantificación y filtrado del espectro de salida de los datos digitales. En particular, son propuestos y validados por simulación un ADC pasobanda en cuadratura de fase y un ADC de Nyquist de gran eficiencia en potencia. Todas las técnicas propuestas en este trabajo están destinadas especialmente para aplicaciones de alto ancho de banda, tales como módulos para el Internet de las cosas o receptores de radiofrecuencia mayoritariamente digitales. A pesar de ello, son extrapolables también a otros campos como el de la instrumentación biomédica o el de la medición de señales mediante sensores.Programa de Doctorado en Ingeniería Eléctrica, Electrónica y Automática por la Universidad Carlos III de MadridPresidente: Juan Pablo Alegre Pérez.- Secretario: Celia López Ongil.- Vocal: Fernando Cardes Garcí

CMOS RF front-end design for terrestrial and mobile digital television systems

With the increasing demand for high quality TV service, digital television (DTV) is replacing the conventional analog television. DTV tuner is one of the most critical blocks of the DTV receiver system; it down-converts the desired DTV RF channel to baseband or a low intermediate frequency with enough quality. This research is mainly focused on the analysis and realization of low-cost low-power front-ends for ATSC terrestrial DTV and DVB-H mobile DTV tuner systems. For the design of the ATSC terrestrial tuner, a novel double quadrature tuner architecture, which can not only minimize the tuner power consumption but also achieve the fully integration, has been proposed. A double quadrature down-converter has been designed and fabricated with TSMC 0.35õm CMOS technology; the measurement results verified the proposed concepts. For the mobile DTV tuner, a zero-IF architecture is used and it can achieve the DVB-H specifications with less than 200mW power consumption. In the implementation of the mobile DVB-H tuner, a novel RF variable gain amplifier (RFVGA) and a low flicker noise current-mode passive mixer have been proposed. The proposed RFVGA achieves high dynamic range and robust input impedance matching performance, which is the main design challenge for the traditional implementations. The current-mode passive mixer achieves high-gain, low noise (especially low flicker noise) and high-linearity (over 10dBm IIP3) with low power supplies; it is believed that this is a promising topology for low voltage high dynamic range mixer applications. The RFVGA has been fabricated in TSMC 0.18õm CMOS technology and the measurement results agree well with the theoretical ones