A 3D printed monolithic soft gripper with adjustable stiffness

Soft robotics has recently gained a significant momentum as a newly emerging field in robotics that focuses on biomimicry, compliancy and conformability with safety in near-human environments. Beside conventional fabrication methods, additive manufacturing is a primary technique to employ to fabricate soft robotic devices. We developed a monolithic soft gripper, with variable stiffness fingers, that was fabricated as a one-piece device. Negative pressure was used for the actuation of the gripper while positive pressure was used to vary the stiffness of the fingers of the gripper. Finger bending and gripping capabilities of the monolithic soft gripper were experimentally tested. Finite element simulation and experimental results demonstrate that the proposed monolithic soft gripper is fully compliant, low cost and requires an actuation pressure below -100 kPa

Approximate Piecewise Constant Curvature Equivalent Model and Their Application to Continuum Robot Configuration Estimation

The continuum robot has attracted more attention for its flexibility. Continuum robot kinematics models are the basis for further perception, planning, and control. The design and research of continuum robots are usually based on the assumption of piecewise constant curvature (PCC). However, due to the influence of friction, etc., the actual motion of the continuum robot is approximate piecewise constant curvature (APCC). To address this, we present a kinematic equivalent model for continuum robots, i.e. APCC 2L-5R. Using classical rigid linkages to replace the original model in kinematic, the APCC 2L-5R model effectively reduces complexity and improves numerical stability. Furthermore, based on the model, the configuration self-estimation of the continuum robot is realized by monocular cameras installed at the end of each approximate constant curvature segment. The potential of APCC 2L-5R in perception, planning, and control of continuum robots remains to be explored

Electroactive polymers as soft robotic actuators: Electromechanical modeling and identification

Biologically inspired robotic applications have recently received significant attention due to developments in novel materials and actuators with an operation principle similar to the natural muscles’. Electroactive polymer (EAP) actuators, also known as artificial muscles, possess extraordinary properties such as low efficiency consumption, compliance, bio-compatibility and ability to be miniaturized. Although several methodologies have been proposed for modeling and identification of their quasi-static bending behavior, a negligibly small attention has been given to their dynamic behavior. In this paper, we, therefore, report on their electromechanical modeling and parameter identification. We model the tri-layer EAP actuators as a soft robotic actuator consisting of a significant number of rigid links connected with compliant revolute joints. The experimental and numerical results presented suggest that the soft robotics approach is an effective way to model the EAP actuator and subsequently identify its dynamic parameters accurately. We have previously employed the same soft robotic approach to estimate the whole shape of the EAP actuator as a function of time

3D printed flexure hinges for soft monolithic prosthetic fingers

Mechanical compliance is one of the primary properties of structures in nature playing a key role in their efficiency. This study investigates a number of commonly used flexure hinges to determine a flexure hinge morphology, which generates large displacements under a lowest possible force input. The aim of this is to design a soft and monolithic robotic finger. Fused deposition modeling, a low-cost 3D printing technique, was used to fabricate the flexure hinges and the soft monolithic robotic fingers. Experimental and finite element analyses suggest that a nonsymmetric elliptical flexure hinge is the most suitable type for use in the soft monolithic robotic finger. Having estimated the effective elastic modulus, flexion of the soft monolithic robotic fingers was simulated and this showed a good correlation with the actual experimental results. The soft monolithic robotic fingers can be employed to handle objects with unknown shapes and are also potential low-cost candidates for establishing soft and one-piece prosthetic hands with light weight. A three-finger gripper has been constructed using the identified flexure hinge to handle objects with irregular shapes such as agricultural products

Novel Vine-like Continuum Robot for Environmental Exploration Applications

This thesis details a new design and novel operational strategies for nature inspired, thin tendril continuum robots. Instead of taking inspiration for robot design from insects or animals, the novel approach to continuum robotics herein takes inspiration and adapts operational concepts from plant life. In particular, an innovative strategy is developed which mimics behaviors observed in vines and other climbing plants. Specifically, a tendril robot with prickles was developed and deployed to actively seek environmental contact, exploiting the mechanical advantage gained by bracing against the environment using the prickles. The resulting performance enhancements over previously developed smooth backbone tendril robot designs, and use of strategies that do not attempt to interact with the environment are empirically demonstrated with the new robot prototype. Results of further experiments suggest applications in which the new design and approach could prove useful to the scientific and wider communities

