Fast, Accurate and Detailed NoC Simulations

Network-on-Chip (NoC) architectures have a wide variety of parameters that can be adapted to the designer's requirements. Fast exploration of this parameter space is only possible at a high-level and several methods have been proposed. Cycle and bit accurate simulation is necessary when the actual router's RTL description needs to be evaluated and verified. However, extensive simulation of the NoC architecture with cycle and bit accuracy is prohibitively time consuming. In this paper we describe a simulation method to simulate large parallel homogeneous and heterogeneous network-on-chips on a single FPGA. The method is especially suitable for parallel systems where lengthy cycle and bit accurate simulations are required. As a case study, we use a NoC that was modelled and simulated in SystemC. We simulate the same NoC on the described FPGA simulator. This enables us to observe the NoC behavior under a large variety of traffic patterns. Compared with the SystemC simulation we achieved a speed-up of 80-300, without compromising the cycle and bit level accuracy

Experimental Evaluation and Comparison of Time-Multiplexed Multi-FPGA Routing Architectures

Emulating large complex designs require multi-FPGA systems (MFS). However, inter-FPGA communication is confronted by the challenge of lack of interconnect capacity due to limited number of FPGA input/output (I/O) pins. Serializing parallel signals onto a single trace effectively addresses the limited I/O pin obstacle. Besides the multiplexing scheme and multiplexing ratio (number of inter-FPGA signals per trace), the choice of the MFS routing architecture also affect the critical path latency. The routing architecture of an MFS is the interconnection pattern of FPGAs, fixed wires and/or programmable interconnect chips. Performance of existing MFS routing architectures is also limited by off-chip interface selection. In this dissertation we proposed novel 2D and 3D latency-optimized time-multiplexed MFS routing architectures. We used rigorous experimental approach and real sequential benchmark circuits to evaluate and compare the proposed and existing MFS routing architectures. This research provides a new insight into the encouraging effects of using off-chip optical interface and three dimensional MFS routing architectures. The vertical stacking results in shorter off-chip links improving the overall system frequency with the additional advantage of smaller footprint area. The proposed 3D architectures employed serialized interconnect between intra-plane and inter-plane FPGAs to address the pin limitation problem. Additionally, all off-chip links are replaced by optical fibers that exhibited latency improvement and resulted in faster MFS. Results indicated that exploiting third dimension provided latency and area improvements as compared to 2D MFS. We also proposed latency-optimized planar 2D MFS architectures in which electrical interconnections are replaced by optical interface in same spatial distribution. Performance evaluation and comparison showed that the proposed architectures have reduced critical path delay and system frequency improvement as compared to conventional MFS. We also experimentally evaluated and compared the system performance of three inter-FPGA communication schemes i.e. Logic Multiplexing, SERDES and MGT in conjunction with two routing architectures i.e. Completely Connected Graph (CCG) and TORUS. Experimental results showed that SERDES attained maximum frequency than the other two schemes. However, for very high multiplexing ratios, the performance of SERDES & MGT became comparable

NoC Emulation based on Partial Reconfiguration

This paper studies the possibly of using partial reconfiguration for achieving acceleration of the emulation process of Systems on Chip based on Networks on Chip (NoC). The main advantage of using partial reconfiguration is that re-synthesis of the systems is not required and thus the emulation process can be accelerated. The paper focuses on the description of a method for building partial runtime reconfigurable systems and its application for building a NoC emulation framework. The paper also includes a brief description of all the building elements of the emulation framework and a use case that demonstrates the advantages of the use of partial reconfiguration for emulation

Speeding-up model-based fault injection of deep-submicron CMOS fault models through dynamic and partially reconfigurable FPGAS

Actualmente, las tecnologías CMOS submicrónicas son básicas para el desarrollo de los modernos sistemas basados en computadores, cuyo uso simplifica enormemente nuestra vida diaria en una gran variedad de entornos, como el gobierno, comercio y banca electrónicos, y el transporte terrestre y aeroespacial. La continua reducción del tamaño de los transistores ha permitido reducir su consumo y aumentar su frecuencia de funcionamiento, obteniendo por ello un mayor rendimiento global. Sin embargo, estas mismas características que mejoran el rendimiento del sistema, afectan negativamente a su confiabilidad. El uso de transistores de tamaño reducido, bajo consumo y alta velocidad, está incrementando la diversidad de fallos que pueden afectar al sistema y su probabilidad de aparición. Por lo tanto, existe un gran interés en desarrollar nuevas y eficientes técnicas para evaluar la confiabilidad, en presencia de fallos, de sistemas fabricados mediante tecnologías submicrónicas. Este problema puede abordarse por medio de la introducción deliberada de fallos en el sistema, técnica conocida como inyección de fallos. En este contexto, la inyección basada en modelos resulta muy interesante, ya que permite evaluar la confiabilidad del sistema en las primeras etapas de su ciclo de desarrollo, reduciendo por tanto el coste asociado a la corrección de errores. Sin embargo, el tiempo de simulación de modelos grandes y complejos imposibilita su aplicación en un gran número de ocasiones. Esta tesis se centra en el uso de dispositivos lógicos programables de tipo FPGA (Field-Programmable Gate Arrays) para acelerar los experimentos de inyección de fallos basados en simulación por medio de su implementación en hardware reconfigurable. Para ello, se extiende la investigación existente en inyección de fallos basada en FPGA en dos direcciones distintas: i) se realiza un estudio de las tecnologías submicrónicas existentes para obtener un conjunto representativo de modelos de fallos transitoriosAndrés Martínez, DD. (2007). Speeding-up model-based fault injection of deep-submicron CMOS fault models through dynamic and partially reconfigurable FPGAS [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/1943Palanci

