26 research outputs found

    An efficient logic fault diagnosis framework based on effect-cause approach

    Get PDF
    Fault diagnosis plays an important role in improving the circuit design process and the manufacturing yield. With the increasing number of gates in modern circuits, determining the source of failure in a defective circuit is becoming more and more challenging. In this research, we present an efficient effect-cause diagnosis framework for combinational VLSI circuits. The framework consists of three stages to obtain an accurate and reasonably precise diagnosis. First, an improved critical path tracing algorithm is proposed to identify an initial suspect list by backtracing from faulty primary outputs toward primary inputs. Compared to the traditional critical path tracing approach, our algorithm is faster and exact. Second, a novel probabilistic ranking model is applied to rank the suspects so that the most suspicious one will be ranked at or near the top. Several fast filtering methods are used to prune unrelated suspects. Finally, to refine the diagnosis, fault simulation is performed on the top suspect nets using several common fault models. The difference between the observed faulty behavior and the simulated behavior is used to rank each suspect. Experimental results on ISCAS85 benchmark circuits show that this diagnosis approach is efficient both in terms of memory space and CPU time and the diagnosis results are accurate and reasonably precise

    Modelling and Test Generation for Crosstalk Faults in DSM Chips

    Get PDF
    In the era of deep submicron technology (DSM), many System-on-Chip (SoC) applications require the components to be operating at high clock speeds. With the shrinking feature size and ever increasing clock frequencies, the DSM technology has led to a well-known problem of Signal Integrity (SI) more especially in the connecting layout design. The increasing aspect ratios of metal wires and also the ratio of coupling capacitance over substrate capacitance result in electrical coupling of interconnects which leads to crosstalk problems. In this thesis, first the work carried out to model the crosstalk behaviour between aggressor and victim by considering the distributed RLGC parameters of interconnect and the coupling capacitance and mutual conductance between the two nets is presented. The proposed model also considers the RC linear models of the CMOS drivers and receivers. The behaviour of crosstalk in case of under etching problem has been studied and modelled by distributing and approximating the defect behaviour throughout the nets. Next, the proposed model has also been extended to model the behaviour of crosstalk in case of one victim is influenced by several aggressors by considering all aggressors have similar effect (worst-case) on victim. In all the above cases simulation experiments were also carried out and compared with well-known circuit simulation tool PSPICE. It has been proved that the generated crosstalk model is faster and the results generated are within 10% of error margin compared to latter simulation tool. Because of the accuracy and speed of the proposed model, the model is very useful for both SoC designers and test engineers to analyse the crosstalk behaviour. Each manufactured device needs to be tested thoroughly to ensure the functionality before its delivery. The test pattern generation for crosstalk faults is also necessary to test the corresponding crosstalk faults. In this thesis, the well-known PODEM algorithm for stuck-at faults is extended to generate the test patterns for crosstalk faults between single aggressor and single victim. To apply modified PODEM for crosstalk faults, the transition behaviour has been divided into two logic parts as before transition and after transition. After finding individually required test patterns for before transition and after transition, the generated logic vectors are appended to create transition test patterns for crosstalk faults. The developed algorithm is also applied for a few ISCAS 85 benchmark circuits and the fault coverage is found excellent in most circuits. With the incorporation of proposed algorithm into the ATPG tools, the efficiency of testing will be improved by generating the test patterns for crosstalk faults besides for the conventional stuck-at faults. In generating test patterns for crosstalk faults on single victim due to multiple aggressors, the modified PODEM algorithm is found to be more time consuming. The search capability of Genetic Algorithms in finding the required combination of several input factors for any optimized problem fascinated to apply GA for generating test patterns as generating the test pattern is also similar to finding the required vector out of several input transitions. Initially the GA is applied for generating test patterns for stuck-at faults and compared the results with PODEM algorithm. As the fault coverage is almost similar to the deterministic algorithm PODEM, the GA developed for stuck-at faults is extended to find test patterns for crosstalk faults between single aggressor and single victim. The elitist GA is also applied for a few ISCAS 85 benchmark circuits. Later the algorithm is extended to generate test patterns for worst-case crosstalk faults. It has been proved that elitist GA developed in this thesis is also very useful in generating test patterns for crosstalk faults especially for multiple aggressor and single victim crosstalk faults

    Fault modelling and accelerated simulation of integrated circuits manufacturing defects under process variation

