Two–Way Relaying Communications with OFDM and BICM/BICM-ID

Relay-aided communication methods have gained strong interests in academic community and been applied in various wireless communication scenarios. Among different techniques in relay-aided communication system, two-way relaying communication (TWRC) achieves the highest spectral efficiency due to its bi-directional transmission capability. Nevertheless, different from the conventional point-to-point communication system, TWRC suffers from detection quality degradation caused by the multiple-access interference (MAI). In addition, because of the propagation characteristics of wireless channels, fading and multipath dispersion also contribute strongly to detection errors. Therefore, this thesis is mainly concerned with designing transmission and detection schemes to provide good detection quality of TWRC while taking into account the negative impacts of fading, multipath dispersion and multiple-access interference. First, a TWRC system operating over multipath fading channels is considered and orthogonal frequency-division multiplexing (OFDM) is adopted to handle the inter-symbol interference (ISI) caused by the multipath dispersion. In particular, adaptive physical-layer network coding (PNC) is employed to address the MAI issue. By analyzing the detection error probability, various adaptive PNC schemes are discussed for using with OFDM and the scheme achieving the best trade-off among performance, overhead and complexity is suggested. In the second part of the thesis, the design of distributed precoding in TWRC using OFDM under multipath fading channels is studied. The objective is to design a distributed precoding scheme which can alleviate MAI and achieve multipath diversity to combat fading. Specifically, three types of errors are introduced when analyzing the error probability in the multiple access (MA) phase. Through analysis and simulation, the scheme that performs precoding in both time and frequency domains is demonstrated to achieve the maximum diversity gains under all types of errors. Finally, the last part of the thesis examines a communication system incorporating forward error correction (FEC) codes. Specifically, bit-interleaved code modulation (BICM) without and with iterative decoding (BICM-ID) are investigated in a TWRC system. Distributed linear constellation precoding (DLCP) is applied to handle MAI and the design of DLCP in a TWRC system using BICM/BICM-ID is discussed. Taking into account the multiple access channel from the terminal nodes to the relay node, decoding based on the quaternary code representation is introduced. Several error probability bounds are derived to aid in the design of DLCP. Based on these bounds, optimal parameters of DLCP are obtained through analysis and computer search. It is also found that, by combining XORbased network coding with successful iterative decoding, the MAI is eliminated and thus DLCP is not required in a BICM-ID system

Parallel packet transmission based on OFDM

This paper proposes a parallel packet transmission (PPT) scheme based on orthogonal frequency division multiplexing (OFDM). The principle of the PPT scheme is to divide a packet into a number of smaller parallel packets, and transmit each smaller packet over an individual subcarrier of the OFDM symbols instead of spreading the data bits in a packet across a number of different subcarriers. It is proved theoretically that the proposed PPT scheme has higher average throughput than the conventional serial packet transmission without precoding. Furthermore, simulation results show that the OFDM system with PPT outperforms the precoded OFDM system with minimum mean squared error equalization in both uncoded and coded cases in terms of average throughput. The PPT scheme provides an alternative and simpler means to combat frequency-selective fading. © 2009 IEEE

