Advances in Control of Power Electronic Converters

This book proposes a list of contributions in the field of control of power electronics converters for different topologies: DC-DC, DC-AC and AC-DC. It particularly focuses on the use of different advanced control techniques with the aim of improving the performances, flexibility and efficiency in the context of several operation conditions. Sliding mode control, fuzzy logic based control, dead time compensation and optimal linear control are among the techniques developed in the special issue. Simulation and experimental results are provided by the authors to validate the proposed control strategies

AVERAGE-VALUE MODELING OF HYSTERESIS CURRENT CONTROL IN POWER ELECTRONICS

Hysteresis current control has been widely used in power electronics with the advantages of fast dynamic response under parameter, line and load variation and ensured stability. However, a main disadvantage of hysteresis current control is the uncertain and varying switching frequency which makes it difficult to form an average-value model. The changing switching frequency and unspecified switching duty cycle make conventional average-value models based on PWM control difficult to apply directly to converters that are controlled by hysteresis current control. In this work, a new method for average-value modeling of hysteresis current control in boost converters, three-phase inverters, and brushless dc motor drives is proposed. It incorporates a slew-rate limitation on the inductor current that occurs naturally in the circuit during large system transients. This new method is compared with existing methods in terms of simulation run time and rms error. The performance is evaluated based on a variety of scenarios, and the simulation results are compared with the results of detailed models. The simulation results show that the proposed model represents the detailed model well and is faster and more accurate than existing methods. The slew-rate limitation model of hysteresis current control accurately captures the salient detail of converter performance while maintaining the computational efficiency of average-value models. Validations in hardware are also presented

Design and Control of Power Converters 2019

In this book, 20 papers focused on different fields of power electronics are gathered. Approximately half of the papers are focused on different control issues and techniques, ranging from the computer-aided design of digital compensators to more specific approaches such as fuzzy or sliding control techniques. The rest of the papers are focused on the design of novel topologies. The fields in which these controls and topologies are applied are varied: MMCs, photovoltaic systems, supercapacitors and traction systems, LEDs, wireless power transfer, etc

Conversión de Potencia para un Sistema de Almacenamiento Híbrido Batería-Capacitor

Context: Thanks to the low emissions of CO2 generated by electric systems, those solutions have anincreased attention from industry and academia. However, the electrical storage systems required in alarge amount of applications must to have both high energy and power densities. Method: To meet those requirements, this paper proposes an active hybrid energy storage system(HESS), which is formed by a battery, i.e. the device with high energy density, and a capacitor, i.e. the device with high power capability. The proposed power system also protects the battery by limiting the current derivative. Results: Two sliding-mode controllers (SMC) are designed to regulate both the battery current and the load voltage. The design process guarantees the global stability and safe battery operation. Conclusions: The controller avoids the battery degradation caused by the high-frequency current components since the capacitor assumes those components demanded by the load profile.Contexto: Gracias a las bajas emisiones de CO2 de los sistemas el´ectricos, estos han ganado mucha atenci´on por parte de la industria y la academia. Sin embargo, los sistemas de almacenamiento de energ´ıa requeridos en un sin numero de aplicaciones deben garantizar ser de alta densidad de energ´ıa y potencia. M´etodo: Para satisfacer estos requerimientos, este trabajo propone un sistema de almacenamiento de energ´ıa h´ıbrido (HESS) activo, el cual es formado por una bater´ıa como dispositivo de alta densidad de energ´ıa, y un capacitor como el dispositivo de alta densidad de potencia. Asimismo, la soluci´on propuesta protege la bater´ı a trav´es de la limitaci´on de la derivada de la corriente. Resultados: Se dise˜nan dos controladores por modos deslizantes, uno para la corriente de la bater´ıa y otro para regular el voltaje en la carga. El proceso de dise˜no garantiza la estabilidad global del sistema y una operaci´on segura de la bater´ıa

Development of controllers using FPGA for fuel cells in standalone and utility applications