    No full text
    As silicon manufacturing process scales to and beyond the 65-nm node, process variation can no longer be ignored. The impact of process variation on integrated circuit performance and power has received significant research input. Variation-aware test, on the other hand, is a relatively new research area that is currently receiving attention worldwide.Research has shown that test without considering process variation may lead to loss of test quality. Fault modelling and simulation serve as a backbone of manufacturing test. This thesis is concerned with developing efficient fault modelling techniques and simulation methodologies that take into account the effect of process variation on manufacturing defects with particular emphasis on resistive bridges and resistive opens.The first contribution of this thesis addresses the problem of long computation time required to generate logic fault of resistive bridges under process variation by developing a fast and accurate modelling technique to model logic fault behaviour of resistive bridges.The new technique is implemented by employing two efficient voltage calculation algorithms to calculate the logic threshold voltage of driven gates and critical resistance of a fault-site to enable the computation of bridge logic faults without using SPICE. Simulation results show that the technique is fast (on average 53 times faster) and accurate (worst case is 2.64% error) when compared with HSPICE. The second contribution analyses the complexity of delay fault simulation of resistive bridges to reduce the computation time of delay fault when considering process variation. An accelerated delay fault simulation methodology of resistive bridges is developed by employing a three-step strategy to speed up the calculation of transient gate output voltage which is needed to accurately compute delay faults. Simulation results show that the methodology is on average 17.4 times faster, with 5.2% error in accuracy, when compared with HSPICE. The final contribution presents an accelerated simulation methodology of resistive opens to address the problem of long simulation time of delay fault when considering process variation. The methodology is implemented by using two efficient algorithms to accelerate the computation of transient gate output voltage and timing critical resistance of an open fault-site. Simulation results show that the methodology is on average up to 52 times faster than HSPICE, with 4.2% error in accuracy

    Multi-level simulation of nano-electronic digital circuits on GPUs

    Get PDF
    Simulation of circuits and faults is an essential part in design and test validation tasks of contemporary nano-electronic digital integrated CMOS circuits. Shrinking technology processes with smaller feature sizes and strict performance and reliability requirements demand not only detailed validation of the functional properties of a design, but also accurate validation of non-functional aspects including the timing behavior. However, due to the rising complexity of the circuit behavior and the steady growth of the designs with respect to the transistor count, timing-accurate simulation of current designs requires a lot of computational effort which can only be handled by proper abstraction and a high degree of parallelization. This work presents a simulation model for scalable and accurate timing simulation of digital circuits on data-parallel graphics processing unit (GPU) accelerators. By providing compact modeling and data-structures as well as through exploiting multiple dimensions of parallelism, the simulation model enables not only fast and timing-accurate simulation at logic level, but also massively-parallel simulation with switch level accuracy. The model facilitates extensions for fast and efficient fault simulation of small delay faults at logic level, as well as first-order parametric and parasitic faults at switch level. With the parallelization on GPUs, detailed and scalable simulation is enabled that is applicable even to multi-million gate designs. This way, comprehensive analyses of realistic timing-related faults in presence of process- and parameter variations are enabled for the first time. Additional simulation efficiency is achieved by merging the presented methods in a unified simulation model, that allows to combine the unique advantages of the different levels of abstraction in a mixed-abstraction multi-level simulation flow to reach even higher speedups. Experimental results show that the implemented parallel approach achieves unprecedented simulation throughput as well as high speedup compared to conventional timing simulators. The underlying model scales for multi-million gate designs and gives detailed insights into the timing behavior of digital CMOS circuits, thereby enabling large-scale applications to aid even highly complex design and test validation tasks

