High Speed Test Interface Module Using MEMS Technology

With the transient frequency of available CMOS technologies exceeding hundreds of gigahertz and the increasing complexity of Integrated Circuit (IC) designs, it is now apparent that the architecture of current testers needs to be greatly improved to keep up with the formidable challenges ahead. Test requirements for modern integrated circuits are becoming more stringent, complex and costly. These requirements include an increasing number of test channels, higher test-speeds and enhanced measurement accuracy and resolution. In a conventional test configuration, the signal path from Automatic Test Equipment (ATE) to the Device-Under-Test (DUT) includes long traces of wires. At frequencies above a few gigahertz, testing integrated circuits becomes a challenging task. The effects on transmission lines become critical requiring impedance matching to minimize signal reflection. AC resistance due to the skin effect and electromagnetic coupling caused by radiation can also become important factors affecting the test results. In the design of a Device Interface Board (DIB), the greater the physical separation of the DUT and the ATE pin electronics, the greater the distortion and signal degradation. In this work, a new Test Interface Module (TIM) based on MEMS technology is proposed to reduce the distance between the tester and device-under-test by orders of magnitude. The proposed solution increases the bandwidth of test channels and reduces the undesired effects of transmission lines on the test results. The MEMS test interface includes a fixed socket and a removable socket. The removable socket incorporates MEMS contact springs to provide temporary with the DUT pads and the fixed socket contains a bed of micro-pins to establish electrical connections with the ATE pin electronics. The MEMS based contact springs have been modified to implement a high-density wafer level test probes for Through Silicon Vias (TSVs) in three dimensional integrated circuits (3D-IC). Prototypes have been fabricated using Silicon On Insulator SOI wafer. Experimental results indicate that the proposed architectures can operate up to 50 GHz without much loss or distortion. The MEMS probes can also maintain a good elastic performance without any damage or deformation in the test phase

Satellite power system: Concept development and evaluation program. Volume 3: Power transmission and reception. Technical summary and assessment

Efforts in the DOE/NASA concept development and evaluation program are discussed for the solar power satellite power transmission and reception system. A technical summary is provided together with a summary of system assessment activities. System options and system definition drivers are described. Major system assessment activities were in support of the reference system definition, solid state system studies, critical technology supporting investigations, and various system and subsystem tradeoffs. These activities are described together with reference system updates and alternative concepts for each of the subsystem areas. Conclusions reached as a result of the numerous analytical and experimental evaluations are presented. Remaining issues for a possible follow-on program are identified

Superconducting nanowire single-photon detectors: physics and applications

Single-photon detectors based on superconducting nanowires (SSPDs or SNSPDs) have rapidly emerged as a highly promising photon-counting technology for infrared wavelengths. These devices offer high efficiency, low dark counts and excellent timing resolution. In this review, we consider the basic SNSPD operating principle and models of device behaviour. We give an overview of the evolution of SNSPD device design and the improvements in performance which have been achieved. We also evaluate device limitations and noise mechanisms. We survey practical refrigeration technologies and optical coupling schemes for SNSPDs. Finally we summarize promising application areas, ranging from quantum cryptography to remote sensing. Our goal is to capture a detailed snapshot of an emerging superconducting detector technology on the threshold of maturity.Comment: 27 pages, 5 figures, Review article preprint versio

High-speed, low cost test platform using FPGA technology

The object of this research is to develop a low-cost, adaptable testing platform for multi-GHz digital applications, with concentration on the test requirement of advanced devices. Since most advanced ATEs are very expensive, this equipment is not always available for testing cost-sensitive devices. The approach is to use recently-introduced advanced FPGAs for the core logic of the testing platform, thereby allowing for a low-cost, low power-consumption, high-performance, and adaptable test system. Furthermore to customize the testing system for specific applications, we implemented multiple extension testing modules base on this platform. With these extension modules, new functions can be added easily and the test system can be upgraded with specific features required for other testing purposes. The applications of this platform can help those digital devices to be delivered into market with shorter time, lower cost and help the development of the whole industry.Ph.D

Wireless Testing of Integrated Circuits.

