Reducing MOSFET 1/f Noise and Power Consumption by "Switched Biasing"

Switched biasing is proposed as a technique for reducing the 1/f noise in MOSFET's. Conventional techniques, such as chopping or correlated double sampling, reduce the effect of 1/f noise in electronic circuits, whereas the switched biasing technique reduces the 1/f noise itself. Whereas noise reduction techniques generally lead to more power consumption, switched biasing can reduce the power consumption. It exploits an intriguing physical effect: cycling a MOS transistor from strong inversion to accumulation reduces its intrinsic 1/f noise. As the 1/f noise is reduced at its physical roots, high frequency circuits, in which 1/f noise is being upconverted, can also benefit. This is demonstrated by applying switched biasing in a 0.8 ¿m CMOS sawtooth oscillator. By periodically switching off the bias currents, during time intervals that they are not contributing to the circuit operation, a reduction of the 1/f noise induced phase noise by more than 8 dB is achieved, while the power consumption is also reduced by 30

Arrayable Voltage-Controlled Ring-Oscillator for Direct Time-of-Flight Image Sensors

Direct time-of-flight (d-ToF) estimation with high frame rate requires the incorporation of a time-to-digital converter (TDC) at pixel level. A feasible approach to a compact implementation of the TDC is to use the multiple phases of a voltage-controlled ring-oscillator (VCRO) for the finest bits. The VCRO becomes central in determining the performance parameters of a d-ToF image sensor. In this paper, we are covering the modeling, design, and measurement of a CMOS pseudo-differential VCRO. The oscillation frequency, the jitter due to mismatches and noise and the power consumption are analytically evaluated. This design has been incorporated into a 64x64-pixel array. It has been fabricated in a 0.18 mu m standard CMOS technology. Occupation area is 28x29 mu m(2) and power consumption is 1.17 mW at 850 MHz. The measured gain of the VCRO is of 477 MHz/V with a frequency tuning range of 53%. Moreover, it features a linearity of 99.4% over a wide range of control frequencies, namely, from 400 to 850 MHz. The phase noise is of -102 dBc/Hz at 2 MHz offset frequency from 850 MHz. The influence of these parameters in the performance of the TDC has been measured. The minimum time bin of the TDC is 147 ps with a rms DNL/INL of 0.13/1.7LSB.Office of Naval Research (USA) N000141410355Ministerio de Economía y Competitividad TEC2015-66878-C3-1-RJunta de Andalucía P12-TIC 233

Low Power Adaptive Circuits: An Adaptive Log Domain Filter and A Low Power Temperature Insensitive Oscillator Applied in Smart Dust Radio

This dissertation focuses on exploring two low power adaptive circuits. One is an adaptive filter at audio frequency for system identification. The other is a temperature insensitive oscillator for low power radio frequency communication. The adaptive filter is presented with integrated learning rules for model reference estimation. The system is a first order low pass filter with two parameters: gain and cut-off frequency. It is implemented using multiple input floating gate transistors to realize online learning of system parameters. Adaptive dynamical system theory is used to derive robust control laws in a system identification task. Simulation results show that convergence is slower using simplified control laws but still occurs within milliseconds. Experimental results confirm that the estimated gain and cut-off frequency track the corresponding parameters of the reference filter. During operation, deterministic errors are introduced by mismatch within the analog circuit implementation. An analysis is presented which attributes the errors to current mirror mismatch. The harmonic distortion of the filter operating in different inversion is analyzed using EKV model numerically. The temperature insensitive oscillator is designed for a low power wireless network. The system is based on a current starved ring oscillator implemented using CMOS transistors instead of LC tank for less chip area and power consumption. The frequency variance with temperature is compensated by the temperature adaptive circuits. Experimental results show that the frequency stability from 5°C to 65°C has been improved 10 times with automatic compensation and at least 1 order less power is consumed than published competitors. This oscillator is applied in a 2.2GHz OOK transmitter and a 2.2GHz phase locked loop based FM receiver. With the increasing needs of compact antenna, possible high data rate and wide unused frequency range of short distance communication, a higher frequency phase locked loop used for BFSK receiver is explored using an LC oscillator for its capability at 20GHz. The success of frequency demodulation is demonstrated in the simulation results that the PLL can lock in 0.5μs with 35MHz lock-in range and 2MHz detection resolution. The model of a phase locked loop used for BFSK receiver is analyzed using Matlab

CIRCUIT MODULES FOR BROADBAND CMOS SIX-PORT SYSTEMS

This dissertation investigates four circuit modules used in a CMOS integrated six-port measurement system. The first circuit module is a wideband power source generator, which can be implemented with a voltage controlled ring oscillator. The second circuit module is a low-power 0.5 GHz - 20.5 GHz power detector with an embedded amplifier and a wideband quasi T-coil matching network. The third circuit module is a six-port circuit, which can be implemented with distributed or lumped- lement techniques. The fourth circuit module is the phase sifter used as calibration loads. The theoretical analysis, circuit design, simulated or experimental verifications of each circuit module are also included