In the recent years, increase in consumption of energy, instability of crude oil price and global climate change has forced researchers to focus more on renewable energy sources.Though there are different renewable energy sources available (such as photovoltaic and wind energy), they have some major limitations. The potential techniques which can provide renewable energy are fuel cell technology which is better than other renewable sources of energy. Solid oxide fuel cell (SOFC) is more efficient, environmental friendly renewable energy source. This dissertation focuses on load/grid connected fuel cell power system (FCPS) which can be used as a backup power source for household and commercial units. This backup power source will be efficient and will provide energy at an affordable per unit cost. Load/grid connected fuel cell power system mainly comprises of a fuel cell module, DCDC converter and DC-AC inverter. This thesis primarily focuses on solid oxide fuel cell (SOFC) modelling, digital control of DC-DC converter and DC-AC inverter. Extensive simulation results are validated by experimental results. Dynamic mathematical model of SOFC is developed to find out output voltage, efficiency, over potential loss and power density of fuel cell stack. The output voltage of fuel cell is fed to a DC-DC converter to step up the output voltage. Conventional Proportional-Integral (PI) controller and FPGA based PI controller is implemented and experimentally validated. The output voltage of DC-DC converter is fed to DC-AC inverter. Different pulse width modulation-voltage source inverter (PWM-VSI) control strategy (such as Hysteresis Current Controller (HCC), Adaptive-HCC, Fuzzy-HCC, Adaptive Fuzzy-HCC, Triangular Carrier Current Controller (TCCC) and Triangular Periodical Current Controller (TPCC)) for DC-AC inverter are investigated and validated through extensive simulations using MATLAB/SIMULINK. This work also focuses on number of fuel cells required for application in real time and remedy strategies when one or few fuel cells are malfunctioning. When the required numbers of fuel cells are not available, DC-DC converter is used to step up the output voltage of fuel cell. When there is a malfunction in fuel cell or shortage of hydrogen then a battery is used to provide backup power

Analysis And Design Optimization Of Multiphase Converter

Future microprocessors pose many challenges to the power conversion techniques. Multiphase synchronous buck converters have been widely used in high current low voltage microprocessor application. Design optimization needs to be carefully carried out with pushing the envelope specification and ever increasing concentration towards power saving features. In this work, attention has been focused on dynamic aspects of multiphase synchronous buck design. The power related issues and optimizations have been comprehensively investigated in this paper. In the first chapter, multiphase DC-DC conversion is presented with background application. Adaptive voltage positioning and various nonlinear control schemes are evaluated. Design optimization are presented to achieve best static efficiency over the entire load range. Power loss analysis from various operation modes and driver IC definition are studied thoroughly to better understand the loss terms and minimize the power loss. Load adaptive control is then proposed together with parametric optimization to achieve optimum efficiency figure. New nonlinear control schemes are proposed to improve the transient response, i.e. load engage and load release responses, of the multiphase VR in low frequency repetitive transient. Drop phase optimization and PWM transition from long tri-state phase are presented to improve the smoothness and robustness of the VR in mode transition. During high frequency repetitive transient, the control loop should be optimized and nonlinear loop should be turned off. Dynamic current sharing are thoroughly studied in chapter 4. The output impedance of the multiphase v synchronous buck are derived to assist the analysis. Beat frequency is studied and mitigated by proposing load frequency detection scheme by turning OFF the nonlinear loop and introducing current protection in the control loop. Dynamic voltage scaling (DVS) is now used in modern Multi-Core processor (MCP) and multiprocessor System-on-Chip (MPSoC) to reduce operational voltage under light load condition. With the aggressive motivation to boost dynamic power efficiency, the design specification of voltage transition (dv/dt) for the DVS is pushing the physical limitation of the multiphase converter design and the component stress as well. In this paper, the operation modes and modes transition during dynamic voltage transition are illustrated. Critical dead-times of driver IC design and system dynamics are first studied and then optimized. The excessive stress on the control MOSFET which increases the reliability concern is captured in boost mode operation. Feasible solutions are also proposed and verified by both simulation and experiment results. CdV/dt compensation for removing the AVP effect and novel nonlinear control scheme for smooth transition are proposed for dealing with fast voltage positioning. Optimum phase number control during dynamic voltage transition is also proposed and triggered by voltage identification (VID) delta to further reduce the dynamic loss. The proposed schemes are experimentally verified in a 200 W six phase synchronous buck converter. Finally, the work is concluded. The references are listed

Controlador no-lineal para sistemas de almacenamiento con voltaje de salida regulado y derivada de corriente segura para la batería