    Investigation into voltage and process variation-aware manufacturing test

    No full text
    Increasing integration and complexity in IC design provides challenges for manufacturing testing. This thesis studies how process and supply voltage variation influence defect behaviour to determine the impact on manufacturing test cost and quality. The focus is on logic testing of static CMOS designs with respect to two important defect types in deep submicron CMOS: resistive bridges and full opens. The first part of the thesis addresses testing for resistive bridge defects in designs with multiple supply voltage settings. To enable analysis, a fault simulator is developed using a supply voltage-aware model for bridge defect behaviour. The analysis shows that for high defect coverage it is necessary to perform test for more than one supply voltage setting, due to supply voltage-dependent behaviour. A low-cost and effective test method is presented consisting of multi-voltage test generation that achieves high defect coverage and test set size reduction without compromise to defect coverage. Experiments on synthesised benchmarks with realistic bridge locations validate the proposed method.The second part focuses on the behaviour of full open defects under supply voltage variation. The aim is to determine the appropriate value of supply voltage to use when testing. Two models are considered for the behaviour of full open defects with and without gate tunnelling leakage influence. Analysis of the supply voltage-dependent behaviour of full open defects is performed to determine if it is required to test using more than one supply voltage to detect all full open defects. Experiments on synthesised benchmarks using an extended version of the fault simulator tool mentioned above, measure the quantitative impact of supply voltage variation on defect coverage.The final part studies the impact of process variation on the behaviour of bridge defects. Detailed analysis using synthesised ISCAS benchmarks and realistic bridge model shows that process variation leads to additional faults. If process variation is not considered in test generation, the test will fail to detect some of these faults, which leads to test escapes. A novel metric to quantify the impact of process variation on test quality is employed in the development of a new test generation tool, which achieves high bridge defect coverage. The method achieves a user-specified test quality with test sets which are smaller than test sets generated without consideration of process variation

    Investigations into the feasibility of an on-line test methodology

    Get PDF
    This thesis aims to understand how information coding and the protocol that it supports can affect the characteristics of electronic circuits. More specifically, it investigates an on-line test methodology called IFIS (If it Fails It Stops) and its impact on the design, implementation and subsequent characteristics of circuits intended for application specific lC (ASIC) technology. The first study investigates the influences of information coding and protocol on the characteristics of IFIS systems. The second study investigates methods of circuit design applicable to IFIS cells and identifies the· technique possessing the characteristics most suitable for on-line testing. The third study investigates the characteristics of a 'real-life' commercial UART re-engineered using the techniques resulting from the previous two studies. The final study investigates the effects of the halting properties endowed by the protocol on failure diagnosis within IFIS systems. The outcome of this work is an identification and characterisation of the factors that influence behaviour, implementation costs and the ability to test and diagnose IFIS designs

    Energy-Efficient Digital Circuit Design using Threshold Logic Gates

    Get PDF
    abstract: Improving energy efficiency has always been the prime objective of the custom and automated digital circuit design techniques. As a result, a multitude of methods to reduce power without sacrificing performance have been proposed. However, as the field of design automation has matured over the last few decades, there have been no new automated design techniques, that can provide considerable improvements in circuit power, leakage and area. Although emerging nano-devices are expected to replace the existing MOSFET devices, they are far from being as mature as semiconductor devices and their full potential and promises are many years away from being practical. The research described in this dissertation consists of four main parts. First is a new circuit architecture of a differential threshold logic flipflop called PNAND. The PNAND gate is an edge-triggered multi-input sequential cell whose next state function is a threshold function of its inputs. Second a new approach, called hybridization, that replaces flipflops and parts of their logic cones with PNAND cells is described. The resulting \hybrid circuit, which consists of conventional logic cells and PNANDs, is shown to have significantly less power consumption, smaller area, less standby power and less power variation. Third, a new architecture of a field programmable array, called field programmable threshold logic array (FPTLA), in which the standard lookup table (LUT) is replaced by a PNAND is described. The FPTLA is shown to have as much as 50% lower energy-delay product compared to conventional FPGA using well known FPGA modeling tool called VPR. Fourth, a novel clock skewing technique that makes use of the completion detection feature of the differential mode flipflops is described. This clock skewing method improves the area and power of the ASIC circuits by increasing slack on timing paths. An additional advantage of this method is the elimination of hold time violation on given short paths. Several circuit design methodologies such as retiming and asynchronous circuit design can use the proposed threshold logic gate effectively. Therefore, the use of threshold logic flipflops in conventional design methodologies opens new avenues of research towards more energy-efficient circuits.Dissertation/ThesisDoctoral Dissertation Computer Science 201

    Testability and redundancy techniques for improved yield and reliability of CMOS VLSI circuits

