A power efficient delta-sigma ADC with series-bilinear switch capacitor voltage-controlled oscillator

In low-power VLSI design applications non-linearity and harmonics are a major dominant factor which affects the performance of the ADC. To avoid this, the new architecture of voltage-controlled oscillator (VCO) was required to solve the non-linearity issues and harmonic distortion. In this work, a 12-bit, 200MS/s low power delta-sigma analog to digital converter (ADC) VCO based quantizer was designed using switched capacitor technique. The proposed technique uses frequency to current conversion technique as a linearization method to reduce the non-linearity issue. Simulation result show that the proposed 12-bit delta-sigma ADC consumes the power of 2.68 mW and a total area of 0.09 mm² in 90 nm CMOS process

Noise shaping Asynchronous SAR ADC based time to digital converter

Time-to-digital converters (TDCs) are key elements for the digitization of timing information in modern mixed-signal circuits such as digital PLLs, DLLs, ADCs, and on-chip jitter-monitoring circuits. Especially, high-resolution TDCs are increasingly employed in on-chip timing tests, such as jitter and clock skew measurements, as advanced fabrication technologies allow fine on-chip time resolutions. Its main purpose is to quantize the time interval of a pulse signal or the time interval between the rising edges of two clock signals. Similarly to ADCs, the performance of TDCs are also primarily characterized by Resolution, Sampling Rate, FOM, SNDR, Dynamic Range and DNL/INL. This work proposes and demonstrates 2nd order noise shaping Asynchronous SAR ADC based TDC architecture with highest resolution of 0.25 ps among current state of art designs with respect to post-layout simulation results. This circuit is a combination of low power/High Resolution 2nd Order Noise Shaped Asynchronous SAR ADC backend with simple Time to Amplitude converter (TAC) front-end and is implemented in 40nm CMOS technology. Additionally, special emphasis is given on the discussion on various current state of art TDC architectures.Electrical and Computer Engineerin

Design and Analysis of a Low-Power 8-Bit 500 KS/S SAR ADC for Bio-Medical Implant Devices

This thesis project involves the design and analysis of an 8-bit Successive Approximation Register (SAR) Analog to Digital Convertor (ADC), designed for low- power applications such as bio-medical implants. The sampling rate for this ADC is 500 KS/s. The power consumption for the whole SAR ADC system was measured to be 2.1 uW. The novelty of this project is the proposal of an extremely energy efficient comparator architecture. The result is the design of a final ADC with reasonable sampling speed, accuracy and low power consumption. In this project, all the different subsystems have been designed at the transistor level with 45 nm CMOS technology. The logical circuit was designed using Verilog language. It was then synthesized and integrated in the overall system

A 60-Gb/s PAM4 Wireline Receiver With 2-Tap Direct Decision Feedback Equalization Employing Track-and-Regenerate Slicers in 28-nm CMOS

This article describes a 4-level pulse amplitude modulation (PAM4) receiver incorporating continuous time linear equalizers (CTLEs) and a 2-tap direct decision feedback equalizer (DFE) for applications in wireline communication. A CMOS track-and-regenerate slicer is proposed and employed in the PAM4 receiver. The proposed slicer is designed for the purposes of improving the clock-to-Q delay as well as the output signal swing. A direct DFE in a PAM4 receiver is made possible with the proposed slicer by having rail-to-rail digital feedback signals available with reduced delay, and accordingly relaxing the settling time constraint of the summer. With the 2-tap direct DFE enabled by the proposed slicer, loop-unrolling and inductor-based bandwidth enhancement techniques, which can be area/power intensive, are not necessary at high data rates. The PAM4 receiver fabricated in 28-nm CMOS technology achieves bit-error-rate (BER) better than 1E-12, and energy efficiency of 1.1 pJ/b at 60 Gb/s, measured over a channel with 8.2-dB loss at Nyquist

Digital Background Self-Calibration Technique for Compensating Transition Offsets in Reference-less Flash ADCs

This Dissertation focusses on proving that background calibration using adaptive algorithms are low-cost, stable and effective methods for obtaining high accuracy in flash A/D converters. An integrated reference-less 3-bit flash ADC circuit has been successfully designed and taped out in UMC 180 nm CMOS technology in order to prove the efficiency of our proposed background calibration. References for ADC transitions have been virtually implemented built-in in the comparators dynamic-latch topology by a controlled mismatch added to each comparator input front-end. An external very simple DAC block (calibration bank) allows control the quantity of mismatch added in each comparator front-end and, therefore, compensate the offset of its effective transition with respect to the nominal value. In order to assist to the estimation of the offset of the prototype comparators, an auxiliary A/D converter with higher resolution and lower conversion speed than the flash ADC is used: a 6-bit capacitive-DAC SAR type. Special care in synchronization of analogue sampling instant in both ADCs has been taken into account. In this thesis, a criterion to identify the optimum parameters of the flash ADC design with adaptive background calibration has been set. With this criterion, the best choice for dynamic latch architecture, calibration bank resolution and flash ADC resolution are selected. The performance of the calibration algorithm have been tested, providing great programmability to the digital processor that implements the algorithm, allowing to choose the algorithm limits, accuracy and quantization errors in the arithmetic. Further, systematic controlled offset can be forced in the comparators of the flash ADC in order to have a more exhaustive test of calibration