Improved Spatial Modulation Techniques for Wireless Communications

Transmission and reception methods with multiple antennas have been demonstrated to be very useful in providing high data rates and improving reliability in wireless communications. In particular, spatial modulation (SM) has recently emerged as an attractive transmission method for multiple-antennas systems due to its better energy efficiency and lower system complexity. This thesis is concerned with developing transmission techniques to improve the spectral efficiency of SM where antenna/subcarrier index involves in conveying information bits. In the first part of the thesis, new transmission techniques are developed for SM over frequency-flat fading channels. The first proposed scheme is based on a high-rate space-time block code instead of using the classical Alamouti STBC, which helps to increase the spectral efficiency and achieve a transmit diversity order of two. A simplified maximum likelihood detection is also developed for this proposed scheme. Analysis of coding gains and simulation results demonstrate that the proposed scheme outperforms previously-proposed SM schemes at high data transmission rates. Then, a new space-shift keying (SSK) modulation scheme is proposed which requires a smaller number of transmit antennas than that required in the bi-space shift keying (BiSSK). Such a proposed SSK-based scheme is obtained by multiplexing two in-phase and quadrature generalized SSK streams and optimizing the carrier signals transmitted by the activated antennas. Performance of the proposed scheme is compared with other SSK-based schemes via minimum Euclidean distance analysis and computer simulation. The third scheme proposed in this part is an improved version of quadrature SM (QSM). The main feature of this proposed scheme is to send a second constellation symbol over the in-phase and quadrature antenna dimensions. A significant performance advantage of the proposed scheme is realized at the cost of a slight increase in the number of radio-frequency (RF) chains. Performance comparisons with the most recent SM schemes confirm the advantage of the proposed scheme. The last contribution of the first part is an optimal constellation design for QSM to minimize the average probability of error. It is shown that, the error performance of QSM not only depends on the Euclidean distances between the amplitude phase modulation (APM) symbols and the energies of APM symbols, but also on the in-phase and quadrature components of the QSM symbols. The analysis of the union bound of the average error probability reveals that at a very large number of transmit antennas, the optimal constellations for QSM converge to a quadrature phase shift keying (QPSK) constellation. Simulation results demonstrate the performance superiority of the obtained constellations over other modulation schemes. In the second part of the thesis, the applications of SM in frequency-selective fading channels are studied. First, a new transmission scheme that employs SM for each group of subcarriers in orthogonal frequency-division multiplexing (OFDM) transmission is investigated. Specifically, OFDM symbols in each group are passed through a precoder to maximize the diversity and coding gains, while SM is applied in each group to convey more information bits by antenna indices. Performance analysis and simulation results are carried out to demonstrate the superiority of the proposed scheme over a previously-proposed combination of SM and OFDM. Next, the performance of OFDM based on index modulation and a flexible version of OFDM, knows as OFDM with multiple constellations, is compared for both case of "no precoding'' and "with precoding'' of data symbols. It is shown that the precoded OFDM with multiple constellations outperforms precoded-IM based OFDM systems over frequency-selective fading channels. The last part of the thesis investigates a multiuser downlink transmission system based on in-phase and quadrature space-shift keying modulation and precoding to reduce the minimum number of transmit antennas while keeping the complexity of the receiver low. In addition to the maximum likelihood (ML) detection, the low complexity zero forcing (ZF) receiver is also studied. Theoretical upper bounds for the error probabilities of both ML and ZF receivers are obtained and corroborated with simulation results