A Subthreshold Current-Sensing Sigma-Delta Modulator for Low-Voltage and Low-Power Sensor Interfaces

A continuous-time (CT) ΣΔ modulator for sensing and direct analog-to-digital conversion of nA-range (subthreshold) currents is presented in this work. The presented modulator uses a subthreshold technique based on subthreshold source-coupled logic cells to efficiently convert subthreshold current to digital code without performing current-to-voltage conversion. As a benefit of this technique, the current-sensing CT ΣΔ modulator operates at low voltage and consumes very low power, which makes it convenient for low-power and low-voltage current-mode sensor interfaces. The prototype design is implemented in a 0.18 µm standard complementary metal-oxide semiconductor technology. The modulator operates with a supply voltage of 0.8 V and consumes 5.43 μW of power at the maximum bandwidth of 20 kHz. The obtainable current-sensing resolution ranges from effective number of bits (ENOB) = 7.1 bits at a 5 kHz bandwidth to ENOB = 6.5 bits at a 20 kHz bandwidth (ENOB). The obtained power efficiency (peak FoM = 1.5 pJ/conv) outperforms existing current-mode analog-to-digital converter designs and is comparable with the voltage-mode CT ΣΔ modulators. The modulator generates very low levels of switching noise thanks to CT operation and subthreshold current-mode circuits that draw a constant subthreshold current from the voltage supply. The presented modulator is used as a readout interface for sensors with current-mode output in ultra low-power conditions and is also suitable to perform on-chip current measurements in power management circuits

Novel Current-Mode Sensor Interfacing and Radio Blocks for Cell Culture Monitoring

Since 2004 Imperial College has been developing the world’s first application-specific instrumentation aiming at the on-line, in-situ, physiochemical monitoring of adult stem cell cultures. That effort is internationally known as the ‘Intelligent Stem Cell Culture Systems’ (ISCCS) project. The ISCCS platform is formed by the functional integration of biosensors, interfacing electronics and bioreactors. Contrary to the PCB-level ISCCS platform the work presented in this thesis relates to the realization of a miniaturized cell culture monitoring platform. Specifically, this thesis details the synthesis and fabrication of pivotal VLSI circuit blocks suitable for the construction of a miniaturized microelectronic cell monitoring platform. The thesis is composed of two main parts. The first part details the design and operation of a two-stage current-input currentoutput topology suitable for three-electrode amperometric sensor measurements. The first stage is a CMOS-dual rail-class AB-current conveyor providing a low impedancevirtual ground node for a current input. The second stage is a novel hyperbolic-sinebased externally-linear internally-non-linear current amplification stage. This stage bases its operation upon the compressive sinh−1 conversion of the interfaced current to an intermediate auxiliary voltage and the subsequent sinh expansion of the same voltage. The proposed novel topology has been simulated for current-gain values ranging from 10 to 1000 using the parameters of the commercially available 0.8μm AMS CMOS process. Measured results from a chip fabricated in the same technology are also reported. The proposed interfacing/amplification architecture consumes 0.88-95μW. The second part describes the design and practical evaluation of a 13.56MHz frequency shift keying (FSK) short-range (5cm) telemetry link suitable for the monitoring of incubated cultures. Prior to the design of the full FSK radio system, a pair of 13.56MHz antennae are characterized experimentally. The experimental S-parameter-value determination of the 13.56MHz wireless link is incorporated into the Cadence Design Framework allowing a high fidelity simulation of the reported FSK radio. The transmitter of the proposed system is a novel multi-tapped seven-stage ring-oscillator-based VCO whereas the core of the receiver is an appropriately modified phase locked loop (PLL). Simulated and measured results from a 0.8μm CMOS technology chip are reported

Wide-Range Dynamic Power Management in Low-Voltage Low-Power Subthreshold SCL

Power-frequency scaling in subthreshold source coupled logic (STSCL) systems has been studied and analyzed. It is shown that the operating frequency of such systems can be adjusted over about three decades with linearly proportional power dissipation. The heart of such a system is a phase-locked loop (PLL)-based clock generator (CG) with a very wide tuning range controlling the dynamics of the STSCL system. The design of a wide tuning range PLL utilizing a novel self-adjustable loop filter that generates the reference clock as well as the bias current for the STSCL system is described. The PLL-based CG exhibits linear power-frequency characteristics in order to minimize its power consumption overhead (7 pJ with 350 nA standby current). Implemented in 0.13 μm CMOS, the CG occupies 0.06 mm2 with a supply voltage that can be reduced down to VDD = 0.9 V