Design of low-voltage power efficient frequency dividers in folded MOS current mode logic

In this paper we propose a methodology to design high-speed, power-efficient static frequency dividers based on the low-voltage Folded MOS Current Mode Logic (FMCML) approach. A modeling strategy to analyze the dependence of propagation delay and power consumption on the bias currents of the divide-by-2 (DIV2) cell is introduced. We demonstrate that the behavior of the FMCML DIV2 cell is different both from the one of the conventional MCML DFF (D-type Flip-Flop) and from FMCML DFF without a level shifter. Then an analytical strategy to optimize the divider in different design scenarios: maximum speed, minimum power-delay product (PDP) or minimum energy-delay product (EDP) is presented. The possibility to scale the bias currents through the divider stages without affecting the speed performance is also investigated. The proposed analytical approach allows to gain a deep insight into the circuit behavior and to comprehensively optimize the different design tradeoffs. The derived models and design guidelines are validated against transistor level simulations referring to a commercial 28nm FDSOI CMOS process. Different divide-by-8 circuits following different optimization strategies have been designed in the same 28nm CMOS technology showing the effectiveness of the proposed methodology

Performance enhancement in the desing of amplifier and amplifier-less circuits in modern CMOS technologies.

In the context of nowadays CMOS technology downscaling and the increasing demand of high performance electronics by industry and consumers, analog design has become a major challenge. On the one hand, beyond others, amplifiers have traditionally been a key cell for many analog systems whose overall performance strongly depends on those of the amplifier. Consequently, still today, achieving high performance amplifiers is essential. On the other hand, due to the increasing difficulty in achieving high performance amplifiers in downscaled modern technologies, a different research line that replaces the amplifier by other more easily achievable cells appears: the so called amplifier-less techniques. This thesis explores and contributes to both philosophies. Specifically, a lowvoltage differential input pair is proposed, with which three multistage amplifiers in the state of art are designed, analysed and tested. Moreover, a structure for the implementation of differential switched capacitor circuits, specially suitable for comparator-based circuits, that features lower distortion and less noise than the classical differential structures is proposed, an, as a proof of concept, implemented in a ΔΣ modulator

Design of high speed folding and interpolating analog-to-digital converter

High-speed and low resolution analog-to-digital converters (ADC) are key elements in the read channel of optical and magnetic data storage systems. The required resolution is about 6-7 bits while the sampling rate and effective resolution bandwidth requirements increase with each generation of storage system. Folding is a technique to reduce the number of comparators used in the flash architecture. By means of an analog preprocessing circuit in folding A/D converters the number of comparators can be reduced significantly. Folding architectures exhibit low power and low latency as well as the ability to run at high sampling rates. Folding ADCs employing interpolation schemes to generate extra folding waveforms are called "Folding and Interpolating ADC" (F&I ADC). The aim of this research is to increase the input bandwidth of high speed conversion, and low latency F&I ADC. Behavioral models are developed to analyze the bandwidth limitation at the architecture level. A front-end sample-and-hold unit is employed to tackle the frequency multiplication problem, which is intrinsic for all F&I ADCs. Current-mode signal processing is adopted to increase the bandwidth of the folding amplifiers and interpolators, which are the bottleneck of the whole system. An operational transconductance amplifier (OTA) based folding amplifier, current mirror-based interpolator, very low impedance fast current comparator are proposed and designed to carry out the current-mode signal processing. A new bit synchronization scheme is proposed to correct the error caused by the delay difference between the coarse and fine channels. A prototype chip was designed and fabricated in 0.35μm CMOS process to verify the ideas. The S/H and F&I ADC prototype is realized in 0.35μm double-poly CMOS process (only one poly is used). Integral nonlinearity (INL) is 1.0 LSB and Differential nonlinearity (DNL) is 0.6 LSB at 110 KHz. The ADC occupies 1.2mm2 active area and dissipates 200mW (excluding 70mW of S/H) from 3.3V supply. At 300MSPS sampling rate, the ADC achieves no less than 6 ENOB with input signal lower than 60MHz. It has the highest input bandwidth of 60MHz reported in the literature for this type of CMOS ADC with similar resolution and sample rate