Space-time-frequency block codes for MIMO-OFDM in next generation wireless systems

In this thesis the use of space-frequency block codes (SFBC) and space-time-frequency block codes (STFBC) in wireless systems are investigated. A variety of SFBC and STFBC schemes are proposed for particular propagation scenarios and system settings where each has its own advantages and disadvantages. The objective is to pro-pose coding strategies with improved flexibility, feasibility and spectral efficiency,and reduce the decoding complexity in an MIMO-OFDM system. Firstly an efficient SFBC with improved system performance is proposed for MIMO-OFDM systems. The proposed SFBC incorporates the concept of matched rotation precoding (MRP) to achieve full transmit diversity and optimal system performance foran arbitrary numberoftransmitantennas,subcarrierinterval andsubcarriergrouping. The MRP is proposed to exploit the inherent rotation and repetition properties of SFBC, arising from the channel power delay profile, in order to fully capture both space and frequency diversity of SFBC in a MIMO-OFDM system. It is able to relax restrictions on subcarrier interval and subcarrier grouping, making it ideal for adaptive/time-varying systems or multiuser systems. The SFBC without an optimization process is unstable in terms of achievable system performance and diversity order, and also risks diversity loss within a specific propagation scenario. Such loss or risk is prominent while wireless propagation channel has a limited number of dominant paths, e.g. relatively close to transmitters or relatively flat topography. Hence in orderto improve the feasibility of SFBC in dynamic scenarios, the lower bound of the coding gain for MRP is derived. The SFBC with MRP is proposed for more practical scenarios when only partial channel power delay profile information is known at the transmit end, for example the wireless channel has dominant propagation paths. The proposed rate one MRP has a relatively simple optimization process that can be transformed into an explicit diagram and hence an optimal result can be derived intuitively without calculations. Next, a multi-rate transmission strategy is proposed for both SFBCand STFBC to balance the system performance and transmission rate. A variety of rate adaptive coding matrices are obtained by a simple truncation of the coding matrix, or by parameter optimization for coding matrices for a given transmission rate and constellation. Pro-posed strategy can easily and gradually adjust the achievable diversity order. As a result it is capable of achieving a relatively smooth balance between system performance and transmission rate in both SFBC and STFBC, without a significant change of coding structure or constellation size. Such tradeoff would be useful to maintain stable Quality of Service (QoS) for users by providing more scalability of achievable performance in a time-varying channel. Finally the decoding procedure of space-time block code (STBC), SFBCand STFBC is discussed. The decoding of all existing STBC/SFBC/STFBC is unified at first, in order to show a concise procedure and make fair comparisons. Then maximum likelihood decoding (MLD) and arbitrary sphere decoding (SD) can be adopted. To reduce the complexity of decoding further, a novel decoding method called compensation de-coding (CD) is presented for a given space-time-frequency coding scheme. By taking advantage of the simplicity of zero-forcing decoding (ZFD) we are able to calculate a compensation vector for the output of ZFD. After modification by utilizing the com-pensation vector, the BER performance can be improved significantly. The decoding procedure is relatively simple and is independent of the constellation size. The per-formance of the proposed decoding method is close to maximum-likelihood decoding for low to medium SNR. A low complexity detection scheme, classifier based decoding (CBD), is further proposed for MIMO systems incorporating spatial multiplexing. The CBD is a hybrid of an equalizer-based technique and an algorithmic search stage. Based on an error matrix and its probability density functions for different classes of error, a particular search region is selected for the algorithmic stage. As the probability of occurrence of error classes with larger search regions is small, overall complexity of the proposed technique remains low, whilst providing a significant improvement in the bit error rate performance