    Get PDF
    The research presented in this thesis is concerned with the design of fault-tolerant integrated circuits as a contribution to the design of fault-tolerant systems. The economical manufacture of very large area ICs will necessitate the incorporation of fault-tolerance features which are routinely employed in current high density dynamic random access memories. Furthermore, the growing use of ICs in safety-critical applications and/or hostile environments in addition to the prospect of single-chip systems will mandate the use of fault-tolerance for improved reliability. A fault-tolerant IC must be able to detect and correct all possible faults that may affect its operation. The ability of a chip to detect its own faults is not only necessary for fault-tolerance, but it is also regarded as the ultimate solution to the problem of testing. Off-line periodic testing is selected for this research because it achieves better coverage of physical faults and it requires less extra hardware than on-line error detection techniques. Tests for CMOS stuck-open faults are shown to detect all other faults. Simple test sequence generation procedures for the detection of all faults are derived. The test sequences generated by these procedures produce a trivial output, thereby, greatly simplifying the task of test response analysis. A further advantage of the proposed test generation procedures is that they do not require the enumeration of faults. The implementation of built-in self-test is considered and it is shown that the hardware overhead is comparable to that associated with pseudo-random and pseudo-exhaustive techniques while achieving a much higher fault coverage through-the use of the proposed test generation procedures. The consideration of the problem of testing the test circuitry led to the conclusion that complete test coverage may be achieved if separate chips cooperate in testing each other's untested parts. An alternative approach towards complete test coverage would be to design the test circuitry so that it is as distributed as possible and so that it is tested as it performs its function. Fault correction relies on the provision of spare units and a means of reconfiguring the circuit so that the faulty units are discarded. This raises the question of what is the optimum size of a unit? A mathematical model, linking yield and reliability is therefore developed to answer such a question and also to study the effects of such parameters as the amount of redundancy, the size of the additional circuitry required for testing and reconfiguration, and the effect of periodic testing on reliability. The stringent requirement on the size of the reconfiguration logic is illustrated by the application of the model to a typical example. Another important result concerns the effect of periodic testing on reliability. It is shown that periodic off-line testing can achieve approximately the same level of reliability as on-line testing, even when the time between tests is many hundreds of hours

    Driving the Network-on-Chip Revolution to Remove the Interconnect Bottleneck in Nanoscale Multi-Processor Systems-on-Chip

    Get PDF
    The sustained demand for faster, more powerful chips has been met by the availability of chip manufacturing processes allowing for the integration of increasing numbers of computation units onto a single die. The resulting outcome, especially in the embedded domain, has often been called SYSTEM-ON-CHIP (SoC) or MULTI-PROCESSOR SYSTEM-ON-CHIP (MP-SoC). MPSoC design brings to the foreground a large number of challenges, one of the most prominent of which is the design of the chip interconnection. With a number of on-chip blocks presently ranging in the tens, and quickly approaching the hundreds, the novel issue of how to best provide on-chip communication resources is clearly felt. NETWORKS-ON-CHIPS (NoCs) are the most comprehensive and scalable answer to this design concern. By bringing large-scale networking concepts to the on-chip domain, they guarantee a structured answer to present and future communication requirements. The point-to-point connection and packet switching paradigms they involve are also of great help in minimizing wiring overhead and physical routing issues. However, as with any technology of recent inception, NoC design is still an evolving discipline. Several main areas of interest require deep investigation for NoCs to become viable solutions: • The design of the NoC architecture needs to strike the best tradeoff among performance, features and the tight area and power constraints of the onchip domain. • Simulation and verification infrastructure must be put in place to explore, validate and optimize the NoC performance. • NoCs offer a huge design space, thanks to their extreme customizability in terms of topology and architectural parameters. Design tools are needed to prune this space and pick the best solutions. • Even more so given their global, distributed nature, it is essential to evaluate the physical implementation of NoCs to evaluate their suitability for next-generation designs and their area and power costs. This dissertation performs a design space exploration of network-on-chip architectures, in order to point-out the trade-offs associated with the design of each individual network building blocks and with the design of network topology overall. The design space exploration is preceded by a comparative analysis of state-of-the-art interconnect fabrics with themselves and with early networkon- chip prototypes. The ultimate objective is to point out the key advantages that NoC realizations provide with respect to state-of-the-art communication infrastructures and to point out the challenges that lie ahead in order to make this new interconnect technology come true. Among these latter, technologyrelated challenges are emerging that call for dedicated design techniques at all levels of the design hierarchy. In particular, leakage power dissipation, containment of process variations and of their effects. The achievement of the above objectives was enabled by means of a NoC simulation environment for cycleaccurate modelling and simulation and by means of a back-end facility for the study of NoC physical implementation effects. Overall, all the results provided by this work have been validated on actual silicon layout
    corecore