Robots Hiper-Redundantes: Clasificación, Estado del Arte y Problemática

Los robots hiper-redundantes son aquellos que tienen un número muy elevado de grados de libertad. En su uso cotidiano, la redundancia es referida para indicar una repetición o un uso excesivo de un concepto. En el campo de la robótica, la redundancia puede ofrecer numerosos beneficios frente a los robots convencionales. Los robots hiper-redundantes poseen una mayor habilidad para sortear obstáculos, son tolerantes a fallos en algunas de sus articulaciones y también pueden ofrecer ventajas cinemáticas. En este artículo se presentan los conceptos generales para entender este tipo de robots, así como una clasificación de los mismos, su potencial, su problemática y su evolución a lo largo de la historia

Modeling and Verification of a Multi-section Continuum Robot

Continuum robots mimic the principle of a special biological structure known as the muscular hydrostat. These robots have an ability to bend at any location on along its backbone and have potential applications in disaster relief, medical surgeries and nuclear waste disposal. This thesis presents the modeling and verification of a multi-section continuum robot by applying the Cosserat theory of rods. Next, 2D verification is performed on a continuum robot based on a backbone composed of a nickel titanium alloy. In addition, the thesis develops the theoretical foundations for a cable-driven continuum robot by studying the effects of cable guide mass which cause additional deformation of the robot The results of this thesis show that the multi-section model is accurate within 3.4% in predicting the Cartesian tip coordinates, and the model with the cable guides accurate within 1.26% error in predicted versus the observed Cartesian tip coordinates of the backbone

Operational Strategies for Continuum Manipulators

We introduce a novel, intuitive user interface for continuum manipulators through the use of various joystick mappings. This user interface allows for the effective use of continuum manipulators in the lab and in the field. A novel geometric approach is developed to produce a more intuitive understanding of continuum manipulator kinematics. Using this geometric approach we derive the first closed-form solution to the inverse kinematics problem for continuum robots. Using the derived inverse kinematics to convert from workspace coordinates to configuration space coordinates we develop a potential-field path planner for continuum manipulators

A New Approach to Dynamic Modeling of Continuum Robots

ABSTRACT In this thesis, a new approach for developing practically realizable dynamic models for continuum robots is proposed. Based on the new dynamic models developed, a novel technique for analyzing the capabilities of continuum manipulators to be employed in various real world applications has also been proposed and developed. A section of a continuum arm is modeled using lumped model elements (masses, springs and dampers). It is shown that this model, although an approximation to a continuum structure, can be used to conveniently analyze the dynamics of the arm with suitable tradeoff in accuracy of modeling. This relatively simple model is more plausible to implement in an actual real-time controller when compared to other techniques of modeling continuum arms. Principles of Lagrangian dynamics are used to derive the expressions for the generalized forces in the system. The force exerted by McKibben actuators at different pressure level - length pairs is characterized and is incorporated into this dynamic model. The constraints introduced in the analytical model conform to the physical and operational limitations of the Octarm VI continuum robot manipulator. The model is validated by comparing the results of numerical simulation with the physical measurements of a continuum arm prototype built using McKibben actuators. Based on the new lumped parameter dynamic model developed for continuum robots, a technique for deducing measures of manipulability, forces and impacts that can be sustained or imparted by the tip of a continuum robot has been developed. These measures are represented in the form of ellipsoids whose volume and orientation gives information about the various functional capabilities (end effector velocities, forces and impacts) of the arm at a particular configuration. The above mentioned ellipsoids are exemplified for different configurations of the continuum section arm and their physical significances are analyzed. The new techniques proposed and methodologies adopted in this thesis supported by experimental results represent a significant contribution to the field of continuum robots

Design and analysis of jammable granular systems

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Mechanical Engineering, 2013.Cataloged from PDF version of thesis.Includes bibliographical references (p. 102-110).Jamming--the mechanism by which granular media can transition between liquid-like and solid-like states-has recently been demonstrated as a variable strength and stiffness mechanism in a range of applications. As a low-cost and simple means for achieving tunable mechanical properties, jamming has been used in systems ranging from architectural to medical ones. This thesis explores the utility of jamming for robotic manipulation applications, both at a fundamental level of understanding how granular properties affect the performance of jammed systems, and at a more applied level of designing functional robotic components. Specifically, the purpose of this thesis was to enable engineers to design jammable robotic systems in a principled manner. Three parallel yet related studies were conducted to work towards this goal. First, an experimental analysis was conducted to determine whether the bulk shear strength of granular systems can be correlated with grain properties-such as ones concerning shape, size distribution, and surface texture-extracted from 2D silhouettes of grains. Second, a novel medium composed of a mixture of hard and soft spheres was proposed to achieve variable strength and stiffness properties as a function of confining pressure; experimental analysis was conducted on this system with not only varying confining pressures but also varying mixing ratios of hard and soft spheres. Finally, the design and analysis of a novel jammable robotic manipulator-with the goal of maximizing both the strength and articulation of the system-is presented.by Nadia G. Cheng.Ph.D