Design a New Tomlinson-Harashima Non-Linear Pre-Coding Technique for MIMO WiMAX-OFDM Based on Wavelet Signals in Transmit-Antenna

This paper investigates a new technique to the adaptation  the Tomlinson-Harashima non-linear  Pre-coding (THP)  in  the WiMAX baseband, in the physical layer performance of multi-antenna techniques, All cases are based on the IEEE 802.16d standard using OFDM based Wavelet and QPSK (¾) of coding rates. The proposed pre-coding only requires the statistical knowledge of the channel at the transmitter, which significantly reduces the feedback requirements. Both linear and non-linear pre-coders amend the system bit error rate for WiMAX OSTBC DWT OFDM in transmit-antenna and path-correlated channels. The proposed non-linear pre-coder in closed loop design achieved much lower bit error rates, increased signal-to-noise power ratio (SNR) than linear pre-coder. Keywords: WiMAX, THP, OFDM, DWT, MIMO, OSTBC

I/Q imbalance mitigation for space-time block coded communication systems

Multiple-input multiple-output (MIMO) space-time block coded (STBC) wireless communication systems provide reliable data transmissions by exploiting the spatial diversity in fading channels. However, due to component imperfections, the in-phase/quadrature (I/Q) imbalance caused by the non-ideal matching between the relative amplitudes and phases of the I and Q branches always exists in the practical implementation of MIMO STBC communication systems. Such distortion results in a complex conjugate term of the intended signal in the time domain, hence a mirror-image term in the frequency domain, in the data structure. Consequently, I/Q imbalance increases the symbol error rate (SER) drastically in MIMO STBC or STBC MIMO orthogonal frequency division multiplexing (OFDM) communication systems, where both the signal and its complex conjugate are utilized for the information transmission, hence should be mitigated effectively. In this dissertation, the impact of I/Q imbalance in MIMO STBC systems over flat fading channels, the impact of I/Q imbalance in STBC MIMO-OFDM systems and in time- reversal STBC (TR-STBC) systems over frequency-selective fading channels are studied systematically. With regard to the MIMO STBC and the STBC MIMO-OFDM systems with I/Q imbalance, orthogonal space-time block codes (OSTBCs), quasi-orthogonal STBCs (QOSTBCs) and rotated QOSTBCs (RQOSTBCs) are studied, respectively. By exploiting the special structure of the received signal, low-complexity solutions are provided to mitigate the distortion induced by I/Q imbalance successfully. In addition, to mitigate I/Q imbalance while at the same time to exploit the multipath diversity for STBC OFDM systems over frequency-selective fading channels, a new encoding/decoing scheme for the grouped linear constellation precoded (GLCP) OFDM systems with I/Q imbalance is studied. In Chapter 1, the objectives of the research are elaborated. In Chapter 2, the various I/Q imbalance models are introduced, and the model used in this dissertation is established. In Chapter 3, the performance degradation caused by I/Q imbalance of the transceivers in MIMO STBC wireless communication systems over flat fading channels and the solutions are studied. A 2 Tx Alamouti system, a 4 Tx quasi-orthogonal STBC (QOSTBC) system, and a 4 Tx rotated QOSTBC (RQOSTBC) system with I/Q imbalance are studied in detail. By exploiting the special structure of the received signal, low-complexity solutions are proposed to mitigate I/Q imbalance successfully. Since STBCs are developed for frequency-flat fading channels, to achieve the spatial diversity in frequency-selective fading channels, MIMO-OFDM arrangements have been suggested, where STBCs are used across different antennas in conjunction with OFDM. In Chapter 4, the performance degradation caused by I/Q imbalance in STBC MIMO-OFDM wireless systems over frequency-selective fading channels and the solutions are studied. Similarly, a 2 Tx Alamouti system, a 4 Tx quasi-orthogonal STBC (QOSTBC) system, and a 4 Tx rotated QOSTBC (RQOSTBC) system with I/Q imbalance are studied in detail, and low-complexity solutions are proposed to mitigate the distortion effectively. However, OFDM systems suffer from the loss of the multipath diversity by converting frequency-selective fading channels into parallel frequency-flat fading subchannels. To exploit the multipath diversity and reduce the decoding complexity, GLCP OFDM systems with I/Q imbalance are studied. By judiciously assigning the mirror-subcarrier pair into one group, a new encoding/decoding scheme with a low-complexity is proposed to mitigate I/Q imbalance for GLCP OFDM systems in Chapter 5. Since OFDM communication systems have high peak-to-average power ratio (PAPR) problem and are sensitive to carrier frequency offset (CFO), to achieve both the spatial and multipath diversity, time-reversal STBC (TR-STBC) communication systems are introduced. In Chapter 6, the I/Q imbalance mitigating solutions in TR-STBC systems, both in the time domain and in the frequency domain, are studied

Design of encrypted transceiver Non-coherent OFDM with ability to correct coding bits of information

A differential encrypted transceiver was designed in the signal-to-noise ratio systems. A time"-"spread" frequency-"encoded (TSFE) algorithm was proposed using the orthogonal frequency multiplexing multiplier OFDM. The proposed design was verified under the Doppler frequency effect and there was an improvement in the performance of the signal-to-noise ratio system. As a result, the reliability of decoded data was increased and achieves the ability to correct coding bits of information

Index Modulation Techniques for Energy-efficient Transmission in Large-scale MIMO Systems