Integrated circuits (ICs) are usually tested during manufacture by means of automatic testing equipment (ATE) employing probe cards and needles that make repeated physical contact with the ICs under test. Such direct-contact probing is very costly and imposes limitations on the use of ATE. For example, the probe needles must be frequently cleaned or replaced, and some emerging technologies such as three-dimensional ICs cannot be probed at all. As an alternative to conventional probe-card testing, wireless testing has been proposed. It mitigates many of the foregoing problems by replacing probe needles and contact points with wireless communication circuits. However, wireless testing also raises new problems which are poorly understood such as: What is the most suitable wireless communication technique to employ, and how well does it work in practice? This dissertation addresses the design and implementation of circuits to support wireless testing of ICs. Various wireless testing methods are investigated and evaluated with respect to their practicality. The research focuses on near-field capacitive communication because of its efficiency over the very short ranges needed during IC manufacture. A new capacitive channel model including chip separation, cross-talk, and misalignment effects is proposed and validated using electro-magnetic simulation studies to provide the intuitions for efficient antenna and circuit design. We propose a compact clock and data recovery architecture to avoid a dedicated clock channel. An analytical model which predicts the DC-level fluctuation due to the capacitive channel is presented. Based on this model, feed-forward clock selection is designed to enhance performance. A method to select proper channel termination is discussed to maximize the channel efficiency for return-to-zero signaling. Two prototype ICs incorporating wireless testing systems were fabricated and tested with the proposed methods of testing digital circuits. Both successfully demonstrated gigahertz communication speeds with a bit-error rate less than 10^−11. A third prototype IC containing analog voltage measurement circuits was implemented to determine the feasibility of wirelessly testing analog circuits. The fabricated prototype achieved satisfactory voltage measurement with 1 mV resolution. Our work demonstrates the validity of the proposed models and the feasibility of near-field capacitive communication for wireless testing of ICs.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/93993/1/duelee_1.pd

Ring-Based Resonant Standing Wave Oscillators for 3D Clocking Applications

Ring-based resonant standing wave oscillators have been shown to be a useful clocking tech-nique that can distribute and generate a high frequency, low skew, low power, and stable clock signal. By using through-silicon-vias, this type of standing wave oscillator can be used to gener-ate the clocking scheme for 3D integrated circuits. In this thesis, we propose the use of such 3D standing wave oscillators and show how independent 3D oscillators in different stacks can syn-chronize through the use of a redistribution layer stub. Inter-chip clock synchronization is then accomplished without the need for a PLL. In addition, we propose the first 3D ring-based resonant standing wave oscillator bootstrap and reset circuit to initialize and stop oscillation. Using a 3D ring-based resonant standing wave oscillator, we propose a ring-based data fabric for 3D stacked DRAM and compare the results with existing approaches such as High Bandwidth Memory (HBM) or Wide I/O memory. We show that our Memory Architecture using a Ring-based Scheme (MARS) can provide the increases in speed necessary to overcome current memory bottlenecks, and can scale effectively as future 3D stacks become larger. Our MARS can trade off power, throughput, and latency to match different application requirements. By using a narrow bus, and connecting it to all channels, the MARS8 can provide an alternative memory configuration with ∼ 6.9× lower power consumption than HBM, and ∼ 2.7× faster speeds than Wide I/O. Using multiple ring topologies in the same stack, the channel count can double from 8 to 16, and then to 32. This is possible since MARS uses about 4× fewer TSVs per channel than HBM or Wide I/O. This provides speeds up to ∼ 4.2× faster than traditional HBM. This scalable architecture allows higher throughput and faster system performance for next-generation DRAM. The MARS topology proposed in this thesis can be used in a variety of computing systems, from lightweight IoT to large-scale data centers

Synchronising coherent networked radar using low-cost GPS-disciplined oscillators

This text evaluates the feasibility of synchronising coherent, pulsed-Doppler, networked, radars with carrier frequencies of a few gigahertz and moderate bandwidths of tens of megahertz across short baselines of a few kilometres using low-cost quartz GPSDOs based on one-way GPS time transfer. It further assesses the use of line-of-sight (LOS) phase compensation, where the direct sidelobe breakthrough is used as the phase reference, to improve the GPS-disciplined oscillator (GPSDO) synchronised bistatic Doppler performance. Coherent bistatic, multistatic, and networked radars require accurate time, frequency, and phase synchronisation. Global positioning system (GPS) synchronisation is precise, low-cost, passive and covert, and appears well-suited to synchronise networked radar. However, very few published examples exist. An imperfectly synchronised bistatic transmitter-receiver is modelled. Measures and plots are developed enabling the rapid selection of appropriate synchronisation technologies. Three low-cost, open, versatile, and extensible, quartz-based GPSDOs are designed and calibrated at zero-baselines. These GPSDOs are uniquely capable of acquiring phase-lock four times faster than conventional phase-locked loops (PLLs) and a new time synchronisation mechanism enables low-jitter sub-10 ns oneway GPS time synchronisation. In collaboration with University College London, UK, the 2.4 GHz coherent pulsed-Doppler networked radar, called NetRAD, is synchronised using the University of Cape Town developed GPSDOs. This resulted in the first published example of pulsed-Doppler phase synchronisation using GPS. A tri-static experiment is set up in Simon’s Bay, South Africa, with a maximum baseline of 2.3 km. The Roman Rock lighthouse was used as a static target to simultaneously assess the range, frequency, phase, and Doppler performance of the monostatic, bistatic, and LOS phase corrected bistatic returns. The real-world results compare well to that predicted by the earlier developed bistatic model and zero-baseline calibrations. GPS timing limits the radar bandwidth to less than 37.5 MHz when it is required to synchronise to within the range resolution. Low-cost quartz GPSDOs offer adequate frequency synchronisation to ensure a target radial velocity accuracy of better than 1 km/h and frequency drift of less than the Doppler resolution over integration periods of one second or less. LOS phase compensation, when used in combination with low-cost GPSDOs, results in near monostatic pulsed-Doppler performance with a subclutter visibility improvement of about 30 dB