Heracles: Fully Synthesizable Parameterized MIPS-Based Multicore System

Heracles is an open-source complete multicore system written in Verilog. It is fully parameterized and can be reconfigured and synthesized into different topologies and sizes. Each processing node has a 7-stage pipeline, fully bypassed, microprocessor running the MIPS-III ISA, a 4-stage input-buffer, virtual-channel router, and a local variable-size shared memory. Our design is highly modular with clear interfaces between the core, the memory hierarchy, and the on-chip network. In the baseline design, the microprocessor is attached to two caches, one instruction cache and one data cache, which are oblivious to the global memory organization. The memory system in Heracles can be configured as one single global shared memory (SM), or distributed shared memory (DSM), or any combination thereof. Each core is connected to the rest of the network of processors by a parameterized, realistic, wormhole router. We show different topology configurations of the system, and their synthesis results on the Xilinx Virtex-5 LX330T FPGA board. We also provide a small MIPS cross-compiler toolchain to assist in developing software for Heracles

Adaptation of High Performance and High Capacity Reconfigurable Systems to OpenCL Programming Environments

[EN] In this work, we adapt a reconfigurable computer system based on FPGA technologies to OpenCL programming environments. The reconfigurable system is part of a compute prototype of the MANGO European project that includes 96 FPGAs. To optimize the use and to obtain its maximum performance, it is essential to adapt it to heterogeneous systems programming environments such as OpenCL, which simplifies its programming. In this work, all the necessary activities for correct implementation of the software and hardware layer required for its use in OpenCL will be carried out, as well as an evaluation of the performance obtained and the flexibility offered by the solution provided. This work has been performed during an internship of 5 months. The internship is linked to an agreement between UPV and UniNa (Università degli Studi di Napoli Federico II).[ES] En este trabajo se va a realizar la adaptación de un sistema reconfigurable de cómputo basado en tecnologías de FPGAs hacia entornos de programación en OpenCL. El sistema reconfigurable forma parte de un prototipo de cálculo del proyecto Europeo MANGO que incluye 96 FPGAs. Con el fin de optimizar el uso y de obtener sus máximas prestaciones, se hace imprescindible una adaptación a entornos de programación de sistemas heterogéneos como OpenCL, lo cual simplifica su programación y uso. En este trabajo se realizarán todas las actividades necesarias para una correcta implementación de la capa software y hardware necesaria para su uso en OpenCL así como una evaluación de las prestaciones obtenidas y de la flexibilidad ofrecida por la solución aportada. Este trabajo se ha llevado a término durante una estancia de cinco meses en la Universitat Politécnica de Valéncia. Esta estancia está vinculada a un acuerdo entre la Universitat Politécnica de Valéncia y la Università degli Studi di Napoli Federico IIRusso, D. (2020). Adaptation of High Performance and High Capacity Reconfigurable Systems to OpenCL Programming Environments. http://hdl.handle.net/10251/150393TFG

Radiation Mitigation and Power Optimization Design Tools for Reconfigurable Hardware in Orbit

The Reconfigurable Hardware in Orbit (RHinO)project is focused on creating a set of design tools that facilitate and automate design techniques for reconfigurable computing in space, using SRAM-based field-programmable-gate-array (FPGA) technology. In the second year of the project, design tools that leverage an established FPGA design environment have been created to visualize and analyze an FPGA circuit for radiation weaknesses and power inefficiencies. For radiation, a single event Upset (SEU) emulator, persistence analysis tool, and a half-latch removal tool for Xilinx/Virtex-II devices have been created. Research is underway on a persistence mitigation tool and multiple bit upsets (MBU) studies. For power, synthesis level dynamic power visualization and analysis tools have been completed. Power optimization tools are under development and preliminary test results are positive

Reconfigurable Architectures and Systems for IoT Applications

abstract: Internet of Things (IoT) has become a popular topic in industry over the recent years, which describes an ecosystem of internet-connected devices or things that enrich the everyday life by improving our productivity and efficiency. The primary components of the IoT ecosystem are hardware, software and services. While the software and services of IoT system focus on data collection and processing to make decisions, the underlying hardware is responsible for sensing the information, preprocess and transmit it to the servers. Since the IoT ecosystem is still in infancy, there is a great need for rapid prototyping platforms that would help accelerate the hardware design process. However, depending on the target IoT application, different sensors are required to sense the signals such as heart-rate, temperature, pressure, acceleration, etc., and there is a great need for reconfigurable platforms that can prototype different sensor interfacing circuits. This thesis primarily focuses on two important hardware aspects of an IoT system: (a) an FPAA based reconfigurable sensing front-end system and (b) an FPGA based reconfigurable processing system. To enable reconfiguration capability for any sensor type, Programmable ANalog Device Array (PANDA), a transistor-level analog reconfigurable platform is proposed. CAD tools required for implementation of front-end circuits on the platform are also developed. To demonstrate the capability of the platform on silicon, a small-scale array of 24×25 PANDA cells is fabricated in 65nm technology. Several analog circuit building blocks including amplifiers, bias circuits and filters are prototyped on the platform, which demonstrates the effectiveness of the platform for rapid prototyping IoT sensor interfaces. IoT systems typically use machine learning algorithms that run on the servers to process the data in order to make decisions. Recently, embedded processors are being used to preprocess the data at the energy-constrained sensor node or at IoT gateway, which saves considerable energy for transmission and bandwidth. Using conventional CPU based systems for implementing the machine learning algorithms is not energy-efficient. Hence an FPGA based hardware accelerator is proposed and an optimization methodology is developed to maximize throughput of any convolutional neural network (CNN) based machine learning algorithm on a resource-constrained FPGA.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201