This thesis exploits index modulation techniques to design energy- and spectrum-efficient system models to operate in future wireless networks. In this respect, index modulation techniques are studied considering two different media: mapping the information onto the frequency indices of multicarrier systems, and onto the antenna array indices of a platform that comprises multiple antennas. The index modulation techniques in wideband communication scenarios considering orthogonal and generalized frequency division multiplexing systems are studied first. Single cell multiuser networks are considered while developing the system models that exploit the index modulation on the subcarriers of the multicarrier systems. Instead of actively modulating all the subcarriers, a subset is selected according to the index modulation bits. As a result, there are subcarriers that remain idle during the data transmission phase and the activation pattern of the subcarriers convey additional information. The transceivers for the orthogonal and generalized frequency division multiplexing systems with index modulation are both designed considering the uplink and downlink transmission phases with a linear combiner and precoder in order to reduce the system complexity. In the developed system models, channel state information is required only at the base station. The linear combiner is designed adopting minimum mean square error method to mitigate the inter-user-interference. The proposed system models offer a flexible design as the parameters are independent of each other. The parameters can be adjusted to design the system in favor of the energy efficiency, spectrum efficiency, peak-to-average power ratio, or error performance. Then, the index modulation techniques are studied for large-scale multiple-input multiple-output systems that operate in millimeter wave bands. In order to overcome the drawbacks of transmission in millimeter wave frequencies, channel properties should be taken in to account while envisaging the wireless communication network. The large-scale multiple-input multiple-output systems increase the degrees of freedom in the spatial domain. This feature can be exploited to focus the transmit power directly onto the intended receiver terminal to cope with the severe path-loss. However, scaling up the number of hardware elements results in excessive power consumption. Hybrid architectures provide a remedy by shifting a part of the signal processing to the analog domain. In this way, the number of bulky and high power consuming hardware elements can be reduced. However, there will be a performance degradation as a consequence of renouncing the fully digital signal processing. Index modulation techniques can be combined with the hybrid system architecture to compensate the loss in spectrum efficiency to further increase the data rates. A user terminal architecture is designed that employs analog beamforming together with spatial modulation where a part of the information bits is mapped onto the indices of the antenna arrays. The system is comprised a switching stage that allocates the user terminal antennas on the phase shifter groups to minimize the spatial correlation, and a phase shifting stage that maximizes the beamforming gain to combat the path-loss. A computationally efficient optimization algorithm is developed to configure the system. The flexibility of the architecture enables optimization of the hybrid transceiver at any signal-to-noise ratio values. A base station is designed in which hybrid beamforming together with spatial modulation is employed. The analog beamformer is designed to point the transmit beam only in the direction of the intended user terminal to mitigate leakage of the transmit power to other directions. The analog beamformer to transmit the signal is chosen based on the spatial modulation bits. The digital precoder is designed to eliminate the inter-user-interference by exploiting the zero-forcing method. The base station computes the hybrid beamformers and the digital combiners, and only feeds back the digital combiners of each antenna array-user pair to the related user terminals. Thus, a low complexity user architecture is sufficient to achieve a higher performance. The developed optimization framework for the energy efficiency jointly optimizes the number of served users and the total transmit power by utilizing the derived upper bound of the achievable rate. The proposed transceiver architectures provide a more energy-efficient system model compared to the hybrid systems in which the spatial modulation technique is not exploited. This thesis develops low-complexity system models that operate in narrowband and wideband channel environments to meet the energy and spectrum efficiency demands of future wireless networks. It is corroborated in the thesis that adopting index modulation techniques both in the systems improves the system performance in various aspects.:1 Introduction 1 1.1 Motivation 1 1.2 Overview and Contribution 2 1.3 Outline 9 2 Preliminaries and Fundamentals 13 2.1 Multicarrier Systems 13 2.2 Large-scale Multiple Input Multiple Output Systems 17 2.3 Index Modulation Techniques 19 2.4 Single Cell Multiuser Networks 22 3 Multicarrier Systems with Index Modulation 27 3.1 Orthogonal Frequency Division Multiplexing 28 3.2 Generalized Frequency Division Multiplexing 40 3.3 Summary 52 4 Hybrid Beamforming with Spatial Modulation 55 4.1 Uplink Transmission 56 4.2 Downlink Transmission 74 4.3 Summary 106 5 Conclusion and Outlook 109 5.1 Conclusion 109 5.2 Outlook 111 A Quantization Error Derivations 113 B On the Achievable Rate of Gaussian Mixtures 115 B.1 The Conditional Density Function 115 B.2 Tight Bounds on the Differential Entropy 116 B.3 A Bound on the Achievable Rate 118 C Multiuser MIMO Downlink without Spatial Modulation 121 Bibliograph

Reliability of Trigonometric Transform-based Multi-Carrier Scheme

This work is looking for a new physical layer of a multi-carrier wireless communication system to be implemented in low complexity way, resorting to suitable fast transform. The work presents and assesses a scheme based on Discrete Trigonometric Transform with appending symmetric redundancy either in each or multiple consecutive transformed blocks. A receiver front-end filter is proposed to enforce whole symmetry in the channel impulse response, and bank of one tap filter per sub-carrier is applied as an equalizer in the transform domain. The behaviour of the transceiver is studied in the context of practical impairments like fading channel, carrier frequency offset and narrow band interference. Moreover, the performance is evaluated in contrast with the state of art methods by means of computer simulations, and it has been found that the new scheme improves robustness and reliability of communication signal, and record lower peak to average power ratio. The study demonstrates that front-end matched filter effectively performs frequency synchronization to compensate the carrier frequency offset in the received signal