This paper proposes a non-linear control structure for a hybrid energy storage system with a series architecture, which regulates the voltage of a DC bus (output voltage) and ensures that the battery current fulfills the current slew-rate restriction. The proposed solution has two stages, in the first one, the battery is connected to a buck/boost converter that feeds an auxiliary capacitor. In the second stage, the auxiliary capacitor is connected to a DC bus through a second buck/boost converter. Both converters are regulated using cascaded control systems, where the inner loops are slidingmode controllers of the inductors’ current, and the outer loops in the first and second converter are designed to limit the slew-rate of the battery current and to regulate the dc bus voltage, respectively. The paper provides the design procedure for the controllers and validates its performance with simulation results for the power system operating in charging, discharging and stand-by modes.Este artículo propone una estructura de control no-lineal para un sistema de almacenamiento híbrido con una arquitectura en serie, en la cual se regula la tensión de un bus DC (voltaje de salida) y asegura que la corriente de la batería cumpla con la restricción de velocidad de cambio en la corriente. La solución propuesta tiene dos etapas, en la primera se conecta una batería a un convertidor buck/boost que alimenta un capacitor auxiliar. En la segunda etapa, el capacitor auxiliar se conecta a un bus de DC a través de un segundo convertidor buck/boost. Ambos convertidores se regulan utilizando sistemas de control en cascada, donde los lazos internos son controladores por modos deslizantes de las corrientes de los inductores, y los lazos externos del primer y el segundo convertidor se diseñan para limitar la velocidad de cambio de la corriente en la batería y regular la tensión en el bus de DC, respectivamente. El artículo proporciona el procedimiento de diseño para los controladores y valida su desempeño con resultados de simulación considerando el sistema de potencia operando en modos de carga, descarga y almacenamiento

Emerging Power Electronics Technologies for Sustainable Energy Conversion

This Special Issue summarizes, in a single reference, timely emerging topics related to power electronics for sustainable energy conversion. Furthermore, at the same time, it provides the reader with valuable information related to open research opportunity niches

Emerging Power Electronics Technologies for Sustainable Energy Conversion

This Special Issue summarizes, in a single reference, timely emerging topics related to power electronics for sustainable energy conversion. Furthermore, at the same time, it provides the reader with valuable information related to open research opportunity niches

Power Management ICs for Internet of Things, Energy Harvesting and Biomedical Devices

This dissertation focuses on the power management unit (PMU) and integrated circuits (ICs) for the internet of things (IoT), energy harvesting and biomedical devices. Three monolithic power harvesting methods are studied for different challenges of smart nodes of IoT networks. Firstly, we propose that an impedance tuning approach is implemented with a capacitor value modulation to eliminate the quiescent power consumption. Secondly, we develop a hill-climbing MPPT mechanism that reuses and processes the information of the hysteresis controller in the time-domain and is free of power hungry analog circuits. Furthermore, the typical power-performance tradeoff of the hysteresis controller is solved by a self-triggered one-shot mechanism. Thus, the output regulation achieves high-performance and yet low-power operations as low as 12 µW. Thirdly, we introduce a reconfigurable charge pump to provide the hybrid conversion ratios (CRs) as 1⅓× up to 8× for minimizing the charge redistribution loss. The reconfigurable feature also dynamically tunes to maximum power point tracking (MPPT) with the frequency modulation, resulting in a two-dimensional MPPT. Therefore, the voltage conversion efficiency (VCE) and the power conversion efficiency (PCE) are enhanced and flattened across a wide harvesting range as 0.45 to 3 V. In a conclusion, we successfully develop an energy harvesting method for the IoT smart nodes with lower cost, smaller size, higher conversion efficiency, and better applicability. For the biomedical devices, this dissertation presents a novel cost-effective automatic resonance tracking method with maximum power transfer (MPT) for piezoelectric transducers (PT). The proposed tracking method is based on a band-pass filter (BPF) oscillator, exploiting the PT’s intrinsic resonance point through a sensing bridge. It guarantees automatic resonance tracking and maximum electrical power converted into mechanical motion regardless of process variations and environmental interferences. Thus, the proposed BPF oscillator-based scheme was designed for an ultrasonic vessel sealing and dissecting (UVSD) system. The sealing and dissecting functions were verified experimentally in chicken tissue and glycerin. Furthermore, a combined sensing scheme circuit allows multiple surgical tissue debulking, vessel sealer and dissector (VSD) technologies to operate from the same sensing scheme board. Its advantage is that a single driver controller could be used for both systems simplifying the complexity and design cost. In a conclusion, we successfully develop an ultrasonic scalpel to replace the other electrosurgical counterparts and the conventional scalpels with lower cost and better functionality