The design and implementation of a wideband digital radio receiver

Historically radio has been implemented using largely analogue circuitry. Improvements in mixed signal and digital signal processing technology are rapidly leading towards a largely digital approach, with down-conversion and filtering moving to the digital signal processing domain. Advantages of this technology include increased performance and functionality, as well as reduced cost. Wideband receivers place the heaviest demands on both mixed signal and digital signal processing technology, requiring high spurious free dynamic range (SFDR) and signal processing bandwidths. This dissertation investigates the extent to which current digital technology is able to meet these demands and compete with the proven architectures of analogue receivers. A scalable generalised digital radio receiver capable of operating in the HF and VHF bands was designed, implemented and tested, yielding instantaneous bandwidths in excess of 10 MHz with a spurious-free dynamic range exceeding 80 decibels below carrier (dBc). The results achieved reflect favourably on the digital receiver architecture. While the necessity for minimal analogue circuitry will possibly always exist, digital radio architectures are currently able to compete with analogue counterparts. The digital receiver is simple to manufacture, based on the use of largely commercial off-the-shelf (COTS) components, and exhibits extreme flexibility and high performance when compared with comparably priced analogue receivers

Optoelectronic oscillator for 5G wireless networks and beyond

With the development of 5G wireless network and beyond, the wireless carrier frequency will definitely reach millimeter-wave (mm-wave) and even terahertz (THz). As one of the key elements in wireless networks, the local oscillator (LO) needs to operate at mm-wave and THz band with lower phase noise, which becomes a major challenge for commercial LOs. In this article, we investigate the recent developments of the electronic integrated circuit (EIC) oscillator and the optoelectronic oscillator (OEO), and especially investigate the prospect of OEO serving as a qualified LO in the 5G wireless network and beyond. Both the EIC oscillators and OEOs are investigated, including their basic theories of operation, representative techniques and some milestones in applications. Then, we compare the performances between the EIC oscillators and the OEOs in terms of frequency accuracy, phase noise, power consumption and cost. After describing the specific requirements of LO based on the standard of 5G and 6G wireless communication systems, we introduce an injection-locked OEO architecture which can be implemented to distribute and synchronize LOs. The OEO has better phase noise performance at high frequency, which is greatly desired for LO in 5G wireless network and beyond. Besides, the OEO provides an easy and low-loss method to distribute and synchronize mm-wave and THz LOs. Thanks to photonic integrated circuit development, the power consumption and cost of OEO reduce gradually. It is foreseeable that the integrated OEO with lower cost may have a promising prospect in the 5G wireless network and beyond

Cavity-enhanced direct frequency comb spectroscopy

Cavity-enhanced direct frequency comb spectroscopy combines broad spectral bandwidth, high spectral resolution, precise frequency calibration, and ultrahigh detection sensitivity, all in one experimental platform based on an optical frequency comb interacting with a high-finesse optical cavity. Precise control of the optical frequency comb allows highly efficient, coherent coupling of individual comb components with corresponding resonant modes of the high-finesse cavity. The long cavity lifetime dramatically enhances the effective interaction between the light field and intracavity matter, increasing the sensitivity for measurement of optical losses by a factor that is on the order of the cavity finesse. The use of low-dispersion mirrors permits almost the entire spectral bandwidth of the frequency comb to be employed for detection, covering a range of ~10% of the actual optical frequency. The light transmitted from the cavity is spectrally resolved to provide a multitude of detection channels with spectral resolutions ranging from a several gigahertz to hundreds of kilohertz. In this review we will discuss the principle of cavity-enhanced direct frequency comb spectroscopy and the various implementations of such systems. In particular, we discuss several types of UV, optical, and IR frequency comb sources and optical cavity designs that can be used for specific spectroscopic applications. We present several cavity-comb coupling methods to take advantage of the broad spectral bandwidth and narrow spectral components of a frequency comb. Finally, we present a series of experimental measurements on trace gas detections, human breath analysis, and characterization of cold molecular beams.Comment: 36 pages, 27 figure